• The KSFM Journal of Fluid Machinery
• /
• v.9 no.6 s.39
• /
• pp.45-53
• /
• 2006

Turbo-blower as an air supply system is one of the most important BOP (Balance of Plant) systems for FCV(Fuel Cell Vehicle). For generating and blowing compressed air, the motor of air blower consumes maximum 25% of net power, and fuel cell demands a clean air. In this study, turbo-blower supported by air foil bearings is introduced as the air supply system used by 80kW proton exchange membrane fuel systems. The turbo-blower is a turbo machine which operates at high speed, so air foil bearings suit their purpose as bearing elements. Analysis for confirming the stability and endurance is conducted. The rotordynamic stability was predicted using the numerical analysis of air foil bearings and it is verified through experimental works. In spite of various transient dynamic situation, the turbo-blower had stable performances. After the performance test, results are presented. The normal power of driving motor has about 1.6 kW with the 30,000 rpm operating range and the flow rate of air has maximum 160 SCFM. The test results show that the aerodymic performance and stability of turbo-blower are satisfied to the primary goals.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.10 no.3
• /
• pp.399-407
• /
• 1986

본 연구에서는 공기역학 탄성베어링의 설계에 필요한 기본이론에 대하여 고찰 하고 그의 신빙성을 그러한 베어링에 지지된 고속회전축의 진등측정을 통하여 검토하 고저 한다. 탄성베어링의 한 예로써 여러 개의 탄성박판이 겹쳐 저어널을 지지하는 겹판베어링(

• Tribology and Lubricants
• /
• v.18 no.3
• /
• pp.181-186
• /
• 2002

A numerical analysis is undertaken to show the influence of bearing design parameters on the load capacity of air lubricated spiral grooved thrust bearing. The governing equation derived from the mass balance is solved by the finite difference method. Optimal values for various design parameters are obtained to maximize the load capacity. The design parameters are the groove angle, the groove width ratio, the groove height ratio, and the seal ratio.

• International Journal of Precision Engineering and Manufacturing
• /
• v.8 no.2
• /
• pp.26-31
• /
• 2007

A novel scanning probe measurement system was developed to enable precise profile measurements of microaspheric surfaces. An air-bearing stylus with a microprobe was used to perform the surface profile scanning. The new system worked in a contact mode and had the capability of measuring micro-aspheric surfaces with large tilt angles and complex profiles. Due to limitations resulting from the contact mode, such as possible damage caused by the contact force and lateral resolution restrictions from the curvature of the probe tip, several system improvements were implemented. An air bearing was used to suspend the shaft of the probe to reduce the contact force, enabling fine adjustments of the contact force by changing the air pressure. The movement of the shaft was measured by a linear encoder with a scale attached to the actual shaft to avoid Abbe errors. A $50-{\mu}m-diameter$ glass sphere was bonded to the tip of the probe to improve the lateral resolution of the system. The maximum contact force of the probe was 10 mN. The shaft was capable of holding the probe continuously if the contact force was less than 40 mN, and the resolution of the probe could be as high as 10 nm, The performance of the new scanning probe measurement system was verified by experimental data.

• Journal of the Korean Society for Precision Engineering
• /
• v.30 no.12
• /
• pp.1321-1325
• /
• 2013

In this paper, we proposed an air bearing stage with active magnetic preloads in vertical directions compensating motion errors and attenuating vibrations to improve dynamic characteristics. This preloaded design gives simpler configuration of the stage, and active control of preload can be used for compensating motion errors by feedforward method. To improve dynamic characteristics, vibration of the table is monitored by an accelerometer, and controlled by a DSP based digital controller with integrator and band pass filters for suppressing roll and pitch vibration modes. The modes were evaluated by measuring frequency response functions, and compared with compensated responses. This showed effective results for suppressing poorly damped regenerative vibration of air bearings.

• Journal of the Korean Society for Precision Engineering
• /
• v.18 no.2
• /
• pp.119-125
• /
• 2001

This paper presents an experimental study on active control of self-excited vibration for a high speed turbomachinery. In order to suppress the self-excited vibration, it is necessary to actively control the air film pressure or the air film thickness. In this study, active pads are used to control the air film thickness. Active pads are supported by pivots containing piezoelectric actuators and their radial position can be actively controlled by applying voltage to the actuators. The transfer characteristics from actuator inputs to shaft vibration outputs are experimentally investigated. In a tilting-pad gas bearing (TPGB), a shaft is supported by the pressurized air film. Four gap sensors were used to measure the vibration of the shaft and PID was used in the feedback control of the shaft vibration. The experimental results show that the self-excited vibration of the rotor can be effectively suppressed if the PID controller gains are properly chosen. As a result we find that the feedback control is effective for suppressing the self-excited vibration of a rotor system using stack-type PZT actuators.

• Tribology and Lubricants
• /
• v.26 no.5
• /
• pp.283-290
• /
• 2010

In this study, the stiffness and damping coefficients of herringbone grooved air journal bearings are studied. A generalized coordinate transformation method to handle the complex geometry of incompressible fluid bearing is modified for compressible fluid. The modified equations are discretized by the base of finite difference method. A new computer program using Visual C++ language is developed. The load carrying capacity and stiffness and damping coefficients are calculated according to the design parameters like groove depth or the number of grooves and compared to that of plain air journal bearings.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.20 no.11
• /
• pp.1038-1045
• /
• 2010

The theory for a new electromagnetically biased combined radial and axial magnetic bearing is developed. This combined magnetic bearing uses two axial coils to provide the bias flux to the radial and axial air gaps of the combined bearing. One dimensional magnetic circuit model for this combined magnetic bearing is developed and analyzed such that flux densities and magnetic forces can be obtained. Three dimensional finite element model for the bearing is also developed and analyzed. Numerical analysis shows that the calculated magnetic forces from 1D model are well matched with those from the finite element model.

• Tribology and Lubricants
• /
• v.24 no.1
• /
• pp.34-43
• /
• 2008

In this paper, an actively controlled aerostatic bearing is studied to overcome the defects of air bearing such as low stiffness and damping coefficients. The actively controlled aerostatic bearing is composed of aerostatic bearings, non-contact type of displacement sensors, piezoelectric actuators and controllers. The cylindrical capacitance sensor (CCS) is used as the displacement sensor. The reason for using CCS instead of the commercial gap sensor is that it can give us the pure error motion of the spindle because it removes the roundness error or the geometric errors in the spindle. The controller is designed by the state space equation and quadratic optimal control theory. The characteristic data of the actively controlled aerostatic bearing system in the frequency domain are presented and the stiffness and damping coefficients of the bearing are mentioned. This paper shows the possibility to reduce the motion error up to 6000 rpm.

• Tribology and Lubricants
• /
• v.34 no.6
• /
• pp.300-306
• /
• 2018

In this study, the performance of foil thrust bearings was investigated by performing bearing take-off and load capacity tests, using an in-house designed and manufactured vertical bearing test rig. The mean take-off rotational speed and maximum load capacity of the bearing specimen were ~18,000 rpm and ~80 kPa, respectively. The vertical bearing test rig was observed to yield higher coefficients of friction and frictional torques than a horizontal bearing test rig under identical test conditions. This was a result of its structural characteristics, in that the bearing specimen is placed atop the thrust runner, which keeps it from being separated from the runner after the bearing take-off. In addition, bearing take-off was observed at a higher runner rotational speed as this structure keeps air from flowing between the top foil and runner surfaces, which requires a higher runner speed. The parallel alignment between the bearing specimen and runner surfaces can be maintained within a certain range more easily in a vertical test rig than in a horizontal test rig. Because of these advantages, Korean Industrial Standard, KS B 2060, recommends a vertical bearing test rig as the standard test device for foil thrust bearings.