• Computers and Concrete
• /
• v.33 no.3
• /
• pp.309-324
• /
• 2024

Internal curing, a widely used method for mitigating early-age shrinkage in concrete, also offers notable advantages for concrete durability. This paper explores the potential of internal curing by partial replacement of sand with fine lightweight aggregate for enhancing the behavior of high-performance concrete at elevated temperatures. Such a technique may prove economical and safe for the construction of skyscrapers, where explosive spalling of high-performance concrete in fire is a potential hazard. To reach this aim, the physico-mechanical features of internally cured high-strength concrete specimens, including mass loss, compressive strength, strain at peak stress, modulus of elasticity, stress-strain curve, toughness, and flexural strength, were investigated under different temperature exposures; and to predict some of these mechanical properties, a number of equations were proposed. Based on the experimental results, an advanced stress-strain model was proposed for internally cured high-performance concrete at different temperature levels, the results of which agreed well with the test data. It was observed that the replacement of 10% of sand with pre-wetted fine lightweight expanded clay aggregate (LECA) not only did not reduce the compressive strength at ambient temperature, but also prevented explosive spalling and could retain 20% of its ambient compressive strength after heating up to 800℃. It was then concluded that internal curing is an excellent method to enhance the performance of high-strength concrete at elevated temperatures.

• International Journal of Highway Engineering
• /
• v.10 no.3
• /
• pp.11-18
• /
• 2008

In recent, lots of researches for mechanical-empirical design concept for asphalt pavement are on going. AASHTO 2002 Design Guide in USA and KPRP(Korean Pavement Research Program) in Korea are under developing. In these programs, the mechanical properties of hot mix asphalt are a key role for design and analysis. Unfortunately, there is no proper database on the mechanical properties of hot mix asphalt, such as dynamic modulus. The use of dynamic modulus has couple of good advantages which is based on temperature, traffic loading and frequency on pavement. In this research, the verification of the relationship between maximum nominal aggregate size and dynamic modulus has been carried out. Also, test specimen size effect on dynamic modulus has been conducted. Considering the limitation of laboratory testing machine in Korea, test specimen with 100mm diameter and 150mm height is recommended for dynamic modulus test. Also, as the maximum nominal aggregate size increases, the dynamic modulus of hot mix asphalt increases.

• International Journal of Highway Engineering
• /
• v.15 no.2
• /
• pp.65-71
• /
• 2013

PURPOSES : The objective of this study is to evaluate the effect of physical characteristics of emulsion asphalt and aggregate on performance of chip seal pavements. METHODS : In order to evaluate the performance of chip seal materials, the sweep tests and Vialit Plate Shock tests were conducted on the mixtures with five emulsion asphalt binders and three aggregate types. The sweep tests was intended to investigate the change of bonding properties between emulsion asphalt and aggregate with curing time. The Vialit Plate Shock test was used to evaluate the bonding properties of chip seal materials at low temperatures. RESULTS : Results from sweep tests showed that polymer modified emulsion asphalt can reduce the curing time by 1.5 hour comparing with typical emulsion asphalt. It is also found that the Flakiness Index of aggregates and absorption rate of binder are the major factors affecting the bonding properties of chip seal materials. The Vialit Plate Shock test results showed that the average aggregate loss of CRS-2 is ten times higher than CRS-2P No.2 indicating that the use of polymer additives in emulsion asphalt can improve the performance of chip seal materials in low temperature region. CONCLUSIONS : The use of polymer in emulsion asphalt can decrease the curing time of chip seal materials and increase the bonding properties between aggregates and asphalt binder. It is also concluded that the lower Flakiness Index and absorption rate of aggregates can improve the performance of chip seal pavement.

• Journal of the Korea Safety Management & Science
• /
• v.12 no.3
• /
• pp.121-128
• /
• 2010

This is to show some basic data for introducing both circulated aggregate and recycled powder producing waste concrete. Standard-mixing design for 24MPa has been basically used and added and replaced normal aggregate with recycled powder made of waste concrete. In addition, polycarboxylate high-range water reducing agent has been used because recycled powder is missing adhesive strength and it is not compare with cement's adhesive strength. Compressive strength with powder mixture of 2%, 4%, 6%, 8%, and 10% has been decreased down to 80% of normal concrete material strength without recycled powder mixture. $200^{\circ}C$, $400^{\circ}C$ and $600^{\circ}C$ heated concrete were compressively tested in order to find out concrete strength resistant to high temperature. heat capacity was also tested, based on the expectancy of its low conductivity. In addition, thermal conduction test was tested in order to find out concrete insulation. According to this test, when concrete was tested by fire resistance, it using the circulation aggregate was same resulted by concrete using the natural aggregate. also, recycle powder was not effecting insulation performance. but it is fit to standard on concrete insulation of building law.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2018.05a
• /
• pp.58-59
• /
• 2018

In this study, firing experiments were carried out to confirm the foamability of the expansive shale collected from the local area. When expansive shales are subjected to high temperature heat, gas is generated inside and voids are formed. Due to this phenomenon, shale is used as a raw material for lightweight aggregate. Experiments were carried out with different plastic temperature and residence time to find the appropriate plastic temperature for this expansive shale. As a result, the higher the plastic temperature, the more the surface viscosity increased and the gas generated inside were retained. Resulting in a number of internal voids. However, even if the plastic temperature or the medium temperature is high, it is confirmed that sufficient gas is not generated when the residence time is shortened.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.12
• /
• pp.227-233
• /
• 2020

The demand for porous asphalt mixtures is increasing because it has a range of functions, such as reducing traffic accidents and traffic noise. On the other hand, its application is delayed due to concerns about durability. This study examined the effects of the maximum aggregate size, temperature, and porosity of an asphalt mixture on the durability. To this end, the durability measure was set to the Cantabro loss rate. Mixtures having the same porosity of 20% and the maximum aggregate diameters of 13 mm, 10 mm, and 8 mm were tested at 20℃ and -20℃. Mixtures containing 20% and 22% voids with the same material having the same diameter were tested. With 20% porosity, there was no significant difference in durability when there was a change in the maximum aggregate size. There was a significant difference between 20℃ and -20℃, but no significant difference in durability when there was a 2% difference between 20% and 22%. The significance of this study is that the durability was presented quantitatively by tests and statistical analysis. This research will help improve the durability of porous asphalt mixtures by evaluating the factors affecting the durability quantitatively.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.24 no.6
• /
• pp.261-267
• /
• 2014

In this study, we manufactured melting temperature controllable modified surfur (MS) and studied the properties of sulfur modified cement concrete (SMC). We investigated the effects of sulfur and pyridine content on melting temperature of MS. The reaction is confirmed by measuring Raman spectrophotoscopy. The SMC was produced at Water (W)/Cement (C) = 45 wt%, Sand (S)/Aggregate (A) = 45 wt% and 5, 10, 15 and 20 % of MS on the basis of conventional portland cement, respectively. And then physical properties such as compressive strength, splitting tensile strength and permeability of SMC were measured. As MS added, permeability was decreased, while strength and spalling properties were improved. To confirm the safety of MS and SMC, pyrolyzed gas chromatography (P-GC) and gas hazard test were conducted. The results showed that MS and SMC were relatively safe at an elevated temperature.

• Computers and Concrete
• /
• v.31 no.2
• /
• pp.111-121
• /
• 2023

The influence of material composition such as aggregate types, addition of supplementary cementitious materials as well as exposed temperature levels have significant impacts on concrete residual mechanical strength properties when exposed to elevated temperature. This study is based on data obtained from literature for fly ash blended concrete produced with natural and recycled concrete aggregates to efficiently develop prediction models for estimating its residual compressive strength after exposure to high temperatures. To achieve this, an extensive database that contains different mix proportions of fly ash blended concrete was gathered from published articles. The specific design variables considered were percentage replacement level of Recycled Concrete Aggregate (RCA) in the mix, fly ash content (FA), Water to Binder Ratio (W/B), and exposed Temperature level. Thereafter, a simplified mathematical equation for the prediction of concrete's residual compressive strength using Gene Expression Programming (GEP) was developed. The relative importance of each variable on the model outputs was also determined through global sensitivity analysis. The GEP model performance was validated using different statistical fitness formulas including R², MSE, RMSE, RAE, and MAE in which high R² values above 0.9 are obtained in both the training and validation phase. The low measured errors (e.g., mean square error and mean absolute error are in the range of 0.0160 - 0.0327 and 0.0912 - 0.1281 MPa, respectively) in the developed model also indicate high efficiency and accuracy of the model in predicting the residual compressive strength of fly ash blended concrete exposed to elevated temperatures.

• Journal of the Korean Ceramic Society
• /
• v.12 no.2
• /
• pp.3-9
• /
• 1975

The continuous grading method of pyrophyllite particles was adopted to prepare the refractories for ladle. The optimum conditions of fabrication adjusting the binders, the amount of water, the forming pressure and the firing temperature were investigated. The various properties, such as strength, density, porosity, thermal shock, corrosion resistance to slag were measured and compared with properties of ladle bricks presently used at local steel plants. The specimen studied in the present investigation showed a rather superior properties to theconventional product available locally.

• Magazine of RCR
• /
• v.4 no.3
• /
• pp.36-40
• /
• 2009