• 대한치과보철학회지
• /
• 제40권4호
• /
• pp.365-373
• /
• 2002

The purpose of this study was to investigate the effects of desensitizer on shear bond strength of adhesive resin cements for all ceramic crown. For this study, Gluma $desensitizer^{(R)}$(Heraeus Kulzer, Germany) and MS $Coat^{(R)}$(Sun medical, Japan) were used as desensitizer, and Bistite $II^{(R)}$ resin cement(Tokuyama, Japan) and Variolink $II^{(R)}$ resin cement (Ivoclar, Liechtenstein) were used. IPS Empress ceramics were bonded to dentin surfaces after application of desensitizer and shear bond strength of specimens were measured using UTM(Zwick 1456 41. Zwick, Germany) at a crosshead speed of 1mm/min. The obtained results were as follows : 1. The shear bond strength of both resin cements were not affected by Gluma $desensitizer^{(R)}$ containing HEMA 2. The shear bond strength of Bistite $II^{(R)}$ resin cement was significantly decreased by MS $Coat^{(R)}$. 3. The failure mode in MS $Coat^{(R)}-Bistite \;II^{(R)}$ group was mainly adhesive type between dentin and resin cement. but that of Gluma $desensitizer^{(R)}$-Variolink $II^{(R)}$ group was mainly mixed type, combined adhesive failures between dentin and resin cement or porcelain and resin cement.

• Journal of the Korean Wood Science and Technology
• /
• 제41권2호
• /
• pp.158-163
• /
• 2013

Cross laminated timber (CLT) has been an rising issue as a promising building material replacing steel-concrete in mid story rise construction. But, there was no specific standard for CLT because it had been developed in industrial section. Recently, new draft for requirements of CLT was proposed by EN which suggested to evaluate the performance of adhesive in CLT by the same method as glulam. But, it has been reported that shear performance of cross laminated timber is governed by rolling shear. Therefore, block shear tests were carried out to compare parallel to grain laminating and cross laminating using commercial one component PUR (Poly urethane resin). The result showed that the current glulam standard for evaluating bonding performance is not appropriate for CLT. Beacause shear strength of cross laminating decreased to 1/3 of parallel to grain laminating and this strength was representing shear performance of wood itself not the bond. However, cross laminating showed no significant effect on wood failure. Thus, wood failure can be used as a requirement of CLT bonding. Based on the results, cross laminating effect should be included when evaluating adhesive performance of CLT correctly and should be considered as an important factor.

• 대한치과기공학회지
• /
• 제33권1호
• /
• pp.1-6
• /
• 2011

Purpose: To examine the shear bond strengths of zirconia and veneering ceramic according to their surface processing. Methods: The test samples were divided into three groups: one without zirconia surface processing, one sandblasted, and one sandblasted then 3% etched. Then veneering ceramic was fired on all test samples, and their shear bond strengths were measured. Results: The test samples of the control group (Z1) showed the lowest shear bond strengths of $21.82{\pm}1.02$ MPa. The shear bond strengths of Z2 and Z3 ($28.25{\pm}0.72$ and $26.23{\pm}0.82$ MPa, respectively) were relatively higher than those of the control group. The fracture surface of the control group showed adhesive fractures while the test groups had relatively large numbers of cohesive fractures. Conclusion: The shear bond strength was high in the test groups with surface processing while the fracture surfaces showed compound fractures of adhesive and cohesive fractures.

• The Journal of Advanced Prosthodontics
• /
• 제9권2호
• /
• pp.85-92
• /
• 2017

PURPOSE. The aim of this study was to evaluate the effect of tooth surface pre-treatment steps on shear bond strength, which is essential for understanding the adhesive cementation process. MATERIALS AND METHODS. Shear bond strengths of different cements with various tooth surface treatments (none, etching, priming, or etching and priming) on enamel and dentin of human teeth were measured using the Swiss shear test design. Three adhesives (Permaflo DC, Panavia F 2.0, and Panavia V5) and one self-adhesive cement (Panavia SA plus) were included in this study. The interface of the cement and the tooth surface with the different pre-treatments was analyzed using SEM. pH values of the cements and primers were measured. RESULTS. The highest bond strength values for all cements were achieved with etching and primer on enamel ($25.6{\pm}5.3-32.3{\pm}10.4MPa$). On dentin, etching and priming produced the highest bond strength values for all cements ($8.6{\pm}2.9-11.7{\pm}3.5MPa$) except for Panavia V5, which achieved significantly higher bond strengths when pre-treated with primer only ($15.3{\pm}4.1MPa$). Shear bond strength values were correlated with the micro-retentive surface topography of enamel and the tag length on dentin except for Panavia V5, which revealed the highest bond strength with primer application only without etching, resulting in short but sturdy tags. CONCLUSION. The highest bond strength can be achieved for Panavia F 2.0, Permaflo DC, and Panavia SA plus when the tooth substrate is previously etched and the respective primer is applied. The new cement Panavia V5 displayed low technique-sensitivity and attained significantly higher adhesion of all tested cements to dentin when only primer was applied.

• 대한치과교정학회지
• /
• 제32권4호
• /
• pp.293-300
• /
• 2002

본 연구의 목적은 산부식된 법랑질에 수분이나 타액이 오염되어도 적절한 접착력을 얻을 수 있다고 소개된 교정용 친수성 프라이머를 이용한 교정용 브라켓 접착시 타액 오염 정도에 따른 전단결합강도와 접착 파절 양상을 기존의 소수성 프라이머와 비교함으로써 임상적 유용성을 평가하는 것이다. 사람의 소구치를 강철 원통에 교정용 레진으로 포매하여 만든 시편에 기존의 소수성인 Transbond XT primer와 친수성인 Transbond MIP primer각각에 대하여 광중합형 접착 레진으로 브라켓을 접착시, 인공 타액을 이용한 오염정도에 따른 전단결합강도를 만능시험기로 측정하고, 접착 파절 양상을 stereomicroscope로 관찰하여 다음과 같은 결과를 얻었다. 1. 건조 상태에서 Transbond XT primer와 Transbond MIP primer의 전단결합강도는 유의한 차이가 없었다. 2. 타액 오염시 그 정도에 상관없이 Transbond MIP primer는 Transbond XT primer에 비해 유의하게 높은 전단결합 강도를 나타냈다(p<0.001). 3. Transbond MIP primer는 한 겹의 타액 오염시 건조 상태와 전단결합강도의 유의한 차이가 없었으나, 두 겹의 타액 오염시에는 유의하게 낮은 결합강도를 나타냈다(p<0.01). 4. 접착 파절 형태는 타액 오염의 정도에 따라 평균 접착제 잔류 지수가 낮아지는 경향을 나타냈다. Transbond MIP primer는 타액 오염시에도 반 이상이 브라켓-레진 계면에서의 파절을 보였으나, Transbond XT primer는 타액 오염시 대부분의 경우 레진-법랑질 계면에서의 파절을 나타냈다. 이상의 실험 결과, 교정용 친수성인 Transbond MIP primer는 수분 조절이 어려운 임상 상황에서 적절한 결합강도를 얻을 수 있는 좋은 방법으로 생각된다.

• Restorative Dentistry and Endodontics
• /
• 제23권1호
• /
• pp.247-256
• /
• 1998

To evalutate the change in shear bond strength according to dentin surface treatment, 4 materials were divided into control group(A) and experimental group(B). Group A was treated according to the instruction of manufacture. Group B was treated with 32% phosphoric acid. After dentin surface treatment, each material was bonded and stored in 100% humidity during 7 days, and then, the shear bond strength was evaluated. The results were as follows: 1. In the case of treatment according to the instruction of manufacture, the shear bond strength according to material showed Z-100 to be highest with 12.42 MPa, Compoglass had the lowest shear bond strength with 4.23 MPa and there was significant difference between Compoglass and Z-100, Dyract (p<0.01). 2. The group treated with 32% phosphoric acid showed lower shear bond strength than that of the group treated according to the instruction of manufacture but there was no statistical significance. 3. As a result of observation under SEM, the fracture pattern was a mixture of cohesive and adhesive failure in group 1, and there was more adhesive failure in group 2, and in group 3 and 4 there was cohesive failure of material or tooth structure. From the results above Dyract showed shear bond strength levels between resin and resin -modified glass ionomer but Compoglass showed much lower shear bond strength than that of resin-modified glass ionomer thus indicating that even though they are the same type of material they show evident differences in physical properties. And it is thought that the treatment of dentin surface with phosphoric acid did not increase the shear bond strength, unlike enamel.

• 구강회복응용과학지
• /
• 제18권4호
• /
• pp.289-299
• /
• 2002

The bond strength is one of the most important factor in establishing long-term success of esthetic restorative dentistry. So, various restorative materials have been introduced to improve the esthetic and physical properties. Ormocer (organically modified ceramic) was developed as a result of such efforts. This study was performed to compare the shear bond strength of ormocer based adhesive with that of existing dentin adhesive. In this study $Admira^{(R)}$ and $Admira^{(R)}$ bond of the ormocer system are grouped together for ADM, Single $Bond^{(R)}$ which is an one-bottle adhesive and Z-250TM which is hybrid composite resin of BIS-GMA system for SIN, and $Definite^{(R)}$ of ormocer and Etch & $Prime^{(R)}$ 3.0 which is a self etching priming/ bonding agent for ETC. The results of this study were as follows. : (1) In the comparison of shear bond strength according to different adhesive system, shear bond strength was increased in the order of ETC group, SIN group, ADM group. There was no significant difference between ADM group and SIN group. However, there was a significant level of difference between ADM and ETC groups as well as SIN and ETC groups( p<0.05). (2) Examination by a scanning electron microscope showed a well established hybrid layer and resin tag in both ADM group and SIN group, while ETC group showed a minimal formation of the hybrid layer when compared with ADM and SIN groups. From the above results, it may be reasonable to start the clinical application of ormocer system, and it is recommended that ormocer system should be used along with an ormocer based adhesive because ormocer system showed the lower shear bond strength when it used with other existing self etching priming/bonding agent. The self etching priming/bonding agent showed relatively low shear bond strength, and it is considered that the further study should be needed.

• 대한치과보존학회:학술대회논문집
• /
• 대한치과보존학회 2001년도 추계학술대회(제116회) 및 13회 Workshop 제3회 한ㆍ일 치과보존학회 공동학술대회 초록집
• /
• pp.560.1-560
• /
• 2001

To evaluate the micro-shear bond strength of current adhesive systems to cervical and mid-coronal enamel. Materials and Two commercially available resin adhesives were investigated; a self-etching primer system(Clearfil SE Bond, Kyraray) and a one-bottle adhesive system(Single Bond, 3M) intended for use with the total-etch wet-bonding technique were employed. Two regions of enamel, cervical and mid-coronal regions, were chosen from the buccal surface of extracted molars and were then bonded with each adhesive system and submitted to the micro-shear bond test.(중략)

• Journal of the Korean Wood Science and Technology
• /
• 제45권3호
• /
• pp.243-249
• /
• 2017

본 연구는 국산 잣나무를 활용한 구조용집성판(cross laminated timber; CLT) 제조 기술 확립을 위한 일환으로 구조 용집성판 제작 시 접착조건을 구명하기 위해 수행되었다. 페놀레조시놀공축합수지(phenol resorcinol formaldehyde; PRF) 접착제를 적용하여 도포량과 압체압력 조건을 달리하여 목리가 수직 또는 수평한 경우의 전단시험에 의해 접착 강도를 확인하였다. 실험결과, 적정 접착조건은 도포량 $250g/m^2$, 압체압력 0.8 MPa로 결정하였다. 목리방향별 접착력에 있어서는 목리를 수직방향으로 접착할 때 평행하게 접착된 경우보다 낮은 값을 보였다. 이는 목리를 수직방향으로 접착한 시험편의 경우 다수가 롤링전단에 의해 파괴된 것과 연관이 있는 것으로 판단되었다. 한편 목리가 수평한 방향으로 접착된 경우, 국내외 기준에서 제시하고 있는 전단접착 강도 기준을 만족하였으며 목리가 수직한 방향으로 접착한 경우 국외 기준에 제시된 기준을 만족하였다. 본 연구에서 도출된 최적 접착조건을 적용하여 국산 잣나무 구조용집성판 제조 시 국내외 기준에 준하는 접착성능 확보가 가능할 것이며, 또한 도출 데이터는 구조용집성판 및 구조용집성재 제조 시 참고 데이터로 활용될 수 있을 것이다.

• Journal of Korean Dental Science
• /
• 제1권1호
• /
• pp.28-34
• /
• 2008

Objectives. The objectives of this study were: 1) to compare the effect of varying timing of light curing on shear bond strength, and; 2) to compare the shear bond strength of three self-adhesive cements. Materials and methods. A total of 72 extracted non-carious teeth were divided into 24 for Unicem tests, 24 for Maxcem tests, and 24 for Biscem tests; they were assigned 3 * 2 subgroups of 12 teeth each. The specimens were prepared as follows: 1) The calculus and periodontal ligament were removed from the teeth; 2) The teeth were stored in normal saline; 3) The occlusal enamel of each tooth was removed using high-speed coarse diamond burs under water cooling, and; 4) Finally, the teeth were flattened by 600-grit silicone carbide paper disks. Resin blocks were adhered using either Unicem, Maxcem, or Biscem. Light curing timing was divided into two groups: U10, M10, and B10 were exposed to light after 10 seconds, and; U150, M150, and B150 on the other side were exposed to light after 150 seconds. Shear bond strength was measured by a Universal testing machine with cross head speed of 1mm/min. T-test and One way ANOVA were used for the statistical analysis of data. Results. The shear bond strength of U150 was not significantly higher than that of U10 (U150: 20.55.7Mpa, U10: 18.73.80Mpa). On the other hand, the shear bond strength of M150 was significantly higher than that of M10. The shear bond strength of B150 was also significantly higher than that of B10 (M150:14.45.7Mpa, M10: 9.94.2Mpa, B150: 24.38.3Mpa, B10: 17.27.3Mpa). When the light curing timing was 10sec after bonding, the shear bond strength of Unicem was highest; the shear bond strength of Biscem was highest when the light curing timing was 150sec after bonding (U10: 18.73.80Mpa, B150: 24.38.3Mpa). Significance. Since Unicem is less sensitive based on light curing timing, dentists seem to use it without considering the light curing timing. Maxcem showed the lowest bonding strength (especially M10). Thus, when using Maxcem, dentists need to delay the light curing after adhesion.