• Journal of the Korean Society of Food Science and Nutrition
• /
• v.43 no.6
• /
• pp.884-892
• /
• 2014

The purpose of this study was to investigate the drying characteristics and drying models of Ainsliaea acerifolia Sch. Bip. using far-infrared thin layer drying. Far-infrared thin layer drying test on Ainsliaea acerifolia Sch. Bip. was conducted at two air velocities of 0.6 and 0.8 m/sec, as well as three drying temperatures of 40, 45, and $50^{\circ}C$ respectively. The drying models were estimated using coefficient of determination and root mean square error. Drying characteristics were analyzed based on factors such as drying rate, leaf color changes, antioxidant activity, and contents of polyphenolics and flavonoids. The results revealed that increases in drying temperature and air velocity caused a reduction in drying time. The Thompson model was considered suitable for thin layer drying using far-infrared radiation for Ainsliaea accerifolia Sch. Bip. Greenness and yellowness values decreased and lightness values increased after far-infrared thin layer drying, and the color difference (${\Delta}E$) values at $40^{\circ}C$ were higher than those at $45^{\circ}C$ and $50^{\circ}C$. The antioxidant properties of Ainsliaea acerifolia Sch. Bip. decreased under all far-infrared thin layer drying conditions, and the highest polyphenolic content (37.9 mg/g), flavonoid content (22.7 mg/g), DPPH radical scavenging activity (32.5), and ABTS radical scavenging activity (31.1) were observed at a drying temperature of $40^{\circ}C$ with an air velocity of 0.8 m/sec.

• Progress in Medical Physics
• /
• v.15 no.4
• /
• pp.202-209
• /
• 2004

Flat panel based digital radiography (DR) systems have recently become useful and important in the field of diagnostic radiology. For DRs with amorphous silicon photosensors, CsI(TI) is normally used as the scintillator, which produces visible light corresponding to the absorbed radiation energy. The visible light photons are converted into electric signal in the amorphous silicon photodiodes which constitute a two dimensional array. In order to produce good quality images, detailed behaviors of DR detectors to radiation must be studied. The relationship between air exposure and the DR outputs has been investigated in many studies. But this relationship was investigated under the condition of the fixed tube voltage. In this study, we investigated the relationship between the DR outputs and X-ray in terms of the absorbed energy in the detector rather than the air exposure using SPEC-l8, an X-ray energy spectrum model. Measured exposure was compared with calculated exposure for obtaining the inherent filtration that is a important input variable of SPEC-l8. The absorbed energy in the detector was calculated using algorithm of calculating the absorbed energy in the material and pixel values of real images under various conditions was obtained. The characteristic curve was obtained using the relationship of two parameter and the results were verified using phantoms made of water and aluminum. The pixel values of the phantom image were estimated and compared with the characteristic curve under various conditions. It was found that the relationship between the DR outputs and the absorbed energy in the detector was almost linear. In a experiment using the phantoms, the estimated pixel values agreed with the characteristic curve, although the effect of scattered photons introduced some errors. However, effect of a scattered X-ray must be studied because it was not included in the calculation algorithm. The result of this study can provide useful information about a pre-processing of digital radiography.

• The Korean Journal of Nuclear Medicine Technology
• /
• v.16 no.1
• /
• pp.12-16
• /
• 2012

Purpose : In conventional PET image reconstruction, iterative reconstruction methods such as OSEM (Ordered Subsets Expectation Maximization) have now generally replaced traditional analytic methods such as filtered back-projection. This includes improvements in components of the system model geometry, fully 3D scatter and low noise randoms estimates. SharpIR algorithm is to improve PET image contrast to noise by incorporating information about the PET detector response into the 3D iterative reconstruction algorithm. The aim of this study is evaluation of SharpIR reconstruction method in PET/CT. Materials and Methods: For the measurement of detector response for the spatial resolution, a capillary tube was filled with FDG and scanned at varying distances from the iso-center (5, 10, 15, 20 cm). To measure image quality for contrast recovery, the NEMA IEC body phantom (Data Spectrum Corporation, Hillsborough, NC) with diameters of 1, 13, 17 and 22 for simulating hot and 28 and 37 mm for simulating cold lesions. A solution of 5.4 kBq/mL of $^{18}F$-FDG in water was used as a radioactive background obtaining a lesion of background ratio of 4.0. Images were reconstructed with VUE point HD and VUE point HD using SharpIR reconstruction algorithm. For the clinical evaluation, a whole body FDG scan acquired and to demonstrate contrast recovery, ROIs were drawn on a metabolic hot spot and also on a uniform region of the liver. Images were reconstructed with function of varying iteration number (1~10). Results: The result of increases axial distance from iso-center, full width at half maximum (FWHM) is also increasing in VUE point HD reconstruction image. Even showed an increasing distances constant FWHM. VUE point HD with SharpIR than VUE point HD showed improves contrast recovery in phantom and clinical study. Conclusion: By incorporating more information about the detector system response, the SharpIR algorithm improves the accuracy of underlying model used in VUE point HD. SharpIR algorithm improve spatial resolution for a line source in air, and improves contrast recovery at equivalent noise levels in phantoms and clinical studies. Therefore, SharpIR algorithm can be applied as through a longitudinal study will be useful in clinical.

• Korean Journal of Food Science and Technology
• /
• v.42 no.4
• /
• pp.494-501
• /
• 2010

The purpose of this study was to examine the presence of Bacillus cereus, aerobic bacteria and coliforms in the raw material of infant formulas and investigate the manufacturing process in terms of microbial safety. Among ten kinds of raw infant formula material samples (n=20), Bacillus cereus appeared in two (n=4). Aerobic bacteria were not detected in raw infant formula material or maximum 4.15 log CFU/g. Eleven species of aerobic bacteria were isolated and 76% of them were Sphingomonas paucimobilis, Pseudomonas fluorescens, Rhizobium radiobactor, or Stenotrophomonas maltophilia. A Pearson's correlation analysis revealed that the most influential factors for detecting Bacillus cereus were aerobic bacteria and coliforms. In other words, when the measured values of aerobic bacteria and coliforms were higher, the possibility that Bacillus cereus would appear increased. In a regression model to predict Bacillus cereus, the rate of appearance was correlated with aerobic bacteria and coliforms, and its contribution rate for effectiveness was 86%. Improving microbial quality control by pasteurization, spray dry, popping and extrusion resulted in a decrease in the numbers of Bacillus cereus, aerobic bacteria and coliforms in the raw materials. The results suggest that a hazard analysis and critical control point system might be effective for reducing microbiological contamination.

• Journal of Soil and Groundwater Environment
• /
• v.12 no.4
• /
• pp.60-71
• /
• 2007

Groundwater from public wells was monitored during one year with two month interval for hydrogeochemical parameters and chlorofluorocarbons (CFCs) as environmental tracers in Jeju Island. Concentrations of major cations and $SiO_2$ show variation less than 10% whereas $NO_3$ and dissolved oxygen (DO) showed larger variation though DO variation did not change oxic or suboxic condition. $NO_3$ concentration has no consistent seasonal pattern with the largest variation of 35%. Groundwater ages determined by CFCs became temporarily younger by 5 years in October for groundwater with ages of 15 to 25 years, which can be attributed to infiltrating water in rainy season. Compared to air temperature, groundwater temperature has much smaller variation with no phase difference, which can be accounted for by a two-component model consisting of infiltrating water from surface and deeper groundwater with negligible temperature variation. The relatively small variation in groundwater age and temperature indicates that groundwater recharge through fast flow-paths is much smaller compared with basal groundwater in terms of aquifer storage.

• Journal of Biosystems Engineering
• /
• v.41 no.1
• /
• pp.43-50
• /
• 2016

Purpose: The present study is aimed at examining the drying characteristics of sea tangle through a combination of microwave and far-infrared drying experiment and finding the optimal drying conditions. Methods: Sea tangle was cleaned and cut into fine pieces (5mm) before they were subjected to combinational drying by microwave and far-infrared ray. The amount of specimen per drying is 2 kg. The finely cut pieces of sea tangle were preheated in a microwave dryer for three different lengths of time (10, 15, and 20 min). Subsequently, they were dried using a far-infrared dryer at tow temperatures ($90^{\circ}C$ and $100^{\circ}C$) at an air velocity of 0.8 m/s until the final moisture content reduced to 10%. Results: Sea tangle dried under the condition of 20 min of preheating in the microwave dryer and drying at $100^{\circ}C$ by the far-infrared dryer. Of the drying models verified in this study, the logarithmic model showed high accuracy with the coefficient of determination $R^2>0.7825$ and RMSE<0.1095. The rehydration ratio of sea tangle was the highest (12.87 g water/g dry matter) under the condition of 15 min of preheating in the microwave dryer and drying at $100^{\circ}C$ by the far-infrared dryer. The energy consumption for the combination of microwave and far-infrared drying was the lowest (4.78 kJ/kg water) under the condition of 20 min of preheating in the microwave dryer and drying at $100^{\circ}C$ by the far-infrared dryer. Conclusions: Considering the drying time, discoloration during drying, rehydration ratio, and energy consumption for the drying of sea tangle, the optimal drying conditions for high-quality sea tangle are 15 min of preheating in a microwave dryer and drying at $100^{\circ}C$ by a far-infrared dryer.

• Korean Journal of Remote Sensing
• /
• v.33 no.6_1
• /
• pp.961-970
• /
• 2017

Despite of large demand for high spatial resolution products of aerosol properties from satellite remote sensing, it has been very difficult due to the weak signal by a single pixel and higher noise from clouds. In this study, aerosol retrieval algorithm with the high spatial resolution ($500m{\times}500m$) was developed using Geostationary Ocean Color Imager (GOCI) data during the Korea-US Air Quality (KORUS-AQ) period in May-June, 2016.Currently, conventional GOCI Yonsei aerosol retrieval(YAER) algorithm provides $6km{\times}6km$ spatial resolution product. The algorithm was tested for its best possible resolution of 500 m product based on GOCI YAER version 2 algorithm. With the new additional cloud masking, aerosol optical depth (AOD) is retrieved using the inversion method, aerosol model, and lookup table as in the GOCI YAER algorithm. In some cases, 500 m AOD shows consistent horizontal distribution and magnitude of AOD compared to the 6 km AOD. However, the 500 m AOD has more retrieved pixels than 6 km AOD because of its higher spatial resolution. As a result, the 500 m AOD exists around small clouds and shows finer features of AOD. To validate the accuracy of 500 m AOD, we used dataset from ground-based Aerosol Robotic Network (AERONET) sunphotometer over Korea. Even with the spatial resolution of 500 m, 500 m AOD shows the correlation coefficient of 0.76 against AERONET, and the ratio within Expected Error (EE) of 51.1%, which are comparable to the results of 6 km AOD.

• Journal of Environmental Health Sciences
• /
• v.31 no.5 s.86
• /
• pp.379-386
• /
• 2005

[ $PM_{10},\;PM_{2.5},\;CO_2\;and\;CO$ ] in driver cabins of subway line from 5 to 8 were monitored from 07:00 through 21:00 (or 19:30 or 20:00) on May. Driver cabin of subway line 7 showed the highest $PM_{10},\;PM_{2.5},\;CO_2\;and\;CO$ concentrations. General Linear Model indicated that subway line, subway location (ground and underground track) and running time (morning and afternoon) significantly influenced the concentrations of $PM_{10},\;PM_{2.5},\;CO_2\;and\;CO$ (p=0.000). Daily profile of $PM_{10},\;PM_{2.5},\;CO_2\;and\;CO$, expressed as an 30 minutes average, showed similar variation pattern over day period. These concentrations showed the highest concentrations between 07:00 and 09:00 of rush hour, slightly dropped and again rose slightly after 18:00. In correlation analysis, significant relations among $PM_{10},\;PM_{2.5},\;CO_2\;and\;CO$ were detected (p<0.01). In particular, correlation coefficient between $PM_{10}\;and\;PM_{2.5}$ was highly significant (r=0.884). Regression analysis also concluded that $PM_{10}$ concentration significantly explained 71.4% of variation of $PM_{2.5}$ concentration (p=0.000, $R^2=0.714$). Correlations by CO with $PM_{10}\;and\;PM_{2.5}$ were 0.451 and 0.520, which were higher than those by $CO_2$. Further study is needed to examine the sources of $PM_{2.5}$ and CO in subway and to compare pollutants concentration among subway lines.

• Journal of Food Hygiene and Safety
• /
• v.19 no.2
• /
• pp.74-83
• /
• 2004

Raw-fish food contains a lot of moisture and is a high-protein food. It is a first-stage processed food taking a lot of manual work. Therefore, it is classified as a PHF food, very liable to cause a bacterial food-poisoning. But its manufacturers are usually small-sized and a systematic sanitation management is difficult to expect. But the manufacturer participating in this study produces chilled fresh raw-fish food. Fish are sliced into two fillets, which are packaged under vacuum, kept and distributed in refrigerators, and sold within a day. It is a newly-developed kind of raw-fish food, and a more improved kind of raw-fish food making possible a systematic sanitation management. The HACCP (Hazard Analysis and Critical Control Point) is a systematic and continuous process-control method which is very efficient for controling food sanitation and reducing the expenses. A new HACCP model has been developed to be applied to a large-sized chilled fresh raw-fish food manufacturer. To ascertain its efficiency, the baterial examination was done to its workplace and products. The significance test was done on its data by "SPSS 12.0 for Window" and "Mann-Whitney U Test". The numbers of bacteria on its final products were significantly different in flatfish and porgy. The number of bacteria tended to decrease in each time-differential sampling (P＜.00l). The final food products showed no food-poisoning bacteria in all the time-differential tests and in all the samplings, which proves that the CCP of the HACCP system is under control. After the SSOP program was applied, no pathogenic bacteria were found in the work-place, and the kinds and numbers of bacteria decreased. The numbers of general bacteria and colon bacilli also showed a significant difference from those before the SSOP program in the filleting board (P＜.05), in the skinning board (P＜.0l), in the neck-removing knife (P＜.05), and in the filleting knife (P＜.01). The working equipments, periodically disinfected, also showed a significant difference in sanitary conditions (in the dehydrator, P＜.05). The number of bacteria found on the food-touching surface was within the standard (below 500/l00 cm$^2$) After the SSOP program was applied, the general bacteria and colon bacilli were not found. The quality of water used in the food processing was also within the standard. The numbers of bacteria falling from the air in the work-place were negligible in all the samplings (＜30CFU/l000ι). The staphylococci and fungi were not found.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.49 no.1
• /
• pp.1-10
• /
• 2012

Mobility and quality of service (QoS) are becoming the more important issues in wireless communications. The traditional Internet service is expanding into new access media and applications. Since wireless communication services are accompanied by frequent handovers at remote sites, scalable and fast handover has become a prerequisite for ubiquitous communication. In this paper, the differentiated service (Diffserv) model is deployed in heterogeneous proxy mobile IPv6 (PMIPv6) networks to satisfy the QoS guaranteed service and fast handover requirements. The operational procedures for QoS guaranteed global roaming are presented. In addition, QoS management and handover cost evaluation schemes based on a mobile host's movement scope are proposed. This paper analyzes the reduction in handover delay in a network-based localized mobility management framework. We propose and analyze a PMIPv6 optimized with a global mobile access gateway (G-MAG), which is a network-based entity, to further improve the handover performance in terms of handover delay while maintaining minimal signaling overhead in the air interface among converged heterogeneous wireless networks. The handover signaling procedures with host-based MIPv6 are compared with network-based proxy MIPv6 (PMIPv6) and fast PMIPv6 assisted by G-MAG to show how much handover delay reduction can be achieved. Analytical results show that the handover delay is significantly reduced.