• Structural Engineering and Mechanics
• /
• v.5 no.5
• /
• pp.609-624
• /
• 1997

The optimization of cutouts in composite plates was investigated by implementing a procedure known as Evolutionary Structural Optimization. Perforations were introduced into a finite element mesh of the plate from which one or more cutouts of a predetermined size were evolved. In the examples presented, plates were rejected from around each evolving cutout based on a predefined rejection criterion. The limiting ply within each plate element around the cutout was determined based on the Tsai-Hill failure criterion. Finite element plates with values below the product of the average Tsai-Hill number and a rejection criterion were subsequently removed. This process was iterated until a steady state was reached and the rejection criterion was then incremented by an evolutionary rate and the above steps repeated until the desired cutout area was achieved. Various plates with differing lay-up and loading parameters were investigated to demonstrate the generality and robustness of this optimization procedure.

• Proceedings of the KSME Conference
• /
• 2004.04a
• /
• pp.1589-1594
• /
• 2004

A numerical analysis has been performed to give an understanding of the physics of a compressible base flow with mass bleed in a Mach 2.47 freestream. Axisymmetric, compressible mass-averaged Navier-Stokes equations are computed using a two-equation turbulence model, standard ${\kappa}-{\omega}$, and a fully implicit finite volume scheme. The mass bleed is characterized by the change in the mass flow rate of the bleed jet non-dimensionalized by the product of the base area and freestream mass flux. The result showing that there is an optimum bleed condition with maximum base pressure, leading to a minimum base drag, is clearly predicted and the validation with experimental data shows reasonable agreement.

• Advances in aircraft and spacecraft science
• /
• v.8 no.4
• /
• pp.331-344
• /
• 2021

Airframe internal and external specifications are the product of intensive intellectual efforts and technological breakthroughs distinguishing each aircraft manufacturer. Therefore, geometrical information characterizing aircraft primary aerodynamic surfaces remain classified. When attempting to model real aircraft, many members of the aeronautical community depend on their personal expertise and generic design principles to bypass the confidentiality obstacles and sketch real aircraft airfoils, which therefore vary for the same aircraft due to the different designers' initial assumptions. This paper presents a photogrammetric shape prediction method for deriving geometrical properties of real aircraft airframe by utilizing their publicly accessible static and dynamic visual content. The method is based on extracting the visually distinguishable curves at the fairing regions between aerodynamic surfaces and fuselage. Two case studies on B-29 and B-737 are presented showing how to approximate the sectional coordinates of their wing inboard airfoils and proving the good agreement between the geometrical and aerodynamic properties of the replicated airfoils to their original versions. Therefore, the paper provides a systematic reverse engineering approach that will enhance aircraft conceptual design and flight performance optimization studies.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.42 no.5
• /
• pp.406-414
• /
• 2014

In this paper, it is introduced characteristics of FMCW-type Radar Altimeter for KUH, and its defects occurred during ground/flight test in initial product phase. In addition, it is also described 'data/control flow model' based fault analysis results of S/W and processes of verifying improvement design through flight test as well as aircraft system integration test called MEP SIL. As a result of design improvement and verification, it is validated that settling the defects and improving not only safety but also capability of the KUH.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.48 no.9
• /
• pp.681-689
• /
• 2020

This paper presents methods and results of both flight test examining roll angle estimation performance of slowly rolling munition forced to spin in the air, and fabricating a replica of guided munition. Guided munition was deployed from multi rotor type UAV mother ship whose altitude and velocity was conveyed to it as initial state. Flight test scenario is composed of a sequence of munition drop(deployment), munition spin, roll angle estimation and stabilization. Munition was deployed from mother ship at around 200m high with horizontal velocity of 15m/s, and was made spun using internal reaction wheel. Performance analysis on roll angle estimation is provided in comparison with commercial aerospace graded GPS/INS. Moreover, several mechanisms that rotates munition using reaction wheel, and actual product that realizes one of them are introduced.

• International Journal of Aeronautical and Space Sciences
• /
• v.15 no.1
• /
• pp.54-62
• /
• 2014

The Air and Space Interoperability Council (ASIC) has adopted the European Defence Agency (EDA) process for inter-regulatory military airworthiness authority recognition. However, there are gaps in the application of this process to nations outside of the European Union. This paper proposes a model that can effectively map diverse technical airworthiness regulatory frameworks. This model, referred to as the Product-Behaviour-Process (PBP) Bow-Tie model, provides the systematic structure needed to represent and compare regulatory frameworks. The PBP Bow-Tie model identifies key points of difference that need to be addressed, during inter-agency recognition between the two regulatory authorities. With the intention to adopt global use of the EDA process, the proposed PBP Bow-Tie model can be used as a basis for the successful recognition of regulatory frameworks outside of the European Union. Iris plots produced from the implementation of this model are presented, and proposed as a suitable means of illustrating the outcome of an assessment, and of supporting the comparisons of results. A comparative analysis of the Australian Defence Force and New Zealand Defence Force airworthiness regulatory frameworks is used as a case study. The case study clearly illustrates the effectiveness of the model in discerning regulatory framework differences; moreover, it has offered an opportunity to explore the limitations of the Iris plot.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.35 no.7
• /
• pp.619-626
• /
• 2007

The analysis of the frictional energy of the rubber block with contact to the surface is necessary to study the wear for rubber. It is important to define the relationship of the frictional energy and wear, as the most theory of the wear of rubber product is based on the frictional energy of rubber block. To predict the life of the rubber block, the most of research has been focused on the use of the finite element analysis or the actual experiments which need the many time and expensive costs.Therefore, this research is achieved the successful results of the analysis to the frictional energy by analytic method. This frictional energy is function of the material properties, the shape of block, the vertical and horizontal load and the block moving speed. The analytical results are compared with the test results of this paper which can be used for the analysis of the friction behavior for the wear estimation of the rubber products.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.30 no.7
• /
• pp.1-10
• /
• 2002

Multidisciplinary Design Optimization (MDO) is a new design approach, which aims to reduce the design cycle and the development cost, while improving the performance of the product. In order to develop a framework software where the multidisciplinary design is possible, several methods about the analysis codes integration, the analysis and optimization process management, and the software architecture, are proposed in this study. Centralized DataBase Management System (DBMS) is adopted. Both the Dynamic Link Library(DLL) and the File Interface are suggested and implemented as analysis codes integration methods. To efficiently manage the optimization process and the data flow, the Graphic Programming approach is introduced. The proposed integration methods are verified by two test case examples: Simple house design example and the aircraft wing design problem using three dimensional Panel Code.

• International Journal of Aeronautical and Space Sciences
• /
• v.16 no.3
• /
• pp.418-424
• /
• 2015

The chemical response of energetic materials is analyzed in terms of 1) the thermal decomposition under the thermal stimulus and 2) the reactive flow upon the mechanical impact, both of which give rise to an exothermic thermal runaway or an explosion. The present study aims at building a set of chemical kinetics that can precisely model both thermal and impact initiation of a heavily aluminized cyclotrimethylene-trinitramine (RDX) which contains 35% of aluminum. For a thermal decomposition model, the differential scanning calorimetry (DSC) measurement is used together with the Friedman isoconversional method for defining the frequency factor and activation energy in the form of Arrhenius rate law that are extracted from the evolution of product mass fraction. As for modelling the impact response, a series of unconfined rate stick data are used to construct the size effect curve which represents the relationship between detonation velocity and inverse radius of the sample. For validation of the modeled results, a cook-off test and a pressure chamber test are used to compare the predicted chemical response of the aluminized RDX that is either thermally or mechanically loaded.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.37 no.9
• /
• pp.923-930
• /
• 2009

In this paper, we introduce a satellite conceptual design software which can be used for outlining a new satellite as well as for educational purpose. This software consists of three commercial tools: MATLAB, STK(Satellite Tool Kit), and Excel. The management of the design software is done by MATLAB which provides basic calculations, GUI(Graphical User Interface), Excel data base management, and STK control. STK, an orbital simulation software developed by AGI, takes a part of obtaining accurate orbital information of a satellite. Excel, a product of Microsoft, is used for the data base of previous satellites and for the saving place of temporary and final results of the software. The conceptual design of a satellite is to roughly estimate power system and mass. In the power system design, the sizes of solar array and battery are determined. Based on the database of existing satellites, we can estimate the subsystems's mass fraction of a target satellite. Design examples for Kompsat 1 and 2 are suggested for verification of the developed software.