• 유체기계공업학회:학술대회논문집
• /
• 2001.11a
• /
• pp.281-286
• /
• 2001

The radial turbine has been successfully applied to the systems which request relatively small output compared with the axial turbine, and has low manufacturing cost due to it's small size and simple structure. Recently, the researches on the development and the efficiency maximization of the radial turbine are in progress corresponding with the trend toward miniaturization in turbo machinery and the development of small dispersed power generation systems. The radial turbine is to be applied to our turbo refrigerator of which engine speed is 26,000 rpm and turbine efficiency is $88\%$. Also, as a heat exchanger is accepted instead of a combustor in our turbo refrigerator, the design of radial turbine has been performed to be appropriate to the circumstance of low temperature air, not high temperature combustor gas, into the turbine inlet . This radial turbine is being developed in consideration with not only the aero-dynamic performance but also the simplification of manufacturing and integration, and the durability at operating condition. This paper refer to the performance evaluation about the radial turbine design by comparison with consulting from Russia and the our evaluation about various design factors which are considered in aero-dynamic design process.

• Journal of Power System Engineering
• /
• v.21 no.3
• /
• pp.85-92
• /
• 2017

Global air traffic is forecast to grow at an average annual rate of around 5% in the next 20 years. The continuous growth of air traffic and raised environmental awareness put increasing pressure on aero engine manufacturers to reduce fuel burn and emissions. NEWAC are a new integrated program of the European Union with focus on innovative core engine concepts to achieve this problem. In this paper, Within NEWAC, active core engine configurations will be investigated. the investigation is focused on the optimal design of the CAC heat exchanger for active core. For optimal design of he CAC heat exchanger, the HTFS of basic design of heat exchanger are analyzed so as to proceed an optimization routines based on Response Surface Method(RSM) and Design of Experiment(DOE). As a result, CAC heat exchanger optimized by 1.0314 lb/s mass flow rate and 3.9058 mm TP of tube layout and 206.8181 mm height of heat exchanger and 918 tube number for heat transfer and pressure drop. We confirm the design optimization using RSM and DOE is useful on complex structure of heat exchanger.

• International Journal of Aeronautical and Space Sciences
• /
• v.15 no.2
• /
• pp.123-137
• /
• 2014

The aviation gas turbine is composed of many expensive and highly precise parts and operated in high pressure and temperature gas. When breakdown or performance deterioration occurs due to the hostile environment and component degradation, it severely influences the aircraft operation. Recently to minimize this problem the third generation of predictive maintenance known as condition based maintenance has been developed. This method not only monitors the engine condition and diagnoses the engine faults but also gives proper maintenance advice. Therefore it can maximize the availability and minimize the maintenance cost. The advanced gas turbine health monitoring method is classified into model based diagnosis (such as observers, parity equations, parameter estimation and Gas Path Analysis (GPA)) and soft computing diagnosis (such as expert system, fuzzy logic, Neural Networks (NNs) and Genetic Algorithms (GA)). The overview shows an introduction, advantages, and disadvantages of each advanced engine health monitoring method. In addition, some practical gas turbine health monitoring application examples using the GPA methods and the artificial intelligent methods including fuzzy logic, NNs and GA developed by the author are presented.

• Journal of Aerospace System Engineering
• /
• v.14 no.3
• /
• pp.60-68
• /
• 2020

If a broken blade in the aircraft engine penetrates the casing and ejects outside the aircraft, it will impact the fuselage, threatening the safety of the passengers. Thus, the development of a engine case should be certified for stability evaluation by the Aviation Administration. In this paper, we investigated the requirements and development technology for the containment certification of the engine casing necessary for the independent engine development in the country. An experimental/analytical method has been identified to summarize the contact safety requirements presented by the U.S. and European aviation agencies to verify the containment of debris in the casing corresponding to this certification. Also, we analyzed recent research on the containment casing and verification methods in casing development.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.23 no.1
• /
• pp.124-131
• /
• 2019

A design study of gas turbine engine simulation duct was conducted to investigate the operating characteristics and control gain tunning of the Altitude Engine Test Facility(AETF). The simulation duct design involved testing variable spike nozzle and ISO standard choking nozzle to verify the measurements such as mass flow rate and thrust. The simulation duct air flow area was designed to satisfy Ma 0.4 at the aerodynamic interface plane(AIP) at engine design condition. The test conditions for verifying the AETF controls and measurement devices were deduced from 1D analysis and CFD calculation results. The spike-cone driving part was designed to withstand the applied aero-load, and satisfy the axial traversing speed of 10 mm/s at whole operation envelops.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.47 no.12
• /
• pp.848-855
• /
• 2019

Eco-friendly gas turbine combustors are getting attention due to emission regulations. Swirler is important design factor for flame stability and flashback inside the combustor. Design methods of the axial swirler and the radial swirler were discussed and the suitability of the swirl number calculation considering the geometric design variables and the flow loss was examined in the radial swirl for gas turbine combustor. The swirl number of flow was calculated by computational fluid dynamics and compared with swirl number according to each design method.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.8
• /
• pp.279-285
• /
• 2019

Transverse vibrations of a ship's aft end and deckhouse are mainly induced by transverse exciting forces from the main engine. Resonance should be avoided in the initial design stages when there is a prediction of resonance between the main engine and transverse modes of the deckhouse. Estimates of frequencies for resonance avoidance are possible from the specifications of the main engine and propeller, but the inherent vibration frequency of the structure around the engine room is not easy to estimate due to the variation in the shape. Experience-oriented vibration design is also carried out, which results in many problems, such as process delay, over-injection of on-site personnel, and iterative performance of the design. For the flexible design of 8,600 TEU container vessels, this study addressed the resonance problem caused by the transverse vibration of the main engine when only the main engine was changed from 12 cylinders to 10 cylinders without modification of the hull structure layout. Efficient structural reinforcement design guidelines are presented for avoiding resonances with the main engine lateral vibration and the structure around the engine room. The guidelines are expected to be used as practical design guidelines at design sites.

• Tribology and Lubricants
• /
• v.24 no.3
• /
• pp.133-139
• /
• 2008

In recently designed diesel engines, the running conditions for piston pin bearings have become very severe due to combustion pressure and temperature increase. In this paper, it will be investigated the tendency of piston pin rotating motion by calculating the friction coefficient at piston pin bearings, the oil film thickness and the frictional torques induced by hydrodynamic shear stress. Finally, the pressure distributions on the oil film of piston pin bearings will be found by two-dimensional lubrication analysis in order to help the optimum design of the bearings of piston pin. Specially, it is investigated the effects on the film pressure distribution due to the change in maximum combustion pressure.

• 한국전산유체공학회:학술대회논문집
• /
• 2010.05a
• /
• pp.1-1
• /
• 2010

With the power of supercomputers increasing exponentially, there is an insatiable need for more advanced multi-disciplinary aerospace CFD simulations. A particular current interest is the 3D viscous turbulent simulation of the highly nonlinear aspects of aero-icing. The applications of CFD in that field are literally light-years behind aerodynamics, with a significant number of users still mired in correlations, or 2D, inviscid, incompressible, and, yes, Panel Methods simulations! Thus, the disparity of tools between aerodynamics and icing departments within an organization leads to a disconnect that makes ice protection a downstream isolated process that is not an integral part of the aerodynamic behavior of an aerospace system (aircraft, rotorcraft, jet engine, UAV, etc.). While 3D RANS has been recently introduced, it is still considered computationally too demanding for industry when wide parametric studies for certification are required. In addition, not unlike the situation in aerodynamics say 20 years ago, naysayers are at every corner claiming that CFD is not reliable and is of limited use.

• Proceedings of the KWS Conference
• /
• 2005.11a
• /
• pp.168-170
• /
• 2005

Nickel base brazes containing boron and silicon as melting point depressants are used extensively in the joining and repair of hot-section components in next generation nuclear reactor and aero-engine. Therefore, the present study has investigated the preliminary applicability of nickel based alloying nano powders. Nano Ni-based alloying powders synthesized by Pulsed Wire Evaporation (PWE) method. It's powder morphology and phase transformation temperature were analyzed by scanning electron microscopy, transmission electron microscopy, and differential scanning calorimeter(DSC). The powder particle size was approximately 10${\sim}$100nm and exhibits a quite even equiaxed shape. The results of DSC measurement show that both the nano Inconel 625 nano powder and Inconel 718 nano powder presents similar liquidus temperatures approximately $1373^{\circ}C$ and $1380^{\circ}C$ respectively.