• Journal of Advanced Marine Engineering and Technology
• /
• v.27 no.3
• /
• pp.421-428
• /
• 2003

The aerodynamic characteristics of the Wells turbine for wave energy conversion have been investigated by the numerical simulation to reproduce hysteretic behaviors. The pressure distributions on the suction surface of the blade were investigated to find out the cause of the hysteretic mechanism. The results have shown that the hysteretic behavior is associated with streamwise vertical flow appearing near the suction surface and become more obvious. as the tip clearance and solidity change. Also it has shown that such phenomena occur due to different behaviors of wakes in the accelerating and decelerating flow process. The CFD analysis shows a good agreement with experimental results.

• Journal of the Korean Society for Aviation and Aeronautics
• /
• v.15 no.3
• /
• pp.33-45
• /
• 2007

The collision avoidance maneuver flight simulation for tilt rotor unmanned aerial vehicle was performed by time-accurate numerical integration method based on wind tunnel test data. Five representative collision avoidance maneuvers were simulated under constraints of aerodynamic stall, propulsion power, structural load, and control actuator capability. The collision avoidance performances of the maneuvers were compared by the computed collision avoidance times. The sensitivities of initial flight speed and collision zone shape on the collision avoidance time were investigated. From these results, it was found that the moderate pull-up turn maneuver defined using moderate pitch and maximum roll controls within simulation constraints is the most robust and efficient collision avoidance maneuver under the various flight speeds and collision object shapes in the tilt rotor UAV applications.

• Journal of the Korean Society for Aviation and Aeronautics
• /
• v.21 no.2
• /
• pp.1-6
• /
• 2013

In high-speed vehicle, selection of fuel, configuration of components and cooling system are required to solve the heating issue by aerodynamic heating and inner combustion process. This subsystem consists of fuel tank, supply pump, various control valve, heat exchanger, including reactor, connecting line, adiabatic structures and insulations. In this paper, applicable fuel property is considered at flight characteristic of hypersonic vehicles. In this regard, current state of fuel/cooling system technology is identified.

• International Journal of Air-Conditioning and Refrigeration
• /
• v.13 no.1
• /
• pp.31-43
• /
• 2005

The new HVAC system is developed to lower the conveyance energy and building height using IAV(Increasing Air Volume) technique. IAV units which are equipped in each zone carry out air-conditioning and supply fresh air by induction of outdoor air in main duct. The design program which decides size of OAHU and IAV unit according to air conditioning load and fresh air demand of each zone is presented. The control system is developed to operate efficiently HVAC system and IAV unit, so that individual zone operation and well-deal with partial load and IAQ problem are possible. The new system is investigated in model building and makes more profit in conveyance energy. size of air conditioning facilities room and building height than VAV system. But in construction cost it is worse by about 15 percentage.

• 한국전산유체공학회:학술대회논문집
• /
• 2002.05a
• /
• pp.53-58
• /
• 2002

A three-dimensional incompressible Navier-Stokes solver is developed for the flow analysis around Micro Air Vehicle(MAV) designed by MACDL(Micro Aerodynamic Control and Design Lab), Seoul National Univ., Validations of this solver are presented for two cases, first flow over the circular cylinder with infinite length, second flow over infinite wing with wing section, E387 airfoil. Simultaneously, Wind Tunnel test is performed with Flatform Wire type sir-component balance and model designed by MACDL. The numerical results are also examined through comparison with experimental data.

• Journal of computational fluids engineering
• /
• v.14 no.4
• /
• pp.48-55
• /
• 2009

In this study, roll lock-in phenomena of freely spinning tailfins were investigated by a CFD code. To analyze a motion of freely spinning tailfins, this research use a Chimera method, an Euler code and a 6 degrees of freedom analysis. The numerical results of aerodynamic characteristics and roll rates of a canard-controlled missile with freely spinning tailfins show a good agreement with wind tunnel test results. Using the roll rates calculation result of freely spinning tailfins, roll lock-in phenomena is confirmed. Roll lock-in phenomena and Roll lock-in states can be predicted through effects of the induced vortex of the canards control and the analysis of the rolling moments of tailfins due to the bank angle.

• Journal of Advanced Marine Engineering and Technology
• /
• v.22 no.4
• /
• pp.451-459
• /
• 1998

THe influence of internal acoustic exitation through a square prism on the turbulent wake flow characteristics was investigated. The intermediate wake region where is about ten times the respective length of the body was experimentally investigated using a conditional phase average technique. At first the static base pressures of square prism and the shedding frequencies have been measured at various internal acoustic exciation frequencies. The experiment were performed under the four cases of internal acoustic excitation frequencies 0Hz 30Hz($St_e$=0.09) 65Hz($St_e$=0.20) 120Hz($St_e$=0.38) And velocity vector fields were presented and discussed. The influence of acoustic exvitation frequencies on the structure of intermediate turbulent wake region is evident. As the internal acoustic frequency increased shedding frequency gradually increased and aerodynamic force decreased. Also it was found that the vortex shedding occurs dratically well and shedding frequency reached nearly the same value as the internal acoustic frequency. but above Strouhal number 0.3 the influence disappeared.

• Proceedings of the KSME Conference
• /
• 2004.04a
• /
• pp.1993-1998
• /
• 2004

The present study was carried out to develop highly efficient RC ornithopter 'Songgolmae' powered by motor and battery. Designed electric ornithopter weighs 277 grams and has 3 channels radio control. 1t runs on an electric motor by a lithium polymer battery and has a gear ratio of about $75{\sim}95$ to 1 to flap its 88 cm wingspan. The aerodynamic performance of the ornithopter, applied to a flapping motion only, was validated by flight tests. Flight times have exceeded 23 minutes until the battery was used up. The flight test results indicate that the ornithopter developed here has sufficient thrust to propel itself in a forward flight. From the economical point of view and the handling of the RC ornithopter, it can be said that the developed robot ornithopter is an effective RC ornithopter. This radio controlled ornithopter flies its way high into the sky just like a real bird flies.

• Aerospace Engineering and Technology
• /
• v.1 no.2
• /
• pp.11-18
• /
• 2002

The structural load analysis of 50m class airship was performed. The airship maneuver condition for analysis was defined. Aerodynamic, inertia and buoyance models were built. Control surface motion to make defined maneuver condition were calculated. Load factors, load, shear and bending moment envelops were developed for full airship and tailwing. Gondola design loads were developed.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.56 no.1
• /
• pp.6-12
• /
• 2007

In this paper, an robust adaptive backstepping controller is proposed for the speed control of separately excited DC motor in pure electric vehicles. A general electric drive train of PEV is conceptually rearrange to major subsystems as electric propulsion, energy source, and auxiliary subsystem and the load torque is modeled by considering the aerodynamic, rolling resistance and grading resistance. Armature and field resistance, damping coefficient and load torque are considered as uncertainties and noise generated at applying load torque to motor is also considered. It shows that the backstepping algorithm can be used to solve the problems of nonlinear system very well and robust controller can be designed without the variation of adaptive law. Simulation results are provided to demonstrate the effectiveness of the proposed controller.