• Carbon letters
• /
• v.2 no.3_4
• /
• pp.176-181
• /
• 2001

A series of activated carbons were prepared from coconut shells and coal-tar pitch binder by physical activation with steam in this study. The effect of variable processes such as activation temperature, activation time and ratio of mixing was investigated for optimizing those preparation parameters. The activation processes were carried out continuously. The nitrogen adsorption isotherms at 77 K on pellet-shaped activated carbons show the same trend of Type I by IUPAC classification. The average pore sizes were about 19-21${\AA}$. The specific surface areas ($S_{BET}$) of pellet typed ACs increased with increasing the activation temperature and time. Specific surface area of AC treated for 90 min at temperature $900^{\circ}C$ was 1082 $m^2/g$. The methylene blue numbers continuously increased with increasing the activation temperature and time. On the other hand, iodine numbers highly increased till activation time of 60 min, but the rate of increase of iodine numbers decreased after that time. This indicates that new micropores were created and the existing micropores turned into mesopores and macropores because of increased reactivity of carbon surface and $H_2O$.

• Journal of Microbiology and Biotechnology
• /
• v.8 no.1
• /
• pp.53-60
• /
• 1998

This study examines the effect of pH, temperature, metal ion concentration and culture density on metal biosorption by the nuisance cyanobacterium Microcystis aeruginosa. Ni biosorption was higher at pH 9.2 than at neutral and acidic pH. In contrast the biosorption of Cu and Zn was maximum at pH 7.0. However, biosorption of Zn was difficult to measure at pH values 9.2 and 10.5, owing to the formation of insoluble complexes. All the test metals (Cu, Zn, and Ni) showed maximum biosorption rate at low culture densities of 40 mg dry wt $1^{-1}$. The biosorption of Cu, Zn, and Ni was maximum at $40^{\circ}C$. However, no worthwhile difference in Zn and Ni sorption was noticed at 4 and $29^{\circ}C$ as compared to $40^{\circ}C$. Of these three metals used Microcystis showed a greater binding capacity ($K_{f}$ value=0.84, Freundlich adsorbent capacity) and accelerated biosorption rate for Cu under various environmental conditions. Fitness of mathematical models on metal biosorption by Microcystis confirmed that the biological materials behave in the same way as physical materials. These results suggest that before using a biosorbent for metal recovery, the environmental requirements of the biosorbent must be ascertained.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2011.05a
• /
• pp.49.2-49.2
• /
• 2011

$PbMoO_4$ nanoparticles were successfully obtained in the presence of ethylene glycol (EG) with the assistance of a prolonged sonication process. The nanoparticles were characterized by X-ray powder diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), diffuse reflectance spectroscopy (DRS) and adsorption-desorption $N_2$ isotherms (BET). The catalyst prepared sonochemically showed higher photocatalytic activity than $PbMoO_4$ prepared by solid-state reaction in the degradation reactions of rhodamine B (rhB), indigo carmine (IC), orange G (OG), and methyl orange (MO) under UV-Vis light radiation. In order to elucidate aspects of the degradation mechanism of the organic dyes, some experimental variables were modified such as pH, $O_2$ level in solution, and radiation source. In general, the photocatalytic activity for the degradation of organic dyes followed the sequence IC>OG>rhB>MO.

• Macromolecular Research
• /
• v.15 no.6
• /
• pp.565-574
• /
• 2007

In this study, five representative, commercially available polymers, Ultem 1000 polyetherimide, Kapton polyimide, phenolic resin, polyacrylonitrile and cellulose acetate, were used to prepare pyrolyzed polymer membranes coated on a porous {\alpha}-alumina$ tube via inert pyrolysis for gas separation. Pyrolysis conditions (i.e., final temperature and thermal dwell time) of each polymer were determined using a thermogravimetric method coupled with real-time mass spectroscopy. The surface area and pore size distribution of the pyrolyzed materials derived from the polymers were estimated from the nitrogen adsorption/desorption isotherms. Pyrolyzed membranes from polymer precursors exhibited type I sorption behavior except cellulose acetate (type IV). The gas permeation of the carbon/{\alpha}-alumina$ tubular membranes was characterized using four gases: helium, carbon dioxide, oxygen and nitrogen. The polyetherimide, polyimide, and phenolic resin pyrolyzed polymer membranes showed typical molecular sieving gas permeation behavior, while membranes from polyacrylonitrile and cellulose acetate exhibited intermediate behavior between Knudsen diffusion and molecular sieving. Pyrolyzed membranes with molecular sieving behavior (e.g., polyetherimide, polyimide, and phenolic resin) had a $CO_2/N_2$ selectivity of greater than 15; however, the membranes from polyacrylonitrile and cellulose acetate with intermediate gas transport behavior had a selectivity slightly greater than unity due to their large pore size.

• Bulletin of the Korean Chemical Society
• /
• v.34 no.12
• /
• pp.3805-3810
• /
• 2013

The surface modification of silica particles (SPs) was systemically conducted by the treatment of 0.1-10 wt % phenylsilanetriol (PST) on the basis of SPs used through two step processes: 1) the PST coating of SPs via evaporation under reduced pressure and 2) their thermal condensation leading to Si-O-Si bond formation via heating at $130^{\circ}C$. The evaluation of the modified SPs was conducted by the simple floating test on water and the measurement of the contact angle (CA) of water droplet on the 2-dimensional layer of modified SPs on slide glass. When PST was used about 2 wt % or above on the basis of SPs (about average size: 50 nm) used, the modified SPs were fully floated on the water and all dispersed into upper organic solvent layer after a shaking with the mixture of the water and benzene, indicating that the modified SPs have hydrophobic properties. The modified SPs were characterized by $^{29}Si$ MAS NMR and physicochemical properties including SEM, TEM, BET, adsorption/desorption isotherms, etc. were measured and compared each other in details. This research demonstrates that the organosilanetriol is a good modifier applicable for the surface modification of inorganic oxide particles using a low amount of modifier on the basis of oxide particles used.

• Biotechnology and Bioprocess Engineering:BBE
• /
• v.9 no.5
• /
• pp.331-338
• /
• 2004

The Separation of two amino acids, phenylalanine and tryptophan, was carried out using laboratory simulated moving bed (SMB) chromatography. The SMB process consisted of four zones, with each zone having 2 columns. The triangle theory was used to obtain the operating conditions for the SMB. The mass transfer coefficients of the two amino acids were obtained from the best-fit values by comparing simulated and experimental pulse data. The competitive adsorption isotherms of the two amino acids were obtained by single and binary frontal analyses, taking into consideration the competition between the two components. A competitive Langmuir isotherm, obtained from single-component frontal chromatography, was used in the first run, and the isotherm from binary frontal chromatography in the second, with the flow rate of zone 1 modified to improve the purity. Compared to the first and second runs, the competitive Langmuir isotherm from the binary frontal chromatography Showed good agreement with the experimental results. Also, adjusting the flow rate in zone 1 increased the purity of the products. The purities of the phenylalanine in the raffinate and the tryptophan in the extract were 99.84 and $99.99\%$, respectively.

• Journal of the Korean Chemical Society
• /
• v.26 no.4
• /
• pp.211-217
• /
• 1982

Assuming krypton molecules adsorbed on the graphite surface as a two-dimensional (2D) gas, 4th virial coefficient of the virial equation is calculated by the use of cluster integrals. The Henry's law constant, and 2nd and 3rd virial coefficients are also calculated. Adsorption isotherms calculated from this virial equation agree very satisfactorily with experimental results. The interaction energy of Kr-graphite surface is calculated assuming the pairwise additivity of Lennard-Jones(12,6) potential, and parametars therein are taken as; ${\varepsilon}_{gs}$/k = 71.1 K, ${\varepsilon}_{gg}$/k = 170 K, ${\sigma}_{gs}$ = 354 pm, and ${\sigma}_{gg}$ = 368 pm.

• Bulletin of the Korean Chemical Society
• /
• v.25 no.5
• /
• pp.726-736
• /
• 2004

In this paper, kinetics of reaction between Bromophenol blue (BPB) and $OH^-$, called fading, has been studied through a spectrophotometric method in the presence of nonionic Triton X-100 (TX-100), anionic sodium dodecyl sulfate (SDS) and cationic dodecyl trimethylammonium bromide (DTAB) surfactants. The influence of changes in the surfactant concentration on the observed rate constant was investigated. The results are treated quantitatively by pseudophase ion-exchange (PPIE) model and a new simple model called "classical model". The binding constants of BPB molecules to the micelles and free molecules of surfactants, their stoichiometric ratios and thermodynamic parameters of binding have been evaluated. It was found that SDS has nearly no effect on the fading rate up to 10 mM, whereas TX-100 and DTAB interact with BPB which reduce the reaction rate. By the use of fading reaction of BPB, the binding constants of SDS molecules to TX-100 micelles and their Langmuir and Freundlich adsorption isotherms were obtained and when mixtures of DTAB and TX-100 were used, no interaction was observed between these two surfactants.

• Carbon letters
• /
• v.14 no.3
• /
• pp.180-185
• /
• 2013

In this study, activated carbons nanofibers (ACNFs) were prepared from polyacrylonitrile-based nanofibers by physical ($H_2O$ and $CO_2$) and chemical (KOH) activation. The surface and structural characteristics of the porous carbon were observed by scanning electron microscopy and X-ray diffraction, respectively. Pore characteristics were investigated by $N_2$/77K adsorption isotherms. The specific surface area of the physically ACNFs was increased up to $2400m^2/g$ and the ACNFs were found to be mainly composed of micropore structures. Chemical activation using KOH produced ACNFs with high specific surface area (up to $2500m^2/g$), and the micropores were mainly found in the ACNFs. The physically and chemically ACNFs showed both mainly type I from the International Union of Pure and Applied Chemistry classification.

• Journal of the Korean Applied Science and Technology
• /
• v.31 no.2
• /
• pp.313-319
• /
• 2014

This study was performed to obtain high conversion efficiency of $NH_3$ and minimize generation of nitrogen oxides using metal-supported catalyst with Ag : Cu ratio. Through structural analysis of the prepared catalyst with Ag : Cu ratio ((10-x)Ag-xCu ($0{\leq}x{\leq}6$)), it was confirmed that the specific surface area was decrease with increasing metal content. A prepared catalysts showed Type II adsorption isotherms regardless of the ratio Ag : Cu of metal content, and crystalline phase of $Ag_2O$, CuO and $CuAl_2O$ was observed by XRD analysis. In the low temperature($150{\sim}200^{\circ}C$), a conversion efficiency of AC_10 recorded the highest(98%), whereas AC_5 (Ag : Cu = 5 : 5) also showed good conversion efficiency(93.8%). However, in the high temperature range, the amounts of by-products(NO, $NO_2$) formed with AC_5 was lower than that of AC_10. From these results, It is concluded that AC_5 is more environmentally and economically suitable.