• Elastomers and Composites
• /
• v.59 no.2
• /
• pp.64-72
• /
• 2024

As air pollution continues to increase owing to increasing traffic centered in urban areas, the tire industry is researching methods to reduce particulate matter. In this study, functionalized lithium butadiene rubber (F-LiBR) was applied to a natural rubber (NR)/butadiene rubber (BR) blend compound often used in truck bus radial (TBR) tire treads. The effect of the functional group that can react with carbon black (CB) in BR was investigated in terms of the dispersion of CB and the compound performance, including the generation of particulate matter. Compounds that were substituted with F-LiBR exhibited enhanced interaction with CB, resulting in excellent filler dispersion. Although F-LiBR exhibited lower crosslinking density and inferior abrasion resistance due to its high vinyl content, the compound with 30 phr of F-LiBR was advantageous in terms of its rolling resistance due to the excellent filler dispersion, which was also effective in reducing the amount of generated particulate matter (up to 56% reduction for PM_2.5, and 67% reduction for PM₁₀). The results confirmed the benefits of the introduction of functional groups into TBR tire tread compounds, which can aid in improving the fuel efficiency and reducing particulate matter generation.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.10 no.3
• /
• pp.195-202
• /
• 2006

Deterioration of sewer concrete is representative that biochemical corrosion according to the $H_2S$ has growth by inhabit sulfur-oxidzing bacteria because of special environment in sewer. But in case of domestic, fundamentally, sulfur-oxidzing bacteria could moderate development of repair material method is need because of corrosion prevent method is inconsideration with carry out to improve project. In this paper, after development of spread type antibiotic with antibio-metal, antibacterial performance about sulfur-oxidzing bacteria of antibiotic and tested to estimate fundamental properties of bonding strength, abrasion contents, contents of water absorption, contents of air permeability, carbonation depth, chloride ion penetration depth and chemical resistance of spread with antibiotic restorative mortar.

• Journal of Chest Surgery
• /
• v.43 no.4
• /
• pp.404-408
• /
• 2010

Background: Pleural symphysis is regarded as an important treatment option in reducing recurrence rates after surgical treatment of spontaneous pneumothorax. However, there is much debate over the best method for achieving pleural symphysis. We retrospectively compared apical pleurectomy (AP) with mechanical pleural abrasion (MPA). Material and Method: Between January 2000 and December 2007, 83 patients underwent video-assisted thoracoscopic surgery (VATS) for spontaneous pneumothorax. In addition to wedge resection of bullae, MPA was performed in 21 patients (group A) and AP in 62 patients (group B). Result: There were no significant differences in age, gender and site of pneumothorax between the two groups. Operative time was $97{\pm}44$ minutes in group A and $77{\pm}18$ minutes in group B (p>0.05). The mean amount of pleural drainage through the chest tube on the first postoperative day was $156{\pm}87 cc$ in group A and $147{\pm}87 cc$ in group B (p>0.05). There was no mortality or significant morbidity in all patients with the exception of reoperation for bleeding in two patients in group B. In the postoperative course, there were no statistical differences between the two groups in the rate of residual air space, air leak and indwelling time of chest tube, and hospital stay. Mean follow up time was $31.7{\pm}25.3$ months, and the recurrence rate of pneumothorax was 9.5% (2/21) in group A and 6.5% (4/62) in group B, without statistical significance. Conclusion: AP was no more advantageous than MPA in terms of operative time, postoperative course and prevention of recurrent pneumothorax. Therefore, complete resection of bullae and existence of residual bullae are more important factors in reducing the incidence of recurrent pneumothorax than pleural symphysis.

• The Journal of Korean Academy of Prosthodontics
• /
• v.53 no.4
• /
• pp.318-324
• /
• 2015

Purpose: This study compared shear bond strengths of five self-adhesive cements with phosphate monomer to zirconium oxide ceramic with and without airborn particle abrasion. Materials and methods: One hundred zirconia samples were air-abraded ($50{\mu}mAl_2O_3$). One hundred composite resin cylinders were fabricated. Composite cylinders were bonded to the zirconia samples with either Permacem 2.0 (P), $Clearfil^{TM}$ SA Luting (C), $Multilink^{(R)}$ Speed (M), $RelyX^{TM}$ U200 Automix (R), G-Cem $LinkAce^{TM}$ (G). All bonded specimens were stored in distilled water ($37^{\circ}C$) for 24 h and half of them were additionally aged by thermocycling ($5^{\circ}C$, $55^{\circ}C$, 5,000 times). The bonded specimens were loaded in shear force until fracture (1 mm/min) by using Universal Testing Machine (Model 4201, Instron Co, Canton, MA, USA). The failure sites were inspected under field-emission scanning electron microscopy. The data was analyzed with ANOVA, Tukey HSD post-hoc test and paired samples t-test ($\alpha$=.05). Results: Before and after thermocycling, $Multilink^{(R)}$ Speed (M) revealed higher shear-bond strength than the other cements. G-Cem $LinkAce^{TM}$ (G) showed significantly lower bond strengths after thermocycling than before treatment (P<.05), but the other groups were not significantly different (P>.05). Conclusion: Most self-adhesive cements with phosphate monomer showed high shear bond strength with zirconia ceramic and weren't influenced by thermocycling, so they seem to valuable to zirconia ceramic bonding.

• Journal of Chest Surgery
• /
• v.37 no.5
• /
• pp.438-443
• /
• 2004

Background : The treatment strategy for urinary spontaneous pneumothorax has progressively changed with the introduction of video-assisted thoracic surgery (VATS). Recently, we modified the strategy of primary spontaneous pneumothorax. If the patient had mild dyspnea and the lung was minimally collapsed, 2 mm thoracoscopic examination was performed. If no blob or bullae was inspected, the intrathoracic air was evacuated through the 2 mm thoracoscopic troca without closed thoracostomy, and if the blob and bullae was noted, the 10 mm thoracoscopic bullecotomy was carried out immediately and also application of fibrin glue was substituted for pleural abrasion. We compared the clinical outcomes of modified treatment strategy with conventional strategy in primary spontaneous pneumothorax. Material and Method: Patients were divided into four groups. Group I (n=21) underwent 2 mm thoracoscopic examination. Group II (n=68) underwent closed thoracostomy. Group III (n=56) underwent VATS and application of fibrin glue. Group IV (n=87) underwent VATS and pleural abrasion. The duration of chest tube drainage, the duration of hospitalization and the recurrence rate were compared between group I and group II and between group III and group IV. Result: Mean age, sex, location of pneumothorax were not different in all groups. In group I, the blob or bullae were existed in 12 patients, In remaining 9 patients, the bleb or bullae was not inspected. The mean duration of hospitalization in 9 patients were 2.4 $\pm$1.0 day and in group II were 3.9$\pm$2.1 day (p=0.014). There was 1 case of recurrence among the 9 patients in group I and 26 recurrences in group II (p=0.149). The mean duration of chest tube drainage were not difference in group III and IV (group III: 2.8$\pm$1.8 day, group IV: 3.0$\pm$2.5 day). The mean duration of hospitalization was shorter in group III than group IV (group III: 5,6$\pm$2.7 day, group IV: 1.3$\pm$3.3 day)(p=0.002). There was no recurrence in group III and 7 recurrences in group IV (p=0.043). Conclusion: Our modified treatment strategy of primary spontaneous peumothorax was effective in short hospital course and low recurrence rate.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.29 no.1
• /
• pp.69-79
• /
• 2013

The aim of this study was to evaluate the effect of surface conditioning on the shear bond strength of zirconium-oxide ceramic to resin cement. A total of 120 disk-shaped zirconium-oxide ceramic blocks(3-TZP, Kyoritsu, Tokyo, Japan) were treated as follows: (1) no treatment; (2) sandblasting with 110 ${\mu}m$ aluminum-oxide(Al2O3); (3) particles tribochemical silica coating(RocatecTM, 3M ESPE). Then zirconium-oxide ceramic blocks were divided into six groups(10 for each group) and bonded with resin cement(Rely X U-200, 3M ESPE). (1) No treatment / No treatment (2) No treatment / Sandblasting with 110 ${\mu}m$ aluminum-oxide particles (3) No treatment / Silica coating (4) Sandblasting with 110 ${\mu}m$ aluminum-oxide particles / Sandblasting with 110 ${\mu}m$ aluminum-oxide particles (5) Sandblasting with 110 ${\mu}m$ aluminum-oxide particles / Silica coating (6) Silica coating / Silica coating. Each group was tested in shear bond strengths by UTM. Data analysis included one-way analysis of variance(ANOVA) and the Tukey Honestly Significant Difference test (P=0.05). Group that bonded two silica coated specimen showed a highest bond strength(P<0.05). Two silica coated surface conditioning group and air-abrasion and silica coated surface conditioning group showed significantly difference with other groups(P<0.05). Other groups had no significantly difference each other. Within the limitation of this study, Surface conditioning with Rocatec treatment to each side of specimen provided the highest bond strength.

• The Journal of Korean Academy of Prosthodontics
• /
• v.48 no.4
• /
• pp.251-258
• /
• 2010

Purpose: To evaluate the effect of surface conditioning on the shear bond strength of zirconium-oxide ceramic to 4 luting agents. Materials and methods: A total of 120 diskshaped zirconium-oxide ceramic blocks (3Y-TZP, Kyoritsu, Japan) were treated as follows: (1) Sandblasting with $110\;{\mu}m$ aluminum-oxide ($Al_2O_3$) particles; (2) tribochemical silica coating (Rocatec) using $110\;{\mu}m$ $Al_2O_3$ particles modified by silica; (3) no treatment. Then zirconium-oxide ceramic blocks bonded with 4 luting cements (RelyX luting (3M ESPE), Maxcem (Kerr), Nexus3 (Kerr), Rely X Unicem (3M ESPE)). Each group was tested in shear bond strengths by UTM. A 1-way analysis of variance and 2-way analysis of variance was used to analyze the data ($\alpha$ = .05). Results: RelyX unicem in combination tribochemical silica-coating produced a highest bond strength (P < .05). Air abrasion group and Rocatec treatment groups resulted in significantly higher than no conditioning group (P < .05). RelyX Luting groups showed lower bond strength than other groups. There were significant differences among groups (P < .05). Conclusion: Within the limitation of this study, RelyX Unicem cement provided the highest bond strength and Rocatec treatment enhanced the bond strength.

• Journal of Chest Surgery
• /
• v.30 no.5
• /
• pp.512-516
• /
• 1997

We have experienced 66 cases of video assisted thoracic surgery(VATS) of spontaneous pneumothorax. The patients ranged in age from 1 Syears to 46years(mean age, 22.3years) and male patients were sixty three. The indications of video assisted thoracic surgery of spontaneous pneumothorax were recurrence, continuous air leakage, visible blabs on the chest X-ray & others. Infraoperative findings were as follows; blabs, pleural adhesion and pleural effusion. The operation was performed under general anesthesia wit double lumen endobronchial tube. Operative procedures included blebectomy and/or wedge resection of lung, vibramycin Pleurodesis with mechanical abrasion. In most cases, postoperative courses were uneventful and patients were discharged without significant complications. VATS provided the benefits of lesser postoperative pain, rapid recovery, short hospitalization, and smaller scar of wound. Conclusively VATS is a new interesting modality of surgical treatment of spontaneous pneumothorax and also can be extensively applicable in the diagnosis and treatment of other intrathoracic disease.

• Restorative Dentistry and Endodontics
• /
• v.33 no.2
• /
• pp.125-132
• /
• 2008

The purpose of this study is to compare the shear bond strength of repaired composite resin with different bonding agents and evaluate the effect of bonding agents on composite repair strength. Forty composite specimens (Z-250) were prepared and aged for 1 week by thermo cycling between 5 and $55^{\circ}C$ with a dwell time of 30s. After air abrasion with $50\;{\mu}m$ aluminum oxide, following different bonding agents were applied (n = 10); SB group: Scotchbond multipurpose adhesive (3 step Total-Etch system); XE group: Clearfil SE bond (2 step Self-Etch system); XP group: XP bond (2 step Total-Etch system); XE group: Xeno III (1 step Self-Etch system). After bonding procedure was completed, new composite resin (Z-250) was applied to the mold and cured. For control group. 10 specimens were prepared. Seven days after repair, shear bond strength was measured. Data was statistically analyzed using one-way ANOVA and Tukey's test (p<0.05). The means and standard deviations of shear bond strength (MPa ${\pm}$ S.D.) per group were as follows: SB group: 17.06; SE group: 19.10; XP group: 14.44; XE group: 13.57; Control Group: 19.40. No significant difference found in each group. Within the limit of this study, it was concluded that the different type of bonding system was not affect on the shear bond strength of repaired composite resin.

• Journal of Korean Dental Science
• /
• v.8 no.2
• /
• pp.82-88
• /
• 2015

Purpose: To evaluate the effect of light-curing on the immediate and delayed micro-shear bond strength (${\mu}SBS$) between yttria-tetragonal zirconia polycrystal (Y-TZP) ceramics and RelyX Ultimate when using Single Bond Universal (SBU). Materials and Methods: Y-TZP ceramic specimens were ground with #600-grit SiC paper. SBU was applied and RelyX Ultimate was mixed and placed on the Y-TZP surface. The specimens were divided into three groups depending on whether light curing was done after adhesive (SBU) and resin cement application: uncured after adhesive and uncured after resin cement application (UU); uncured after adhesive, but light cured after resin cement (UC); and light cured after adhesive and light cured resin cement (CC). The three groups were further divided depending on the timing of ${\mu}SBS$ testing: immediate at 24 hours (UUI, UCI, CCI) and delayed at 4 weeks (UUD, UCD, CCD). ${\mu}SBS$ was statistically analyzed using one-way ANOVA and Student-Newman-Keuls multiple comparison test (P<0.05). The surface of the fractured Y-TZP specimens was analyzed under a scanning electron microscope (SEM). Result: At 24 hours, ${\mu}SBS$ of UUI group ($8.60{\pm}2.06MPa$) was significantly lower than UCI group ($25.71{\pm}4.48MPa$) and CCI group ($29.54{\pm}3.62MPa$) (P<0.05). There was not any significant difference between UCI and CCI group (P>0.05). At 4 weeks, ${\mu}SBS$ of UUD group ($24.43{\pm}2.88MPa$) had significantly increased over time compared to UUI group (P<0.05). The SEM results showed mixed failure in UCI and CCI group, while UUI group showed adhesive failure. Conclusion: Light-curing of universal adhesive before or after application of RelyX Ultimate resin cement significantly improved the immediate ${\mu}SBS$ of resin cement to air-abrasion treated Y-TZP surface. After 4 weeks, the delayed ${\mu}SBS$ of the non-light curing group significantly improved to the level of light-cured groups.