• Journal of the Korea Society for Simulation
• /
• v.28 no.1
• /
• pp.49-56
• /
• 2019

In this study aerodynamic characteristics of guided gliding type ammunition were investigated by using a computational analysis and wind tunnel test. Missile DATCOM, a semi-empirical method, and a FLUENT, a computational fluid dynamics analysis program, were used for computational analysis. For a guided gliding type ammunition, aerodynamic characteristics were investigated by calculating lift force, drag force, pitching moment and etc. Aerodynamic characteristics of guided gliding type ammunition are completely different from those of conventional ammunition. The results obtained from the computer analysis are similar to those obtained from the wind tunnel test. Although the pitch moment values obtained by the semi-empirical method were slightly different from the wind tunnel test results, the overall computer analysis results showed trends and values similar to the test results. In this study, aerodynamic characteristics of guided gliding type ammunition were identified and it found that semi-empirical method can be applied to analyze the aerodynamic characteristic in the initial design of guided gliding ammunition.

• Proceedings of the KSR Conference
• /
• 2011.10a
• /
• pp.1320-1326
• /
• 2011

The maximum speed of high-speed rail is restricted to various factors such as track condition including slope and radius, tunnel and dynamic stability of vehicle. Among the various factors, traction effort and resistance to motion is principal and basic factor. In addition, at high speed over 300km/h, aerodynamic drag amounts up to 80% of resistance to motion, that it can be said that aerodynamic drag is the most important factor to decide the maximum speed of high-speed rail system. This paper deals with a measure to increase the maximum speed of high-speed train by reducing aerodynamic drag. The traction effort curve and resistance to motion curve of existing high-speed train under development has been employed to set up the target of aerodynamic drag reduction to reach up to 500km/h without modification traction system. In addition, the contribution of various sources of aerodynamic drag to total value has been analyzed and the strategy for implementation of aerodynamic drag reduction has been discussed based on the aerodynamic simulation results around the train using computational fluid dynamics.

• International Journal of Aeronautical and Space Sciences
• /
• v.16 no.2
• /
• pp.148-156
• /
• 2015

A continuous type side jet controller which has four nozzles with thrust control devices was considered. It is deployed to a missile for high maneuverability and fast controllability in the terminal guidance phase. However, it causes more complex aerodynamic jet interactions between the side jet and the supersonic free stream than does the conventional impulse type side jet with a small single thruster. In this paper, a numerical investigation of the jet interference effects for the missile equipped with a continuous type side jet thruster is presented. A three-dimensional flow field was simulated by using a commercial unstructured-based CFD solver. The numerical simulation method was validated through comparison with wind tunnel test results for the single jet. The method of defining jet direction for this type of side jet control to minimize simulation cases was also introduced. Flow fields investigation and jet interaction effects for various flow conditions, jet pressure ratios and defined jet direction conditions were performed. From the numerical simulation for the continuous type side jet, extensive aerodynamic interference data were obtained to construct an aerodynamic coefficients database for precise missile control.

• Journal of the Korea Society for Simulation
• /
• v.29 no.3
• /
• pp.49-55
• /
• 2020

A goal of improving projectile is to increasing achievable range. The shape of a projectile is generally selected on the basis of combined aerodynamics and structural considerations. The choice of body, nose and boattail shape has a large effect on aerodynamic design. One of the main design factors that affect projectile configuration is aerodynamic drag. The aerodynamic drag refers to the aerodynamic force that acts opposite to the relative motion of a projectile. An investigation was made to predict the effects of nose, boattail and body shapes on the aerodynamic characteristics of projectiles using a semi-empirical technique. A parametric study is conducted which includes different projectile geometry. Performance predictions of achievable range are conducted using a trajectory simulation model. The potential of extending the range of a projectile using optimization of projectile configuration is evaluated. The maximum range increase is achieved due to the combination of optimal body shapes.

• 한국전산유체공학회:학술대회논문집
• /
• 2007.10a
• /
• pp.264-271
• /
• 2007

The flow simulations around ducted-prop of tilt-duct aircraft were conducted in this study. For the investigation of aerodynamic characteristics of various configurations of duct, the axisymmetric flow calculation method combined with actuator disk model for prop were used. The rapid two-dimensional calculation and fast grid generation enable aerodynamic analysis for various duct configurations in a very short time and anticipated to active role in optimal configuration design of duct exposed to various flight modes. For the case of angle of attack or tilt angle, the three dimensional flow calculation is conducted using the three dimensional grid simply generated by just revolving the axisymmetric grid around center axis. Through the three dimensional calculation around duct, the aerodynamic effectiveness of duct as a lifting surface in airplane mode was investigated. The flow calculations around the control vane (wing) installed in the rear section of duct were conducted The aerodynamic data of wing were compared with the data of the ducts to evaluate the aerodynamic effectiveness of ducts.

• International Journal of Railway
• /
• v.4 no.3
• /
• pp.74-79
• /
• 2011

Recent years have witnessed speed up of moving vehicles such as high-speed of trains. Increase in speed entails concomitant increase in turbulent air flow which contributes toward increased aerodynamic noise. The proposed method for aerodynamic noise reduction is based on a biomimetic design of owl feather. The five morphological parameters of the owl feather are extracted from close observation, and simulation cases are constructed by applying design of experiments methodology. Swirling strength for each case is obtained through steady-state CFD analysis, and key morphological parameters that affect the turbulence are identified. Large eddy simulations (LES) are then performed on selected cases to predict the air turbulence. Different cases show varying vortex distributions which are expected to lead to varying aerodynamic noise levels.

• 한국전산유체공학회:학술대회논문집
• /
• 2003.08a
• /
• pp.120-125
• /
• 2003

Recently, lateral jet has been adopted as an effective control device for high maneuverable tactical missiles in supersonic regime. Aerodynamic interference caused by the lateral jet can be categorized into two phenomena : local interaction redistributing surface pressure near the jet exit region and downstream interaction affecting tail control effectiveness. As part of on-going research, this paper deals with the aerodynamic modeling to predict the variation of force and moment when lateral jet of is activated on the missile body. For this purpose, a series of numerical simulation has been performed and the results are presented. Using the information obtained by CFD, aerodynamic model of preliminary level has been constructed and is reviewed. Some relevant comparison with wind tunnel tests are presented.

• Journal of Aerospace System Engineering
• /
• v.9 no.4
• /
• pp.1-7
• /
• 2015

The purpose of this research is to develop co-simulation methodology of codes developed in different modeling and simulation environment. We develop aerodynamic FMU(Functional Mock-up Unit) meeting FMI(Functional Mock-up Interface) specification version2 utilizing Legacy FORTRAN aerodynamic code based on unsteady vortex lattice method. It is concluded that making FMU is possible utilizing Legacy code made in any language which can be compiled and linked with object in FMI API coded in C language. This paper explains QTronic's method of using FMU SDK(Software Development Kit) and suggestion for using FORTRAN properly. Finally, we make articulated rotor/aerodynamics co-simulation by integrating aerodynamics FMU and rotor FMU developed by Modelica.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.11a
• /
• pp.184.1-184.1
• /
• 2010

Floating wind turbines have been suggested as a feasible solution for going further offshore into deeper waters. However, floating platforms cause additional unsteady motions induced by wind and wave conditions, so that it is difficult to predict annual energy output of wind turbines by using conventional power prediction method. That is because sectional inflow condition on a rotor plane is varied by unsteady motion of floating platforms. Therefore, aerodynamic simulation using Vortex Lattice Method(VLM) were used to investigate the influence of motion on the aerodynamic performance of a floating offshore wind turbine. Simulation with individual motion of offshore platform were compared to the case of onshore platform and carried out according to the wave height and the wave angular frequency.

• Journal of computational fluids engineering
• /
• v.19 no.1
• /
• pp.41-46
• /
• 2014

The aerodynamic drag of high-speed train has been calculated and the effect of bogie side fairing on the aerodynamic drag has been investigated. Computational Fluid Dynamics (CFD) simulation based on steady-state 3 dimensional Navier-Stokes equation has been conducted employing FLUENT 12 and the aerodynamic model of HEMU-430x, the Korean next generation high-speed train under development has been built using GAMBIT 2.4.6. Three types of bogie side fairing configuration, the proto-type without fairing, half-covered fairing to avoid the interference with the bogie frame and full-covered fairing have been adopted to the train model to compare the drag reduction effects of the bogie side fairing configurations and the numerical results yields that the bogie side fairing can reduce the aerodynamic drag of the 6-car trainset up to 7.8%. The aerodynamic drag coefficient of each vehicle as well as the flow structures around the bogie system have also been examined to analyze the reason and mechanism of the drag reduction by bogie side fairing.