• Journal of Korean Vacuum Science & Technology
• /
• v.6 no.4
• /
• pp.143-148
• /
• 2002

Method of plasma-immersion ion deposition of hydrogenated DLC films on relatively thick flat dielectric substrates from plasma of not-self-sustained low-pressure gas arc discharge is suggested. Coating properties have been investigated experimentally, average energy Per a deposited carbon atom depending on discharge current has been calculated. Optimum deposition parameters lot obtaining sufficiently hard and transparent high-adhesive a-C:H films on a 4-mm thick glass substrates have been determined. Possibility to use these coatings for photo-tools protection from abrasion wear at low operating loads is shown in general.

• Proceedings of the Korean Institute of Interior Design Conference
• /
• 2007.05a
• /
• pp.81-84
• /
• 2007

The purpose of this study was to grasp actual condition of remodeling elements by specialists' in-depth interviews. The interview has been conducted to interior designer who have a wide experience of apartment remodeling. In-depth interview is a kind of qualitative method in which attention to reply of responses with open-access between interviewer and respondents. According to the results, remodeling elements were generally the renovation of balcony into the livingroom or children room, removal a doorsill, installation of storage furniture, change of lighting fixtures in the all rooms and change equipments of bathroom. Finishing materials were usual used normal wallpaper and normal or low emitting adhesive on ceiling and wall, tempered-flooring on floor, and ceramic tiles on bottom and wall of bath and entrance.

• Architectural research
• /
• v.7 no.1
• /
• pp.19-26
• /
• 2005

Unlike other countries, Korea uses various kinds of wall-paper as finishing material. Conventional wall-paper consists of paper and vinyl, and petrochemical ink is used for the decoration of the surface. Adhesive is used to paste the wall with the wall-paper, which emit substantial amounts of VOCs and formaldehyde. In this study, VOCs characteristics emitted from specimens made of concrete, mortar, gypsum board and wall-paper were investigated using small chamber method. Moreover, concentration and emission factor of BTEX(Benzene, Toluene, Ethylbenzene, m,p,o-Xylene) and TVOC were investigated, and concentration and emission factor decay were estimated. As a result of the prediction, both time-dependent concentration decay and cumulative concentration can be converted into the logarithmic scale. Furthermore, prediction equations were developed from the experimental results under accurately controlled experimental conditions. Therefore, there may be difference if the estimated equations are directly applied to real buildings. Further research should be done on the generalization of the developed prediction equations.

• Journal of Biomedical Engineering Research
• /
• v.10 no.2
• /
• pp.195-202
• /
• 1989

Chinese Hamster Ovary( CHO) cells were cultured on the surface-modified polymers described in the previous study( "Polymer Surfaces for Cell Adhesion. 1. Surface Modification of Polymers and ESCA Analysis, " J. of KOSOMBE, Vol. 10, No. 1, 43-51, 1989). Among the physicochemical treatment methods. the chloric acid treatment was found to be the best method of rendering the polymer surfaces adhesive for CHO cells probably due to the high density of hydroxyl groups on the surface. Among the biological methods, the fibronectin treatment was best for CHO cell-compatibility probably due to specific active sites existed on the tell-binding domains of the fibronectin structure. When we compare the cell-compatibility of the chloric acid - and the fibronectin -treated PET surfaces, the number of cells attached on the surfaces were increased by 460.5 % and 559.0 % and, respectively, after 32 hr CHO cell culture, compared to that of untreated PET.eated PET.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2007.08b
• /
• pp.1125-1128
• /
• 2007

The laminating technique for developing flexible liquid crystal display was demonstrated by using a thin UV curable polymer film and a plastic substrate with patterned polymer wall structure. We adopted the rigid wall structure to provide a solid mechanical support for the stable molecular alignment of liquid crystals (LCs) in the device. The cover film was prepared to have an ability of aligning LC molecules by patterning a micro-groove structure using the soft-lithographic process. These two substrates can be assembled tightly by the laminating and one-step UV irradiation process because of the adhesive nature of the used UV curable polymers. Proposed method can be used to fabricate the flexible LC display with simplicity and also be applicable for a cost-effective roll-to-roll process.

• Journal of Adhesion and Interface
• /
• v.7 no.4
• /
• pp.18-23
• /
• 2006

The influence of the notch length on the stress distribution of mid-bondline and adherend was investigated using elasto-plastic finite element method. The results from the simulation showed that peak stress of mid-bondline decreased markedly as adherend with notch in the middle of lap zone, and the stress in the middle of joint with low stress originally increased evidently. All the peak stresses decreased firstly and increased again as the length of notch increased. The relative higher peak stress appeared at the point near the notch of adherend where might be failed previously during the loading procedure.

• Proceedings of the KWS Conference
• /
• 2002.10a
• /
• pp.1-14
• /
• 2002

There is a continuous development of the most common welding processes like MMA, MIG/MAG, PAW and SAW. At the same time there is a conversion from stick electrodes to solid and cored wires with an increased productivity as a result. In parallel with these changes new processes are introduced and implemented. The number of Friction Stir Welding installations is starting to grow fast Hybrid laser welding has probably made a technical break through. The Magnetic Pulse Welding process is taking off. The different mechanical joining methods; clinching and self-piercing riveting; must not be forgotten. Structural adhesive is another method to consider.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2006.05b
• /
• pp.653-656
• /
• 2006

It is necessary for the new material and construction concept to make up for weak point which related to high durability and finish ability to solve exposure limit of exist construction method. This paper is deal with performance test(tier load, anti abrasion, anti impact, permeability, bond test) compositive using for water reacting soft urethane and rigid urethane to improve the exist problem which are crack movement, adhesive on the wet surface, impact and abrasion by tier load. It is getting decreasing demage compare with other exist materials after test by transfer load, movement and impact.

• Biomedical Science Letters
• /
• v.19 no.1
• /
• pp.25-31
• /
• 2013

Electrospun nanofibers are being widely used as a substratum for mammalian cell culture owing to their structural similarity to collagen fibers found in extracellular matrices of mammalian cells and tissues. Especially, development of diverse synthetic polymers has expanded use of electrospun nanofibers for constructing cell culture substrata. Synthetic polymers have several benefits comparing to natural polymer for their structural consistency, low cost, and capability for blending with other polymers or small molecules to enhance their structural integrity or add biological functions. PMGI (polymethylglutarimide) is one of the synthetic polymers that produced a rigid nanofiber that enables incorporation of small molecules, peptides, and gold nanoparticles through co-electrospinning process, during which the materials are fixed without any chemical modifications in the PMGI nanofibers by maintaining their activities. Using the phenomenon of PMGI nanofiber, here I introduce a construction method of a nanofiber substratum having cell-affinity function towards a pluripotent stem cell by incorporating a small molecule in the PMGI nanofiber.

• Proceedings of the KSME Conference
• /
• 2003.04a
• /
• pp.1104-1110
• /
• 2003

There are many applications of nanostructures, have been suggested by lots of researchers. It is highly required to measure the properties of nano-sized materials for design and fabrication of the nanostructures. In this paper, several techniques for measuring the mechanical properties of nano-structures are presented laying emphasis on the activity of Nano Property Measurement Team in KIMM. Some advanced applications of nano-indenter are described for measuring elastic, visco-elastic, frictional and adhesive properties as well as the standard methods of it. Micro-tensile test technique with accurate in-plane strain measurement method is also presented and its role in the property measurement of nanostructures is discussed.