• Corrosion Science and Technology
• /
• v.5 no.4
• /
• pp.141-148
• /
• 2006

The chemical composition and the semiconducting properties of the passive films formed on Alloy 690 in various film formation conditions were investigated by XPS, photocurrent measurement, and Mott-Schottky analysis. The XPS and photocurrent spectra showed that the passive films formed on Alloy 690 in pH 8.5 buffer solution at ambient temperature, in air at $400^{\circ}C$, and in PWR condition comprise $Cr_2O_3$, $Cr(OH)_3$, ${\gamma}-Fe_2O_3$, NiO, and $Ni(OH)_2$. The thermally grown oxide in air and the passive film formed at high potential (0.3 $V_{SCE}$) in pH 8.5 buffer solution were highly Cr-enriched, whereas the films formed in PWR condition and that formed at low potential (-0.3 $V_{SCE}$) in pH 8.5 buffer solution showed relatively high Ni content and low Cr content. The Mott-Schottky plots exhibited n-type semiconductivity, inferring that the semiconducting properties of the passive films formed on Alloy 690 in various film formation conditions are dominated by Cr-substituted ${\gamma}-Fe_2O_3$. The donor density, i.e., concentration of oxygen vacancy, was measured to be $1.2{\times}10^{21}{\sim}4.6{\times}10^{21}cm^{-3}$ and lowered with increase in the Cr content in the passive film.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.13 no.2
• /
• pp.99-112
• /
• 2015

In this study, laboratory test equipment was designed and installed to evaluate the thermal behavior of bentonite, which is used as a buffer in high-level waste disposal systems. The thermal analysis was conducted to verify the test results using ABAQUS, a finite element analysis code. In view of the seasonal changes seen during the test, the thermal behavior of bentonite with a temperature of outside air was evaluated. Of the cases examined, the results of the analysis model using stainless steel (Case 3) approximates to the test results, showing an error of about 1℃. The results of the thermal analysis into seasonal temperature distributions are consistent with trends seen in lab-test results. These analyses show that the effects of the thermal conductivity of the material surrounding the buffer and outside air temperature, are very important factors in the thermal behavior of bentonite. In the future, it is expected that a moisture saturation test of a bentonite buffer containing a heat source will be carried out. Therefore, the development of a numerical analysis model is required for the prediction and verification of the laboratory test results.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.08a
• /
• pp.377-377
• /
• 2011

Organic solar cells (OSCs) with low cost have been studied to apply on flexible substrate by solution process in low temperature [1]. In previous researches, conventional organic solar cell was composed of metal oxide anode, buffer layer such as PEDOT:PSS, photoactive layer, and metal cathode with low work function. In this structure, indium tin oxide (ITO) and Al was generally used as metal oxide anode and metal cathode, respectively. However, they showed poor reliability, because PEDOT:PSS was sensitive to moisture and air, and the low work function metal cathode was easily oxidized to air, resulting in decreased efficiency in half per day [2]. Inverted organic solar cells (IOSCs) using high work function metal and buffer layer replacing the PEDOT:PSS have focused as a solution in conventional organic solar cell. On the contrary to conventional OSCs, ZnO and TiO2 are required to be used as a buffer layer, since the ITO in IOSC is used as cathode to collect electrons and block holes. The ZnO is expected to be excellent electron transport layer (ETL), because the ZnO has the advantages of high electron mobility, stability in air, easy fabrication at room temperature, and UV absorption. In this study, the IOSCs based on poly [N-900-hepta-decanyl-2,7-carbazole-alt-5,5-(40,70-di-2-thienyl-20,10,30-benzothiadiazole)] (PCDTBT) : [6,6]-phenyl C71 butyric acid methyl ester (PC70BM) were fabricated with the ZnO electron-transport layer and MoO3 hole-transport layer. Thickness of the ZnO for electron-transport layer was controlled by rotation speed in spin-coating. The PCDTBT and PC70BM were mixed with a ratio of 1:2 as an active layer. As a result, the highest efficiency of 2.53% was achieved.

• Journal of Mushroom
• /
• v.11 no.4
• /
• pp.214-218
• /
• 2013

This study was carried out to find out suitable input method for air exchange about bottle cultivation of oyster mushroom. There was no difference of average temperature in cultivation room, but T1(direct introduction of outside air) was higher than T2(heat exchanger) and T3(air buffer) in the standard deviation. The ratio of cooling operating was the highest in August and in the descending order, T1 54%, T3 43%, T2 33%. At ratio of energy reduction, T2 and T3 were higher than T1. The operating ratio of heater was highest in January and in the descending order, T1 53%, T3 37%, T2 30%. At ratio of energy reduction(%), T2 and T3 were higher than T1 similar to result of cooling operating. Therefore there were largest in August about Cooling Degree-Hour and in January about Heating Degree-Hour. And fruitbody yields quality was excellent in T2 and T3 than T1. The suitable effective type of air exchange in oyster mushroom cultivation are heat exchange and air buffer system.

• Journal of Korean Society of Forest Science
• /
• v.87 no.2
• /
• pp.188-193
• /
• 1998

Soil pH change is an important factor which determines soil chemical properties. It is an indicator of the effect of urban environmental pollution on soils and plant growth. The objective of this study was to assess the effect of air pollution on the soil of Seoul urban forests during the course of the air pollution being dipersed toward suburb area. Study sites were divided into four sections of concentric circles with 5km interval. Soil samples were collected from A and B horizons in the urban forests, and analyzed for soil pH, soil buffer capacity, cation exchange capacity, and base saturation. Soil pH ranged from 3.96 to 5.08 for A horizon and from 4.10 to 5.25 for B horizon, which were not significantly different among the sections. However, there was a trend of soil pH lowered at the sections close to the urban center. Soil buffer capacity was lower at 0-5km and 5-10km sections compared to that at the outer sections. Cation exchange capacity and base saturation were not different significantly among the sections. Following the pattern of air pollutants being dispersed from urban center to suburb, soil acidification was observed at the urban forests in Seoul area. Low level of soil buffer capacity toward the urban center was an indicator of soil acidification at the urban forests.

• Journal of Power System Engineering
• /
• v.10 no.4
• /
• pp.165-171
• /
• 2006

An experiment to observe reduction of pressure fluctuation in the compressing system utilizing snubber has done. The experiment measured pressure at inlet and outlet of snubber. It used an air compressor as a model of hydrogen one. Snubber with buffer and snubber without buffer were used to get comprehensive comparison between both of that snubber. An analysis by using Fast Fourier Transform (FFT) method was conducted to verify working pressure frequency. With this method pure signal of static pressure was filtered from noisy signal. The experiment was run for several speeds of piston movement. It was controlled by adjustable frequency regulator that controled rotation of actuator motor. This was connected to the piston-reciprocating compressor with V-belt. From result obtained, the fluctuation was increasing proportionally when frequency of driver motor was increased.

• Journal of the Korean Society of Environmental Restoration Technology
• /
• v.6 no.3
• /
• pp.17-28
• /
• 2003

The objective of this study is to review and verify whether the functions and effect of roadside trees generally known in theory are actually realized in urban roads and how well they are performed if the function and effect are really realized. The study was conducted with a focus on air purification effect of roadside trees. The m헤r study result is as follows. First, calculation of air purification effect of roadside trees showed that it is minimal. However, 7.4 units of broad-leaved trees is necessary in order to purify $SO_2$ discharged by one passenger car and 1,803.3 trees to purify $NO_2$. Second, regarding pollutant absorption capacity, air pollutant absorption capacity increased as the number of rows planted gets higher (i.e., 2-row plantation absorbs pollutant better than I-row plantation). In particular, "2-row plantation + lower-level shrub + buffer green belt" was as eight times high as "I-row plantation" in absorption capacity. Third, out of 30 roads with over 8 lanes in 15 cities, only 33.3% or a total of ten roads in seven cities had a median strip. Out of these ten roads, nine roads were planted in a double-layer consisting forest trees, shrubs, ground plants (grass). Analysis showed that out of six tree species planted along these roads, about a half of them were weak to air pollution. Also, based on the outcome of this study, charging a "plantation due" when people purchase a new car, improving layout of roadside trees, and reinforcing plantation of air purification tree species when selecting tree species for roadside trees were proposed.

• Korean Journal of Animal Reproduction
• /
• v.22 no.3
• /
• pp.253-264
• /
• 1998

Porcine follicular oocyte, collected from antral follicles (2~5 mm in diameter) of gilt ovaries were matured in vitro porcine follicular fluid (pFF) with PMSG (pFF-PMSG) buffer with at 37$^{\circ}C$ under 5% CO2 in air their ability of maturation promoting factor (MPF), of GV and GVBD formation was examined followed during time after in vitro culture. Formation of second metaphase was observed in 57.6% and 71.2% of matured in with pFF-PMSG buffer to 45 and 50 hours after invitro. Porcine oocytes cultured in pFF-PMSG for various periods of up to 30 hours were stained with Hoechst-33342 and classified according to maturation before assaying. Histone H1 kinase (H1K) activity was assayed during meiotic maturation in porcine oocytes matured in pFF-PMSG buffer in vitro. In oocytes matured in pFF-PMSG, H1K activity was at the 30 hours after culture and increased about 15 fold than at the germinal vesicle stage with before at the cultured in vitro. This pattern is similar to those reported in non-mammalian species and su, pp.rts the concepts that H1K is ubiquitous in eukaryotes and controls the meiotic cell cycle in mammals. These results suggest that the maturation pFF-PMSG buffer used influences the fluctuation pattern of H1K activity and biological characteristics of porcine oocytes cultured in vitro.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.852-855
• /
• 2003

Gas-Assisted Injection Molding(GAIM) process, that can be used to provide a hollow shape in a molding, is a variant of the conventional injection molding process. GAIM has many advantages such as reduction of material, sink mark. warpage. and lower injection pressure. Thus, GAIM has been widely applied in the industry to make moldings with a hollow channel such as handles, TV frames and so on. On the other hand, GAIM has some disadvantages such as slow cooling time and flow marks. In the disadvantages, hot gas core causes slow cooling of a molding and the overflow. which is to prevent flow mark. is waste of materials. To solve these problems, we developed a new GAIM system that we called RGIM(Reverse Gas Injection Molding). The RGIM has two special units; one is the overflow buffer, which is used for reduction of a material, and the other tile air unit, which is used for faster cooling of a molding. We conducted an experiment and simulation to verify the efficiency of the RGIM system. Through experiments and simulation, we confirmed the effectively operating of the RGIM system and extracted the optimum process conditions.

• Corrosion Science and Technology
• /
• v.2 no.5
• /
• pp.212-218
• /
• 2003

Electronic properties of passive films formed on Ti at film formation potentials $(E_f)V_{SCE}$ in pH 8.5 buffer solution and in an artificial seawater were examined through the photocurrent measurement and Mott-Schottky analysis. The passive films formed on Ti in pH 8.5 buffer solution exhibited a n-type semiconductor with a band gap energys $(E_g);E_g^{n=2}=3.4$ eV for nondirect electron transition, and $E_g^{n=0.5}=3.7$ eV for direct electron transition. These band gap values were almost same as those for the passive films formed in artificial seawater, indicating that chloride ion ($Cl^-$ in solution did not affect the electronic structure of the passive film on Ti. $E_g$ for passive films formed on Ti were found to be greater than those ($E_g^{n=0.5}=3.1$ eV, $E_g^{n=2}=3.4$) for a thermal oxide film formed on Ti in air at $400^{\circ}C$. The disorder energy of passive film, determined from the absorption tail of photocurrent spectrum, was much greater than that for the thermal oxide film farmed on Ti in air at $400^{\circ}C$. The greater $E_g$ and the higher disorder energy for the passive film compared with those for the thermal oxide fIlm suggest that the passive film on Ti exhibited more disorded structure than the thermal oxide film. The donor density (about $2.4{\times}10^{20}cm^{-3}$) for the passive film formed in artificial seawater was greater than that (about $20{\times}10^{20}cm^{-3}$) formed in pH 8.5 buffer solution, indicating that $Cl^-$ increased the donor density for the passive film on Ti.