• Journal of Advanced Navigation Technology
• /
• v.18 no.1
• /
• pp.29-34
• /
• 2014

Data fusion techniques combine data from multiple radars and related information to achieve more accurate estimations than could be achieved by a single, independent radar. In this paper, we analyze delay and loss of packets to be processed by multiple radar and minimize data processing interval from centralized data processing operation as fusing multiple radar data. Therefore, we model radar network about central data fusion, and analyze delay and loss of packets inside queues on assuming queues respectively as the M/M/1/K using NS-2. We confirmed average delay time, processing fused multiple radar data, through the analysis data. And then, this delay time can be used as a reference time for radar data latency in fusion center.

• Journal of Advanced Navigation Technology
• /
• v.24 no.6
• /
• pp.491-499
• /
• 2020

There are policies that foster the drone industry, which either put a legal precedent on drones through the "Drone Act" or grant a delay or exemption in applying the safety measures of "the Aviation Safety Act". Yet, the definition of a drone is unclear, requiring further discussion on commercial usage. Therefore, we have studied cases domestically and abroad, and also analyzed issues with the current aviation legislation. It was found that a drone is defined as "an unmanned aircraft where a pilot is not on board, and its net weight is 150 kg or less". However, there are several issues, such as that a drone taxi requires a pilot on board, and its weight is 150 kg or more. Thus, we propose to define a drone as "an unmanned aerial vehicle (provided, that its own net weight should be 300 kg or under, or not be limited to weight) under Article 2 (3) of the "Aviation Security Act" as prescribed by Ordinance of the Ministry of Land, Infrastructure, and Transport, which operates either by remote, automatically, or autonomously; or an unmanned aircraft under Article 2 (6) of the "Aviation Security Act".

• Journal of Navigation and Port Research
• /
• v.35 no.8
• /
• pp.619-624
• /
• 2011

A significant factor limiting the ranging accuracy of Loran (Long Range Navigation) signal is the additional secondary factor (ASF) in the time of arrival (TOA) measurements. Precise ASF values are essential if Loran deliver the high absolute accuracies demanded for aircraft approach, maritime harbour entrance. We measured the absolute propagation delay between Pohang Loran signal and Loran receiver output signal by comparing with Cesium atomic clock. In this study we measured ASFs between Pohang 9930M station and the 12 measurement points in the Yeongil Bay by using the measurement technique of absolute time delay. The measurement points were spaced at interval of 3 km by 3 km. An E-field antenna and an H-field antenna were used to improve the accuracy of ASF measurements and a DGPS (Differential GPS) receiver was used for accurate positions. We have gotten the result that the measured ASFs were compared with the predicted ASFs through this measurement technique.

• Composites Research
• /
• v.33 no.5
• /
• pp.296-301
• /
• 2020

Laminated composite materials have excellent in-plane properties, but are vulnerable in thickness directions, making it easy to delamination when bending and torsion loads are applied. Thickness directional reinforcement methods of composite materials that delay delamination include Z-pinning, Stitching, Tufting, etc., and typically Z-pinning and Stitching method are commonly used. The Z-pinning is reinforcement method by inserting metal or carbon pin in the thickness direction of prepreg, and the conventional stitching process is a method of reinforcing the mechanical properties in the thickness direction by intersecting the upper and lower fibers on the preform. In this paper, I-fiber stitching method, which complement and improve weakness of Z-pinning and Stitching method, was proposed, and the static strength of composite single-lap joints using I-fiber stitching process were evaluated. The single-lap joints were fabricated by a co-curing method using an autoclave vacuum bag process. The thickness of the composite adherend was fixed, and 5 types of specimens were manufactured with varying the stitching pattern (5×5, 7×7) and angle (0°, 45°). From the test, the failure load of the specimen reinforced by the I-fiber stitching process was increased by up to 143% compared to that of specimen without reinforcement.

• Composites Research
• /
• v.35 no.5
• /
• pp.322-327
• /
• 2022

Composite lap joints have been extensively used due to their excellent properties and the demand for light structures. However, due to the weak mechanical properties in the thickness direction, the lap joint is easily fractured. various reinforcement methods that delay fracture by dispersing stress concentration have been applied to overcome this problem, such as z-pinning and conventional stitching. The Z-pinning is reinforcement method by inserting metal or carbon pin in the thickness direction of prepreg, and the conventional stitching process is a method of reinforcing the mechanical properties in the thickness direction by intersecting the upper and lower fibers on the preform. I-fiber stitching method is a promising technology that combines the advantages of both z-pinning and the conventional stitching. In this paper, the static and fatigue strengths of the single-lap joints reinforced by the I-fiber stitching process were evaluated. The single-lap joints were fabricated by a co-curing method using an autoclave vacuum bag process and I-fiber reinforcing effects were evaluated according to adherend thickness and stitching angle. From the experiments, the thinner the composite joint specimen, the higher the I-fiber reinforcement effect, and Ifiber stitched single lap joints showed a 52% improvement in failure strength and 118% improvement in fatigue strength.

• Journal of the Korean Society for Aviation and Aeronautics
• /
• v.15 no.2
• /
• pp.18-24
• /
• 2007

The high ionospheric spatial gradient during ionospheric storm is the most concern when applying GNSS(Global Navigation Satellite System) augmentation systems for aircraft precision approach. Since the ionospheric gradient level depends on geographical location as well as the storm, understanding the ionospheric gradient statistics over a specific regional area is necessary for operating the augmentation systems. This paper compares three ionosphere gradient computation methods, direct differentiation between two receivers' ionospheric delay signal for a common satellite, derivation from a grid ionosphere map, and derivation from a plate ionosphere map. The plate map method provides a good indication on the gradient variation behavior over a regional area with limited number of GNSS receivers. The residual analysis for the ionosphere storm detection is discussed as well.

• Advances in aircraft and spacecraft science
• /
• v.1 no.1
• /
• pp.27-41
• /
• 2014

An active flow control technique based on "smart-tabs" is proposed to delay flow separation on a circular cylinder. The actuators are retractable and orientable multilayer piezoelectric tabs which protrude perpendicularly from the model surface. They are mounted along the spanwise direction with constant spacing. The effectiveness of the control was tested in pre-critical and in post-critical regime by evaluating the effects of several control parameters of the tabs like frequency, amplitude, height, angular position and plate incidence with respect to the local flow. Measurements of the mean static pressure distribution around the cylinder were used to estimate the pressure drag coefficient. The maximum drag reduction achieved in the pre-critical regime was of the order of 30%, whereas in the post-critical regime was about 10%, 3% of which due to active forcing. Furthermore, pressure fluctuation measurements were performed and spectral analysis indicated an almost complete suppression of the vortex shedding in active forcing conditions.

• Advances in aircraft and spacecraft science
• /
• v.1 no.1
• /
• pp.15-25
• /
• 2014

The developed concept of smart flow control based on turbulence scale modification was applied to control a flow around a circular cylinder. The concept was realized using arrays of vortex-generators regularly spaced along a cylinder generatrix with a given step. Mechanical and thermal vortex-generators were tested, the latter having been based on the localized surface heating or plasma discharges initiated with microwave radiation near the surface. Thus depending on a particular engineering solution, flow transport properties could be modified in passive or active ways. Matched numerical and experimental investigations showed a possibility to delay flow separation and, accordingly, to improve the aerodynamic performance of blunt bodies.

• 제어로봇시스템학회:학술대회논문집
• /
• 2001.10a
• /
• pp.148.2-148
• /
• 2001

The most important difference of an airship from conventional vehicle is that it has the apparent mass and inertia provided from the existence of Helium gas inside the airship. To acquire To acquire the exact response of the airship, the longitudinal responses of airship with respect to the vertical gust, which is the non-linear system, have been studied. An Airship has neutral buoyancy in equilibrium state. When it moves, its motion shows much difference comparing with conventional aircraft. Here, we compare two cases, the one has the apparent mass and the other hasn´t. With the apparent mass, the magnitude of the former response is smaller than the latter, while the frequency is higher. However, the apparent mass delay ...

• Aerospace Engineering and Technology
• /
• v.11 no.2
• /
• pp.65-72
• /
• 2012

Numerical simulations were performed to study the stall characteristics of turboprop aircraft. Stall characteristics were qualitatively investigated using the computational results of various configurations based on the combinations of propeller and high lift device. For the analysis of stall characteristics, three-dimensional Navier-Stokes solver with Spalart-Allmaras turbulence model was used and the relative motion between propeller and wing was simulated using sliding mesh technique. For the cruise configurations, major flow separation was occurred at the fuselage/wing fairing and the separation was reduced under propeller slipstream condition. For the high lift device configuration without propeller, major flow separation was occurred at the outboard side of nacelle. With rotating propeller, early stall onset due to low relative velocity and high effective angle of attack was observed on the outboard wing section. Regarding rotating direction of propeller, inboard-down direction was preferred due to the stall delay effect of propeller slipstream.