• Journal of electromagnetic engineering and science
• /
• v.15 no.1
• /
• pp.53-58
• /
• 2015

For the testing of nonlinear power amplifiers, this paper suggests an approach to design optimized multisine signals that could be substituted for the original modulated signal. In the design of multisines, complex coefficients should be determined to mimic the target signal as much as possible, but very few methods have been adopted as general solutions to the coefficients. Furthermore, no solid method for the phase of coefficients has been proven to show the best resemblance to the original. Therefore, in order to determine the phase of multisine coefficients, a time-domain nonlinear optimization method is suggested. A frequency-domain-method based on the spectral response of the target signal is also suggested for the magnitude of the coefficients. For the verification, multisine signals are designed to emulate the LTE downlink signal of 10 MHz bandwidth and are used to test a nonlinear amplifier at 1.9 GHz. The suggested phase-optimized multisine had a lower normalized error by 0.163 dB when N = 100, and the measurement results showed that the suggested multisine achieved more accurate adjacent-channel leakage ratio (ACLR) estimation by as much as 12 dB compared to that of the conventional iterative method.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.07a
• /
• pp.357-358
• /
• 2005

Compact power amplifier modules (PAM) for WCDMA/KPCS and GSM/WCDMA dual-band applications based on multilayer low temperature co-fired ceramic (LTCC) substrates are presented in this paper. The proposed modules are composed of an InGaP/GaAs HBT PAs on top of the LTCC substrates and passive components such as RF chokes and capacitors which are embedded in the substrates. The overall size of the modules is less than 6mm $\times$ 6mm $\times$ 0.8mm. The measured result shows that the PAM delivers a power of 28 dBm with a power added efficiency (PAE) of more than 30 % at KPCS band. The adjacent-channel power ratio (ACPR) at 1.25-MHz and 2.25-MHz offset is -44dBc/30kHz and -60dBc/30kHz, respectively, at 28-dBm output power. Also, the PAM for WCDMA band exhibits an output power of 27 dBm and 32-dB gain at 1.95 GHz with a 3.4-V supply. The adjacent-channel leakage ratio (ACLR) at 5-MHz and 10-MHz offset is -37.5dBc/3.84MHz and -48dBc/3.84MHz, respectively. The measured result of the GSM PAM shows an output power of 33.4 dBm and a power gain of 30.4 dB at 900MHz with a 3.5V supply. The corresponding power added efficiency (PAE) is more than 52.6 %.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.9 no.2
• /
• pp.51-59
• /
• 2010

In this paper, we propose an inverted type asymmetric Doherty amplifier with optimized efficiency characteristic in wanted output power back-off (OPBO) range according to peak to average power ratio of input signal In order to obtain optimized efficiency of the asymmetric Doherty amplifier in wanted OPBO, peak power ratio between main amplifier and peaking amplifier was determined and then impedance of 90 degrees impedance transformer was obtained by peak power ratio. The offset line length and peak dividing ratio of the asymmetric Doherty amplifier were also calculated. From the measurement results, the proposed amplifier has achieved 40 % drain efficiency and -35 dBc adjacent channel leakage ratio at the average output power of 48.7 dBm for CDMA 2000 1x 3-FA test signal.

• Korean Journal of Optics and Photonics
• /
• v.8 no.4
• /
• pp.340-344
• /
• 1997

We proposed and demonstrated a tunable wavelength optical add/drop multiplexer(OADM) employing piezoactuated fiber grating pairs and polarization beam splitters. We used piezostack act as a fiber stretcher, using the fact that the resonant wavelength of the grating can be controlled by the axial strain along the fiber grating. The polarization controlled configuration showed high stability because the reflected signals from the two identical gratings are dropped or added not by interference but by polarizations of the beams. We could add and drop not noly 1549.3nm signal channel(original gratings), but also 1550.1nm(tuned gratings) with PZT actuators and in both cases, we found that the rejection of adjacent channels was more than -26dB, and signal leakage at the gratings was less than -34dB.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.17 no.6 s.109
• /
• pp.538-545
• /
• 2006

In this paper, an asymmetric high power extended Doherty amplifier for WCDMA base-station applications is presented. The amplifier has an extended peak efficiency over 9 dB of output power and a linear dynamic range characteristic. To realize the peak efficiency extension and linear dynamic range characteristic, a two times larger peaking device compared to the main device, and an unequal power divider are used. From the experimental results of 1FA WCDMA signal, this amplifier has an efficiency of 31 % and an ACLR of -35 dBc is achieved at 9 dB back-off from P1 dB.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.26 no.3
• /
• pp.292-299
• /
• 2015

An envelope elimination and restoration transmitter that uses a tri-level envelope encoding scheme is presented for improving the efficiency and linearity of the system. The proposed structure amplifies the same magnitude signal regardless of the input peak-to-average power ratio and reduces the quantization noise by spreading out the noise to the out-of-band frequency, resulting in the enhancement of power efficiency. An improved linearity is also obtained by providing a new timing mismatch calibration technique between the envelope and phase signal. Implementation in a 130 nm CMOS process, transmitter measurements on a 20-MHz long-term evolution input signal show an error vector magnitude of 3.7 % and an adjacent channel leakage ratio of 37.5 dBc at 2.13 GHz carrier frequency.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.18 no.11
• /
• pp.1262-1270
• /
• 2007

In this paper, we propose a new distortion cancellation mechanism for a balanced power amplifier structure using the carrier cancellation loop of a feedforward and post-distortion technique. The proposed cross post-distortion balanced linear amplifier can reduce nonlinear components as much as the conventional feedforward amplifier through the output dynamic range and broad bandwidth. Also the proposed system provides higher efficiency than the feedforward. The capacities of power amplifier and error power amplifier in the proposed system are analyzed and compared with those of feedforward amplifier. Also the operation mechanisms of the three kind loops are explained. The proposed cross post-distortion balanced linear power amplifier is implemented at the IMT-2000($f_0=2.14\;GHz$) band. With the commercial high power amplifiers of total power of 240 W peak envelope power fer base-station application, the adjacent channel leakage ratio measurement with wideband code division multiple access 4FA signal shows 18.6 dB improvement at an average output power of 40 dBm. The efficiency of fabricated amplifier Improves about 2 % than the conventional feedforward amplifier.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.25 no.9
• /
• pp.895-902
• /
• 2014

This paper presents a 2-stage CMOS power amplifier for the 1.75 GHz band using a $0.18-{\mu}m$ CMOS process. Using ADS simulation, a power gain of 28 dB and an efficiency of 45 % at an 1dB compression point of 27 dBm were achieved. The implemented CMOS power amplifier delivered an output power of up to 24.8 dBm with a power-added efficiency of 41.3 % and a power gain of 22.9 dB. For a 16-QAM uplink LTE signal, the PA exhibited a power gain of 22.6 dB and an average output power of 23.1 dBm with a PAE of 35.1 % while meeting an ACLR(Adjacent Channel Leakage Ratio) level of -30 dBc.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.49 no.1
• /
• pp.68-72
• /
• 2012

In this paper, highly linear power amplifier using bandpass filter based on metamaterial and Composite Right- / Left-Handed (CRLH) structure is proposed. The proposed bandpass filter consist of the series capacitor, series microstrip line and the parallel inductor, parallel microstrip line. The insertion loss is minimized at operation frequency and the $2^{nd}$ harmonic is suppressed by the bandpass filter using the CRLH structure. And we improved the Adjacent Channel Leakage Ratio (ACLR) using the characteristic of the proposed bandpass filter. At 2.14 GHz, we have obtained the output power of 38.83 dBm, the $2^{nd}$ harmonic of .61.33 dBc, the $3^{rd}$ IMD of .54.67 dBc, and ACLR of .51.33 dBc at 5 MHz offset, -56.50 dBc at 10 MHz offset, respectively.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.27 no.1
• /
• pp.50-59
• /
• 2016

This work shows that the design and test results of a power amplifier(PA) with broadband and high linearity for 4G applications in $0.11{\mu}m$ CMOS process. A 1:2-transformer is designed for load impedance matching of PA and a inter-stage matching is implemented for a linearity. A designed PA achieves more than 27.3 dBm of linear output power and 26.1 % of power-added efficiency(PAE) under an adjacent channel leakage ratio(ACLR) of -30 dBc for a LTE 16-QAM 10 MHz signal with a carrier frequency range of 1.8 to 2.3 GHz.