• Journal of the Korean Wood Science and Technology
• /
• v.2 no.2
• /
• pp.5-7
• /
• 1974

1. This study indicates that above the fiber saturation point the drying rate can be increased with increasing the velocity of the air circutation, i.e., the drying rate of sample boards is proportional to the air velocity, but below the fiber saturation point, the effect of the velocity of air circulation is very low as shown in Figs. 1 and 2. 2. Under the controlled temperature and humidity in the kiln, the more the sample boards have moisture, the higher drying rate of it can be obtained. In other words, this means that even though in the case of drying various moisture content of wood, at the final drying stage, approximately the same percentage of moisture content of wood can be secured by employing the higher velocity of air circulation. 3. This study shows that the rate of drying in kiln changes distinctly at the fiber saturation point, i, e., above the fiber saturation point, the drying curve shows concave aginst the X axsis, but below the fiber saturation point, in the range from 30 percent of moisture content to 20 percent of moisture content, the curve shows convex as shown in Fig. 3. As the drying progresses, however, the drying curve shows concave again below 20 percent of moisture content. This means that inflection point of drying curve may be located clearly at the fiber saturation point, i.e., 30 percent of moisture content. As mentioned above, the 30 percent of moisture content of wood at which the inflectional point appears can be recognized as a critical point, i. e., the fiber saturation point at which all free water was removed from wood. The existence of inflectional point indicates that the evaporation of hygroscopic water in a cell wall is more difficult than the evaporation of free water in a cell cavity and the minor space of cell wall. The convex curve in the range of moisture content from 30 percent to 20 percent means that the evaporation of capillary condensed water has a tendency of the same rates of drying approximately, but as approaching to the 20 percent of moisture, the transfusion of moisture from wood becomes difficult because of having less moisture in cell wall. Below 20 percent of moisture content, the drying curve shows concave again, which means that it is difficult to remove the moisture located nearer to the surface of cellulose molecules and the surface bound water. These relations were revealed in Fig. 4. In comparison AC curve which does not have the two inflection points with BD curve which has two inflection points, i.e., Band D, they are mentioned already, by existence of the inflection points, the curve BD shows that the change of drying rate in the interval from 20 percent of moisture content to 30 percent of moisture content is not greater than in the case of the curve AC in the same interval. At the inflection point of 30 percent of moisture content, it can be noticed that the changing of the drying rate is very conspicuous. This phenomenon also can be recognized, as it is noticed by the Fig. 3, the drying rate from green to 30 percent of moisture content is very great. But the inclination of the curve is very slow from 30 percent of moisture content to 20 percent of moisture content, i.e., the inclination of the curve becomes almost horizontal lines. Acknowledgments Gratitude is expressed to Fred E. Dickinson, Professor of 'Wood Technology, School of Natural Resources, University of Michigan, USA for his suggestion to carry out this study.

• The Korean Journal of Air & Space Law and Policy
• /
• v.30 no.2
• /
• pp.249-277
• /
• 2015

Regulation (EC) No 261/2004 ("Regulation") is a common rule on compensation and assistance to passengers in the event of denied boarding and of cancellation or long delay of flights. In some recent cases of European nations, passengers sued the air carrier in order to obtain monetary compensation under Article 7(1) of the Regulation. Some courts dismissed the actions on the grounds that, unlike denied boarding or cancellation of the flight, the Regulation provides no compensation in relation to delayed flights. However, Court of Justice of the European Union(CJEU) ruled that Regulation 261/2004 must be interpreted to mean that passengers whose flights are delayed have a right to compensation in cases when the loss of time is equivalent to, or is in excess of three hours - where the passengers eventually reached their final destination three hours or more later than the originally scheduled arrival time. It is true that a strict interpretation of the regulation would suggest that passengers whose flight has merely been delayed are not entitled to compensation. They should only be offered assistance in accordance with the Articles 6 and 9. Nevertheless, the Court recognized the same right to the same compensation for passengers of flights delayed by more than three hours as that explicitly provided for passengers of cancelled flights. On the one hand, the Court bases this ruling on the recitals of the Regulation, in which the legislature links the question of compensation to that of a long delay, while indicating that the Regulations seek to ensure a high level of protection for passengers regardless of whether they are denied boarding or their flight is cancelled or delayed. On the other hand, the Court interprets the relevant provisions of the Regulation in light of the general principle of equal treatment. Furthermore, the Court delivered a ruling that the loss of time inherent in a flight delay, which constitutes an inconvenience within the intention of Regulation No 261/2004 and which cannot be categorized as 'damage occasioned by delay' within the meaning of Article 19 of the Montreal Convention, cannot come within the scope of Article 29 of that convention. Consequently, under this view, the obligation under Regulation No 261/2004 intended to compensate passengers whose flights are subject to a long delay is in line with Article 29 of the Montreal Convention. Although the above interpretation of the Court can be a analogical interpretation, the progressive attitude of the Regulation and the view of Court forward to protect passengers' interest is a leading role in the area of international air passenger transportation. Hopefully, after the model of the positive support in Europe, Korea can establish a concrete rule for protecting passengers' right and interest.

• Strategy21
• /
• s.32
• /
• pp.5-35
• /
• 2013

The purpose of this thesis is to suggest how to plan ROK(Republic of Korea) Navy's strategy concerning to JOAC(Joint Operation Access Concept) and ASB(Air-Sea Battle) concept of US(United States) armed forces. Since 2006, US armed forces has been developing CONOPS(Concepts of Operations), JOAC & ASB. These concepts will not only affect security environment for Korea Peninsula and West Pacific Area, but also will be affected to ROK Navy's Strategy. Therefore, Korea Navy has to consider and review those concepts and should discuss the way to secure peace of Korea Peninsula. JOAC & ASB have been developed for securing operational access ability of US armed forces against enemy forces. A2/AD(Anti-Access, Area-Denial) is the strategy of possible enemy forces against US forces' approaching into the operation area and impede operations within area. US forces had to overcome enemy's A2/AD strategy in coming century to protect national interest and sustain global leadership. The main concept of JOAC & ASB is "Cross-domain Synergy", which means 'to eliminate duplicate and improve joint operability containing space and cyber operation area.' Korea Navy's acceptance of JOAC & ASB without any revising is not a rational choice. Without the amendment some problems can be occurred by the Korea navy's acceptance for the original version of JOAC & ASB. Those are "Missing differences of operation environment between Korea and US", "Impediment from neighbor nations, especially PRC (People's Republic of China)", and "Impediment inside from Korea armed forces". Therefore, Korea Navy has to evaluate and find out the way to solve for JOAC & ASB to apply for their strategy and minimise those possible problems above. This thesis is expected to be the solution.

• Journal of Environmental Impact Assessment
• /
• v.8 no.3
• /
• pp.35-47
• /
• 1999

The purpose of this study is to research the environmental amenity factors of a city to devise the strategies to preserve the factors. For this study, the area of Masan city in Korea was chosen, and questionnaires, field studies, and statistical researches were used. Based on the results, the research showed the city surveyed had expanded by 1,069%, and the population of the city had increased by 272% from 1970 to 1995. In the city-life environment, the traffic was not smooth and the streets were not safe. The number of cars increased by 40,797% from 1970 to 1995, but the total length of roads increased only by 333%. The number of traffic accidents increased by 850%. Buildings were not preserved or maintained and did not have any traditional value. Additionally, buildings were not harmonious with environmental surroundings. Land allocation for utilization was not mixed well with tradition. In relation with the surroundings, there were not enough spaces for old people, and parking spaces were limited. In the field of public policy and finance, economic support and fundamental facilities were not enough. The survey of the household environment and the neighborhood environment showed that the room temperature, sunshine, air condition, and space were medial in the household environment. Public social facilities and entertainment culture had the lowest quality in the neighborhood environment. The city-life environment, the neighborhood environment, and the household environment affected the quality of life in order. The above results showed that cities should be planned upon sustainable development with the idea of emphasizing ecological harmony and considering people first, that citizen should be planned upon sustainable life by the harmony between people and the environment. Cities should be places where all people can live together pleasantly and cooperate with each other.

• Proceedings of the KIPE Conference
• /
• 2003.11a
• /
• pp.214-217
• /
• 2003

The connectorless power supply system on that multi-contact causes confidence when the wiring reconstructed in the rear. As you see above, contact points between sets and indoor space cause inferior function of audio frequency so it needs to be eliminated. This paper explains the structure of connectorless power supply to supply the system with power crossing the air gap in the part of inductively in the connectorless power supply of both magnetic and electrical model. To get maximum output of electrical load, compensating capacitor compensates to show inter-inductance, lequeage-inductance reducing the track-inductance and access the conditions for resonance. At that time it accesses the maximum electric power. The small change of the value of compensating capacitor causes the changes of maximum electric power. Here the power electronics technology is used not only in the industrial machinery but also in the home appliances so the switching power supply is used to actualize the miniaturization, lightweight, and high efficiency. Generally the condenser input methods are widely used in the rectification circuit of switching power supply, but condenser input method generate great quantity of high frequency components because with this method the current flows in the power input filtering condenser only around value of peak of ac input voltage. To solve these problems, installation of power factor improve circuit on the front of filtering capacitence was considered. Several methods were suggested regarding, but the active filter method which makes smalliging and highly power factor possible are the produce main stream. IC for power factor improvement can be utilized by CMOS process proposing low power consumption. When the high power factor is considered seriously in the power factor improvement circuit, active filter method is selected. In the active filter method, the boost converter is used. Regarding this ·the boost converter is needed.

• Journal of Power System Engineering
• /
• v.3 no.3
• /
• pp.60-69
• /
• 1999

The noise and vibration sources of rotary compressor for room air-conditioner are pressure pulsation of compression process, cavity resonance of inner space, structural radiation noise of shell and impact noise of discharge valve. Among them, pressure pulsation is very important noise and vibration source. Because it transferred various kinds of noise and vibration like as mentioned above. In this reason, muffler and resonator are used in order to absorb and remove these noises. But an analytical prediction using acoustic analysis does not coincident with the experimental result. The difference between analysis and actual state is due to the assumption of analysis. This paper covered with new concept of muffler design based on the turbulence kinetic energy of flow by using CFD. From this analysis, it is possible to decide the best position of discharge port of muffler. Therefore $2{\sim}3dB$ noise reduction effect is acquired in rotary compressor of 5000 BTU grade. Also new approach of resonator design is suggested. From this study, the characteristics of resonator and surge hole (a kind of resonator without pipe length) are identified. The former is useful for pure tone noise (narrow frequency band), and the latter is effective for broad frequency band. This paper shows that it is very available to use 3 dimensional analysis of resonator in order to predict more exact tuning frequency. The result is proved by a lot of experiments. From combination of fluid analysis and acoustic analysis, up stream position is effective location of resonator concerning turbulence motion of fluid.

• Tunnel and Underground Space
• /
• v.24 no.4
• /
• pp.289-296
• /
• 2014

A simple analytical approach for stability assessment of underground storage caverns against ground uplift of overburden rock above the rock caverns for high pressurized fluid such as compressed air energy storage (CAES) and compressed natural gas (CNG) was developed. In the developed approach, we assumed that failure plane of the overburden is straight upward to ground surface, and factor of safety can be calculated from a limit equilibrium analysis in terms of this cylindrical shape failure model. The frictional resisting force on the failure plane was estimated by Hoek-Brown strength criterion which replaces with Mohr-Coulomb criterion such that both intact rock strength and rock mass conditions can be considered in the current approach. We carried out a parametric sensitivity analysis of strength parameters under various rock mass conditions and demonstrated that the factor of safety againt ground uplift was more sensitive to Mohr-Coulomb strength criterion rather than Hoek-Brown criterion.

• Fashion & Textile Research Journal
• /
• v.12 no.5
• /
• pp.633-641
• /
• 2010

The purpose of this study is to evaluate a new flight suit in bilateral ways; subjectively and objectively in the improvements of comfort and mobility. Seven healthy males at the age of twenties volunteered in this wearing test. They were over 177 cm in height and 92-95 cm in chest circumference, which satisfies the M95 Special' size described in the Korean Military Specifications and Standards. The subjective satisfaction was evaluated according to the criteria of ease of donning and doffing, fitness of wear, mobility, space between cloth and body, convenience in using restroom. Subjective satisfaction evaluation says that the best improvement of movement are neck circumference, chest breadth, armscye circumference, waist back length, crotch length, crotch height and body rise. According to the evaluation, improvements of mobility were conspicuous especially in parts of body like neck, breast, waist, back, and arms. When evaluating objective satisfaction, we measured a angle difference in a prescribed standard-grid on a photograph that picked up while the subject performed each motion in front of 10 cm-interval grid. As a result, the motion that had angle difference above 5 degrees were arm stretching and standing on single leg holding at forward or at his side. Bending necks and waist, crouching also had angle difference of over 5 degrees. The improvements are discussed from the viewpoint that the increased ease in parts of armscye circumference and crotch in new flight suit pattern.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2003.05a
• /
• pp.802-807
• /
• 2003

International Convention Center Jeju(ICCJ) was planed and built for accommodating a variety of conventional and exhibitional activities. For a better flexibility of operation, almost all rooms in ICCJ are designed to be subdivided Into a couple of small rooms with installation of movable partition walls. Architectural and acoustical design should be deliberatively and cooperatively undertaken to cope with such a complex condition. Conference hall, the largest room in ICCJ, has a capacity of 5000 seats who:1 used as a whole. It could be divided into 3 halls, one with 2000 pre-installed seats on slanted floor, up/down removable stage and its settings above, and the other 2 flat rooms with no seats installed. A devided hall with pre-installed seats and stage is designed for a multi-use auditorium. Almost all surfaces except ceilings adjacent to the stage are sound absorptively treated, in regard to extensive use of sound reinforcement systems. Its reverberation time 1.65 sec without audience, which is roughly correspond to 1.50 sec with fully occupied audience. When there is a need for a larger room, all the partition wail Is removed and the hall could be used as a whole. Exhibition hall is located in the first floor of ICCJ. Absorption and softness are needed for the hat 1 because exhibition behavior has something noisy features. Perforated MDF panels with porous materials and air space in the back groundare adopted for the walls. There are one large, two medium, and several small convention rooms in ICJJ. The room are also acoustically designed for maximum flexibility with no defects soundwisely.

• Journal of the Korea Institute of Building Construction
• /
• v.9 no.3
• /
• pp.95-101
• /
• 2009

Constructing large-scale mat foundation mass concrete is increasing for the stability of building structure, because a lot of high rise building are being built in order to make full use of limited space. However, It is of increasing concerns that because limited placing equipments, available job-site and systems for mass concete placement in construction field do not allow to place great quantity of concrete at the same time in large scale mat foundation, consistency between placement lift can not be secured. And also, it is likely to crack due to stress caused by the difference of hydration heat generation time. To find out the solution against above problems, this study is to reconfirm the performance of normal concrete designed by mix proportion and super retarding concrete. The Fundamental test shows what happens if low heat proportioning and control method of setting time are applied at the job-site of newly constructed high rise building. The test result show that slump flow of concrete has been somewhat increased as the target retarding time gets longer, while the air content has been slightly decreased but this is no great difference from normal concrete. The setting time shows to be retarded as target retarding time gets longer, the range of retarding time increases. It is necessary to increase the amount of mix of super retarding agent in the proportion ration by setting curing temperature high since outdoor curing is about 6 hours faster than standard curing, which means the temperature of the concrete will be higher than the temperature of the surrounding environment, due to its high hydration heat when applying in a construction site. The compressive strength of super retarding concrete appears to be lower than normal concrete due to the retarding action in the early stage. However, as the time goes by, the compressive strength gets higher, and by the 28th day the strength becomes the same or higher than normal concrete.