• Proceedings of the KSME Conference
• /
• 2003.11a
• /
• pp.1384-1387
• /
• 2003

Pressurization test is usually required in aircraft full-scale static test. There are several test conditions including pressurization of cockpit, fuselage fuel tank, air inlet duct for T-50 full-scale static test. In this paper, the test conditions, equipment, piping analysis for the pressurization test are introduced. Tank simulation test is performed to verify the validity of piping analysis and to find good tuning parameters for the pressurization channel in the servo controller. Several test setup for pressurization of T-50 test is introduced. Test article volume is filled by form, $60%{\sim}80%$ volume is reduced for the T-50 full-scale static test. Pressurization system is connected to servo controller which also controls hydraulic actuator. Load and pressure control is synchronized by using the same servo controller during T-50 test. Typical control result for pressurization test condition is shown. Pressurization tests of T-50 full-scale static test was completed successfully.

• International Journal of Aerospace System Engineering
• /
• v.10 no.1
• /
• pp.1-13
• /
• 2023

The present study was attempted to investigate flow interference effects and the aerodynamic characteristics of the front and rear wings of a joined-wing aircraft by changing the configuration variables. The study was performed using a computational fluid dynamics(CFD) tool to demonstrate forward flight and analyze aerodynamic characteristics. A total of 9 configurations were analyzed with variations on the position, height, dihedral angle, incidence angle, twist angle, sweepback angle, and wing area ratio of the front and rear wings while the fuselage was fixed. The quantities of aerodynamic coefficients were confirmed in accordance with joined-wing configurations. The closer the front and rear wings were located, the greater the flow interference effects tended. Interestingly, the rear wing did not any configuration change, the lift coefficient of the rear wing was decreased when adjusted to increase the incidence angle of the front wing. The phenomenon was appeared due to an effective angle of attack alteration of the rear wing resulting from the flow interference by the front wing configurations.

• Journal of the Korean Society for Aviation and Aeronautics
• /
• v.31 no.2
• /
• pp.81-88
• /
• 2023

SHM (Structural Health Monitoring) technique for monitoring aircraft structural health and damage, EHM (Engine Health Monitoring) for monitoring aircraft engine performance, and APM (Application Performance Management) is used for each function. APMS (Airplane Performance Monitoring System) is a program that comprehensively applies these techniques to identify the difference between the performance manual provided by the manufacturer and the actual fuel mileage of the aircraft and reflect it in the flight plan. The main purpose of using APMS is to understand the performance of each aircraft, to plan and execute flights in an optimal way, and consequently to reduce fuel consumption. First, it is to check the fuel efficiency trend of each aircraft, check the correlation between the maintenance work performed and the fuel mileage, find the cause of the fuel mileage increase/decrease, and take appropriate measures in response. Second, it is to find the cause of fuel mileage degradation in detail by checking the trends by engine performance and fuselage drag effect. Third, the APMS is to be used in making maintenance work decisions. Through APMS, aircraft with below average fuel mileage are identified, the cause of fuel mileage degradation is identified, and appropriate corrective actions are determined. Fourth, APMS data is used to analyze the economic analysis of equipment installation investment. The cost can be easily calculated as the equipment installation cost, but the benefit is fuel efficiency improvement, and the only way to check this is the manufacturer's theory. Therefore, verifying the effect after installation and verifying the economic analysis is to secure the appropriateness of the investment. Through this, proper investment in fuel efficiency improvement equipment will be made, and fuel efficiency will be improved.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.50 no.10
• /
• pp.677-690
• /
• 2022

By using an actuator disk method based flow solver, aerodynamic analysis is carried out for a dual ducted fan aircraft, which is one of the VTOL compound aircrafts, and its associated ground effect is analyzed. The characteristics and accuracy of the solver for ground effect analysis is evaluated through a comparison with the results obtained from the sliding mesh technique. The aerodynamic performance and flow field characteristics with respect to the distance from the ground are analyzed. As the ground distance decreases, the fan thrust increases, but the deterioration of total normal force and hovering flight efficiency is identified owing to the decrease in the vertical force of the duct, fuselage, and wing. By examining the flow field in the bottom of the fuselage, the ground vortices and fountain flow generated by the interaction of the fan wake and ground are identified, and their influence on the aerodynamic performance is analyzed. The strength and characteristics of outwash with respect to the ground distance and azimuth direction are analyzed through comparison/examination of velocity profile. Influence of the ground effect with respect to collective pitch angle is also identified.

• Journal of the Korean Society of Visualization
• /
• v.8 no.2
• /
• pp.23-30
• /
• 2010

Regarding the aircrafts with a rotor blade system, the miniaturization of them is limited due to the rotor blade length and the tail rotor system. To miniaturize an aircraft, an equipment is required that increases thrust and also shortens the length of the rotor blade. The present study will conduct the flow analysis for miniaturizing the aircraft by applying a duct to the coaxial rotor blade system without tail rotor. First, the verification on the calculated results was conducted through the computational flow analysis on the coaxial rotor blade system without a duct. Then, the flow analysis for the coaxial rotor blade systems was performed including Ka-60 duct, Single duct, Twin duct, and Double duct, respectively. From the numerical results, the thrust coefficient appeared higher with the duct than without a duct for the coaxial rotor blade system. Especially, in the case of Double duct, the thrust was improved due to the increase of incoming flow and the extension of the wake area. These results will be used as the basic concepts for miniaturizing the aircraft with the rotor blade system. The flow analysis on the coaxial rotor blade system including the fuselage remains as a future work.

• Journal of Institute of Convergence Technology
• /
• v.5 no.2
• /
• pp.27-32
• /
• 2015

Air intakes are an essential component of aircraft engines. They are mainly used to offer uniform airflows to engine faces. Fighter aircraft have to mask the engine face inside the fuselage in order to reduce the Radar Cross Section(RCS). Therefore, offset intakes like a S-Duct are one of promising components for this purpose. During a fight, it is unavoidable that the flow will enter the intakes at some face angles other than zero. In this case, the performance of the aircraft engine will be influenced to the angle of incidence. In this study, the CFD analysis of the semi-circular S-Duct with AR(0.5,0) is performed to investigate the influence of the angle of incidence on the performance of the S-Duct using a distortion coefficient. To consider the adverse pressure gradient, a $k-{\omega}$ SST turbulence model is employed. The secondary flow and flow separation are observed for all computational cases. It is found that the positive incidence angle produces the best performances.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.17 no.2
• /
• pp.189-196
• /
• 2014

Automated design program using commercial process integration and optimization program was developed for conceptual design of fighter-class aircraft. Wind tunnel test data and performance analysis results were compared for the verification of analysis tool of this program, and the usefulness of the tool was found. After integration with radar cross section analysis tool, the correlation with configuration design variables of wing, tail and performance parameters was identified by design of experiment, and the optimized configuration for weight and RCS was derived from optimization of empty weight and average frontal RCS value. After parameter definition of fuselage, the program can be implemented for full aircraft configuration.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.24 no.1
• /
• pp.14-20
• /
• 2014

Recent developments for high altitude, long endurance conventional UAVs(HALE UAVs) have revealed new issues regarding aircraft structure design and analysis. First of all, due to intensive mission requirements, the structures of HALE UAVs have lightweight and very flexible main wing with high aspect ratio, and slender fuselage. For this kind of structures, aeroelastic characteristics are different from conventional aircrafts. Hence, currently developed analysis methods are not suitable to fully understand strucutral dynamics of the very flexible aircraft, and to guarantee structural reliability. Therefore, various structural studies considering nonlinear behaviors which are generally ignored for the conventional aircraft strucutral analyis have been attracting researchers interests. Nonlinear flutter of the very flexible wing is one of the subject to be studied in combination with strong coupling between aeroelastic characteristics and flight dynamics. Herein, as preliminary study, modeling and nonlinear system analysis of the 2D airfoild with torsional nonlinearity have been discussed.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2013.10a
• /
• pp.226-231
• /
• 2013

Recent developments for high altitude, long endurance conventional UAVs (HALE UAVs) have revealed new issues regarding aircraft structure design and analysis. First of all, due to intensive mission requirements, the structures of HALE UAVs have lightweight and very flexible main wing with high aspect ratio, and slender fuselage. For this kind of structures, aeroelastic characteristics are different from conventional aircrafts. Hence, currently developed analysis methods are not suitable to fully understand strucutral dynamics of the very flexible aircraft, and to guarantee structural reliability. Therefore, various structural studies considering nonlinear behaviors which are generally ignored for the conventional aircraft strucutral analyis have been attracting researchers interests. Nonlinear flutter of the very flexible wing is one of the subject to be studied in combination with strong coupling between aeroelastic characteristics and flight dynamics. Herein, as preliminary study, modeling and nonlinear system analysis of the 2D airfoild with torsional nonlinearity have been discussed.

• Journal of the Korean Society for Aviation and Aeronautics
• /
• v.32 no.2
• /
• pp.135-141
• /
• 2024

Despite the innovative technological advances in the aviation industry, hard landing events that occur during aircraft landing account for 13% of all accidents. Hard landing when landing an aircraft affects normal operation by generating a large load on the landing gear and the fuselage. In order to identify these risk factors, the airline monitors the high vertical acceleration event, a precursor to hard landing, through QAR (Quick Access Recorder) flight data analysis, and prepares and implements mitigation measures. In this study, it is intended to contribute to safety management based on flight data analysis that identifies the characteristics of high vertical acceleration G event data that can cause such hard landing and detailed parameters of precursor signs, and to identify the causal relationship of the occurrence of the event by applying statistical analysis methods such as variance analysis, correlation analysis, and regression analysis models to identify the characteristics of the event occurrence and eliminate the cause in advance.