• 한국화재소방학회논문지
• /
• 제25권2호
• /
• pp.107-113
• /
• 2011

차동식 스포트형 공기 팽창식 열감지기를 인위적으로 높은 온도에서 가속열화시켜 경년변화되는 특성에 대하여 연구하였다. 이 연구는 현장에 설치된 감지기가 화재 또는 점검기기에 의한 고온의 열에 노출되었을 경우에 감지기의 동작에 미치는 영향을 분석하기 위하여 실험하였다. 실험결과 현장에서 5년 동안 사용되었던 2005년 B사 감지기는 $100^{\circ}C$의 온도에서 1시간 동안 노출되었을 경우에 감지기가 동작하지 않는 경우가 발생하였다. 이것은 감지기 감열실내의 팽창된 공기가 리크공 이외의 곳에서 리크 되었기 때문인 것으로 판단된다. 그러나 감지기의 동작표시를 나타내는 LED는 온도가 $160^{\circ}C$까지 올라갔음에도 불구하고 모두 정상적으로 동작하였다. 따라서 동작표시 LED의 회로소자는 고장은 발생하지 않았음을 알 수 있었다.

• 한국의학물리학회지:의학물리
• /
• 제15권2호
• /
• pp.59-62
• /
• 2004

본 논문에서는 마이크로필름과 탄소막 전극을 이용하여 개발한 소형 방사선측정기의 특성을 평가하였다. 전극은 5 mm 직경의 고전압전극, 3.3 mm 직경의 수집전극, 그리고 넓이가 0.7 mm인 보호전극으로 구성되었으며, 이온수집 공동의 부피는 0.016 ㎤이었다. 6 MV X-선을 이용하여 제작된 측정기에 대한 전기적 특성을 조사하였는데, 누설전류는 0.1 pA, 재현 오차가 0.1% 이하, 선량률 효과는 1.5% 이하, 분극효과는 2.4% 이하로 나타났다. 개발된 측정기의 전기적 특성은 양호한 것으로 평가되며, 추후 깊이선량률, 빔측면도와 같은 선량분포에 대한 특성의 평가가 요구된다.

• 한국태양에너지학회 논문집
• /
• 제27권4호
• /
• pp.113-120
• /
• 2007

The 5kWt dish solar collector is designed and the preliminary performance test for this is carried out. The diameter of the parabolic dish is 3.2 m, and its focal length is 2 m. It consists of 10 small reflectors which have their own curvatures, and the effective reflecting area is $5.9\;m^2$, and the rim angle of the dish is $43.85^{\circ}$. The reflectivity of reflectors is 0.95, and the thermal capacity of the system is about 5 kW thermal. The aperture diameter of the cylindrical-shape receiver which is made of stainless steel is 100 mm, and the height is 210 mm. A quartz window is installed at the receiver aperture to minimize the convective heat loss and prevent air leakage. In order to increase the heat transfer area, porous materials (nickel-alloy) are inserted into the receiver. Air flows into the upper part of the receiver which is the opposite side of the aperture. After the air flows through the inside of the receiver, that goes out of the receiver through 3 exits which are located near the aperture. The volumetric flow rates of air are varied from 600 to 1200 L/min. The results show that the system efficiency and receiver efficiency increase as the volume flow rate increases.

• Food Science and Biotechnology
• /
• 제18권6호
• /
• pp.1379-1385
• /
• 2009

Quality changes of the slices processed from 'Niitaka' Asian pears (Pyrus pyrifolia) stored at $0^{\circ}C$ for up to 4 months under controlled atmosphere (CA, 1% $O_2+1%\;CO_2$) and normal air have been investigated for 4 days at $10^{\circ}C$. Respiration rate of the slices was retarded by pre-slicing storage for 4 months in CA. Electrolyte leakage was lower in the slices from pears stored for short-term than long-term and under CA than air. L and a values of the slices from whole pears stored under CA were maintained higher and lower, respectively as compared to the other. Levels of acetaldehyde and ethanol in the slices were increased by CA and long-term storage of whole pears. Content of ascorbic acid and counts of total aerobic microbes in the slices were not affected by storage conditions of whole pears. These results show that storage atmospheres and durations of whole pears affected quality changes of the slices and the conditions of pre-slicing storage should be considered as an important factor for optimizing fresh-cut procedures.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2001년도 추계학술대회 논문집 전기물성,응용부문
• /
• pp.195-197
• /
• 2001

The shorted-turn sensor for generator's field winding has been developed. The sensor, installed in the generator air-gap, senses the slot leakage flux of field winding and produces a voltage waveform proportional to the rate of change of the flux. For identification of reliability for sensor, a shorted-turn test was performed at the Seoinchon & Sininchon combined cycle power plant on gas turbine generator. This sensor will be used as a detecting of shorted-turn for generator's field winding.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제51권6호
• /
• pp.307-312
• /
• 2002

Inter-turn short circuits can have significant effects on a generator and its performance. The Inter-turn short circuits sensor for synchronous generator's field winding has been developed. The sensor, installed in the generator air-gap, senses the slot leakage flux of field winding and produces a voltage waveform proportional to the rate of change of the flux. For identification of reliability for sensor, a shorted- turn test was performed at the Seoinchon combined cycle power plant on gas turbine generator and stim turbine generator. This sensor will be used as a detecting of Inter-turn short circuits for synchronous generator's field winding.

• Journal of electromagnetic engineering and science
• /
• 제3권1호
• /
• pp.7-11
• /
• 2003

CDMA(code division multiple access) has very large peak to average power ratio(PAR) and behave as noise-like wide band digital signals with 1.2288 Mbps transmission rate. For signals with high PAR like CDMA, it is reasonable to prescribe occupied bandwidth(OBW) as average occupied bandwidth. Bandwidth measurements of CDMA signals at remote site are affected by co-channel and adjacent channel interference from adjacent CDMA base station, distortion of signal by fading effect, spurious emission and environment noises. In this study, we have compared OBW measurements in an on-air environment with those measured in a base station using adjacent channel leakage ratio(ACLR) as a reference measurement factor. As results of analysis, the OBW at ACLR$\geq$35 ㏈ shows nearly same statistical characteristics regardless of the measurement locations and environments.

• 연구논문집
• /
• 통권34호
• /
• pp.69-77
• /
• 2004

Electro-pneumatic servo valve is an electro-mechanical device which converts electric signals into a proper pneumatic flow rate or pressure. In order to improve the overall performance of pneumatic servo systems, electro-pneumatic servo valves are required, which have fast dynamic characteristics, no air leakage at a null point, and can be fabricated at a low-cost. The objective of this research is to design and to fabricate a new electro-pneumatic servo valve which satisfies the above-mentioned requirements. In order to design the mechanism of the servo valve optimally, the flow inside the valve depending upon the position of spool was analyzed variously, and on the basis of such analysis results, the valve mechanism, which was formed by combination of the spool and the sleeve, was designed and manufactured. Further, the performance of pneumatic servo valve has been verified through an overall performance test on the developed product.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2001년도 하계학술대회 논문집 C
• /
• pp.1765-1767
• /
• 2001

The shorted-turn sensor for generator's field winding has been developed. The sensor, installed in the generator air-gap, senses the slot leakage flux of field winding and produces a voltage waveform proportional to the rate of change of the flux. For identification of reliability for sensor, a shorted-turn test was performed at the Seoinchon combined cycle power plant on gas turbine generator. This sensor will be used as a detecting of shorted-turn for generator's field winding.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2008년도 추계학술대회A
• /
• pp.1210-1214
• /
• 2008

Electro-pneumatic servo valve is an electro-mechanical device which converts electric signal into pneumatic flow rate or pressure. In order to improve the overall performance of pneumatic servo systems, electro-pneumatic servo valves are required, which have fast dynamic characteristic, no air leakage at null, and can be fabricated at a low-cost. The first objective of this research is to design and fabricate a new electro-pneumatic servo valve which satisfies the above-mentioned requirements. In this paper, we has been modeled as a system consisting of coupled electro-mechanic and mechanical subsystems. The appropriateness of the model has been verified by simulation. The simulation model resolves the valve body motion and the solenoid current at high accuracy. Also, we are calculate the displacement of spool and computed results show winding currents, magnetic actuator force, flux density line, displacement, velocity, back EMF, eddy current etc.