• Proceedings of the Korea Society for Energy Engineering kosee Conference
• /
• 1993.05a
• /
• pp.47-52
• /
• 1993

Recently, as exactly clean source, the research of photovoltaic power generation is undertaken actively and widely. In this paper, an auxiliary power supply system which is composed of photovoltaic generation and DC-DC boost chopper is described. This system in mainly for Air-conditioner appliances is which AC source is formed through rectifying circuit and without electrical storage battery. There exist two operating modes depending on the power quantity of the solar cells and the load. The control algorithm is discussed.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.6 no.1
• /
• pp.205-212
• /
• 1998

In this study, the effects of water vapor in inlet air on combustion efficiency, general performance, knock characteristics and emission gas concentration were investig- ated through the experiments of combustion and vibration analyses, emission gas analysis by changing water vapor quantity in inlet air with temperature and humidity auto control unit. With partial vapor pressure increase, the brake torque at wide open throttle status decreased and the average ignition delay angle increased, IMEP (indicated mean effective pressured using the integral and 3rd derivatives of filtered cylinder pressure as knock intensity, which matched well with the method of frequency power spectrum of block vibration signal. Water vapor in intake air had influence on the spark knock sensitivity. With the increase of water vapor content in intake air NOx emission was decreased and HC emission was increased.

• Proceedings of the Korean Society of Marine Engineers Conference
• /
• 2005.06a
• /
• pp.166-171
• /
• 2005

In this experiment study, to acquire elementary data for explaining to generate frost layer in the fin - tube evaporator. the experiment condition is to supply air on 0.3m/s, 0.6m/s, 0.9m/s and inlet air temperature is kept constantly $20^{\circ}C$, supplied air relative humidity is 70%, 80, 90%. And brine temperature in the copper tube was kept $-15^{\circ}C$ because, generally cooling temperature range is constantly $-15^{\circ}C$ in the heat exchanger for air conditioning system. in conclusion, through this experiment, we did compare with frost layer and frost quantity in each condition and examine these data

• Journal of the korean Society of Automotive Engineers
• /
• v.9 no.4
• /
• pp.41-49
• /
• 1987

It is an experimental study to improve the characteristics of combustion and exhaust emission gas in the gasoline engine. These characteristics are influenced by the fuel droplet size. To improve these characteristics, we make the ultrasonic atomization apparatus, and compare with the commercial carburetor. The results obtained are as follows: 1. Maximum atomization quantity is obtained by the vibrator of resonancy frequency 1.65MHz in the ultrasonic atomization apparatus. 2. With ultrasonic atomization apparatus, more than 99% of atomization rate can be obtained regardless of intake air temperature, velocity, and air-fuel ratio. 3. Atomization rate of the commercial carburetor increases with the air-fuel ratio and intake air temperature. 4. Difference of atomization rate between the ultrasonic atomization apparatus and the commercial carburetor increases with decreasing air-fuel ratio. 5. Droplet size is about 1-5.mu.m at the ultrasonic atomization apparatus, and 80-150.mu.m at the commercial carburetor, which indicates the ultrasonic atomization apparatus is excellent in atomization.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.6 no.6
• /
• pp.252-258
• /
• 1998

In a SI engine, it is necessary to control fuel quantity in accordance with intake air amount in order to reduce exhaust emission and improve the specific fuel consumption. Generally the map data is used for the vehicles with a SI engine. For the precise control of air-fuel ratio, the real time control method is recommended rather than the control method using map data. In this paper, we developed real time control system using microprocessor and IBM-PC, and applied it to the commercial SI engine. We got good results for air-fuel ratio under the idle condition.

• International Journal of Concrete Structures and Materials
• /
• v.19 no.1E
• /
• pp.41-48
• /
• 2007

Addition of latex to concrete is known to increase its durability and permeability. The purpose of this study is to analyze air void systems in latex-modified concretes using a reasonable and objective method of image analysis with such experimental variables as water-cement (w/c) ratios, latex contents (0%, 15%) and cement types (ordinary portland cement (OPC), high-early strength (HES) cement and very-early strength (VES) cement). The results are analyzed by spacing factor, air volume (content) after hardening, air void distribution and structure. Additionally, air void systems and permeability of latex-modified concrete (LMC) are compared by a correlation analysis. The results are as follows. The LMC of the same w/c ratio showed better air entraining (AE) effect than OPC with AE water reducer. The VES-LMC showed that the quantity of entrained air below $100{\mu}m$ increased more than four times. For the case of HES-LMC, microscopic entrained air between the range of 50 to $500{\mu}m$ increased greater than 7 times even in the absence of anti-foamer. Although spacing factor was measured rather low, the permeability of latex-modified concrete was good. It is construed that air void system does not have a considerable effect on the property of latex-modified concrete, but latex film (membrane) has a definite influence on the durability of LMC.

• Journal of Korea Port Economic Association
• /
• v.37 no.1
• /
• pp.71-85
• /
• 2021

A variety of methods have been proposed through a number of studies on sophisticated demand forecasting models that can reduce logistics costs. These studies mainly determine the applicable demand forecasting model based on the pattern of demand quantity and try to judge the accuracy of the model through statistical verification. Demand patterns can be broadly divided into regularity and irregularity. A regular pattern means that the order is regular and the order quantity is constant. In this case, predicting demand mainly through regression model or time series model was used. However, this demand is called "intermittent demand" when irregular and fluctuating amount of order quantity is large, and there is a high possibility of error in demand prediction with existing regression model or time series model. For items that show intermittent demand, predicting demand is mainly done using Croston or HOLTS. In this study, we analyze the demand patterns of various items of air cargo with intermittent patterns and apply the most appropriate model to predict and verify the demand. In this process, intermittent optimal demand forecasting model of air cargo is proposed by analyzing the fit of various models of air cargo by item and region.

• Tunnel and Underground Space
• /
• v.17 no.4
• /
• pp.248-254
• /
• 2007

Already, the air deck blasting method has been used to take many advantages of blasting. In the existing air deck blasting method, air deck is made usually on column charge. But in the case study, we analyzed about the effect of self supporting air tube which made air deck in column charge. As results of this case study, it was shown that blasting vibration was decreased about $20{\sim}26%$ and quantity of explosive was decreased about $10{\sim}20%$. Also, fragmentation was shown to be smaller than it of common blasting method.

• Journal of the Korean Society for Precision Engineering
• /
• v.18 no.9
• /
• pp.31-36
• /
• 2001

• Proceedings of the SAREK Conference
• /
• 2007.06a
• /
• pp.182-182
• /
• 2007