• 한국정밀공학회지
• /
• 제22권2호
• /
• pp.139-147
• /
• 2005

The lubricant impregnated MC nylon has good frictional properties, but its mechanical strength is inferior to steel for the mechanical elements. For the tribological application Nylon as gears, sliding bearings, cam and etc, the steel shafts are fitted in pre-heated nylon cylinder by a process of interference expansion fit and bonded by induction heating method. The joint shear strength of the two materials was measured by a universal test machine. From the study, the adhesive shear strength between these two materials was affected by the factors of the interference between nylon and steel, the size of nylon cylinder, knurl of steel shaft and inducting heating conditions. The most effective jointing conditions were analyzed and decided for the practical application in the industry.

• Journal of the Korean Wood Science and Technology
• /
• 제24권2호
• /
• pp.15-19
• /
• 1996

To utilize the waste materials and develope wood adhesive from isolated bloods of slaughtered cow and pig and also to prevent water pollution, simple and rapid method of isolation and purification of plasma proteins from pig bloods with trichloroacetic acid(TCA) treatment was developed. Adding of TCA-precipitated blood powder to the phenol formaldehyde resin(PF) improved dry and wet strength of plywood and resulted in fast hot pressing times.

• 미생물학회지
• /
• 제12권3호
• /
• pp.147-148
• /
• 1974

A small amount of Duco cement or Elmer's clear cement was dropped on a slide glass and immediately spread with a glass rod or woden stick a thin film on the surface. After approximately 1 minute a small amount of rubber cement was spread on the top of the film of Duco cement using the same method as described earlier. It was important that the rubber cement be smeared before the Duco cement dried out. These two kinds of cements must not be mixed. It was better to make the film of the rubber cement slightly thicker than the film of Duco cement. This composite film may be used up to several months after preparation. The sample leaf was placted on the slide, prepared with adhesive and the leaf surface was passed on the film with the thumb. The pressing was done so the leaf surface was completely in contact with the film. Then the leaf was peeled from the slide.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2005년도 추계 학술논문 발표대회
• /
• pp.79-83
• /
• 2005

In the reinforced concrete structure, Even if speak that water leakage occurrence is no problem to material, there is a lot of reasons construction factor, material damage by behavior structure, properties of matter change by years and water leakage part by environment condition. so, waterproofing technological consideration should be gone ahead. In this research, we will study about stick performance, concrete surface adhesive, damage and blow. we will check all things and test it. The stick expansion type complex of flexible material passed on result of standard. It is conducive to concrete of durability by waterproofing layer performance demobilitation technology on the water leakage structure for solution of problem and repair

• 대한가정학회지
• /
• 제36권2호
• /
• pp.121-130
• /
• 1998

The purpose of this study was construction of bell-bottom blue jeans according to change of flare line and investigate the effects clothing pressure according to various movements of the legs. In this study, movements of leg were classified by M1, M2, M3, M4.(M1:erecting, M2: leapfrogging position, M3:sit-on-one' keens position, M4:Traditional nobel-sitting position) The results were as follows: As usings the leg surface shell by the adhesive paper taping method, basic slacks pattern and blue jeans patterns according to change of flare line was constructed. The order of clothing pressure of the different patterns is C(the flare line is on the calf of the leg)>B(the flare line is on the knee)>A(the flare line is on the thigh). Clothing pressure in the knee point was highest and when the flare line was on the calf of the leg, clothing pressure showed high.

• Earthquakes and Structures
• /
• 제6권3호
• /
• pp.237-250
• /
• 2014

This paper experimentally investigates the seismic performance of RC columns retrofitted with Super Reinforcement with Flexibility (SRF), which is a polyester fiber reinforced polymer. A total of three specimens with a scale factor of 1/2 were constructed and tested in order to assess the structural behavior of the retrofitted RC columns. One specimen was a non-seismically designed column without any retrofit, while others were retrofitted with either one or two layers of the polyester belt with urethane as the adhesive. Static cyclic testing with a constant axial load was conducted to assess the seismic performance of the retrofitted RC columns. It is concluded that the SRF retrofitting method increases the strength and ductility of the RC columns and can also impact on the failure mode of the columns.

• 한국응용과학기술학회지
• /
• 제28권2호
• /
• pp.240-246
• /
• 2011

UV-Curable hybrid coatings were synthesized to improve the surface properties of plastic film. Organic-inorganic coating solutions were prepared by the sol-gel method using urethane-acrylate oligomer, acrylate monomer, photo initiator and tetraethoxysilane (TEOS). Methacryloyloxypropyltrimethoxysilane(MPTMS) was used as a silane coupling agent to improve chemical interaction between inorganic phases and UV curable acrylate. In this study, the surface hardness and adhesive properties were improved with the use of inorganic component. The experimental results showed that UV-Curable hybrid films containing aliphatic urethane oligomer, hexanedioldiacrylate, trimethylolpropanetriacrylate, hydroxy dimethyl acetophenone exhibited good surface properties. Also, the optimum curing conditions were investigated.

• 한국표면공학회지
• /
• 제31권2호
• /
• pp.91-100
• /
• 1998

NiCrAlY/YSZ(8wt%$Y_2O_3-ZrO_2$) functionally graded thermal barrier coating (FGC) layers on a Co-base superalloy (HAYNESS 188) substrate were fabstrate were fabicated using Ar shielded single torch air plasma spraying method. Functional grading with the stepwise compositional change throughout layer thickness. Microstructural observation trvealed a successful fabrication of NiCrAlY/YSZ FGC. From the results of the curvature measurement, adhesive strength measurement and thermal shock test for the FGC, it was concluded that the optimum conditions of functionally graded coating layer thinkness and compositional pattern exit to enhance the properties of FGC, which is closely related to the internal residual stess distribution witin it.

• 마이크로전자및패키징학회지
• /
• 제8권3호
• /
• pp.25-30
• /
• 2001

반도체 칩과 얇은 접착제충의 계면에 존재하는 모서리 균열에 횡방향 인장변형률이 작용하는 경우에 대해 응력확대계수를 조사하고 있다. 이러한 균열들은 자유 경계면 부근에 존재하는 응력 특이성으로 인해 발생할 수 있다. 계면 응력상태를 해석하기 위해서 경계요소법이 사용되고 있다. 복합 응력확대계수의 크기는 균열의 크기에 의존하지만, 균열이 커지면 일정한 값에 수렴한다. 횡방향 인장변형률이 임계값에 도달하면, 계면 균열은 빠르게 전파되리라고 예상된다.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2009년도 9th International Meeting on Information Display
• /
• pp.152-155
• /
• 2009

A novel two-step surface treatment was developed and demonstrated for the carbon nanotube (CNT) cathode with highly efficient backlight unit application. An adhesive taping method was applied firstly and then followed by a post-heat treatment for the CNT cathode. During the postheat treatment process, some residues covering the CNTs were burned out. The post-heat treatment enhanced the emission current of the CNT cathode around 20% compared with that of no heat-treated sample.