• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2005년도 봄학술 발표회 논문집(I)
• /
• pp.503-506
• /
• 2005

The purpose of this study was the Development of Retrofit Method for Beam Using Steel Plate Reinforced by Fiber Sheet.1. Additional reinforcements are not needed in the joining area of slab and beam web.2. Beam using carbon fiber reinforced plastic displays low effects in shearing effect.3. Beams reinforced steel plate by epoxy effect the capacities of strength. But the capacities of strength are rapidly reduced when adhesive surface be omitted. Thus details are needed in this case.4.Retrofit method for beam using steel plate reinforced by fiber sheet with epoxy rosin improves the capacities of strength and the initial stiffness, shows a large transformation since the maximum load likewise may be excellent to the shearing reinforcement.

• 한국자동차공학회논문집
• /
• 제12권1호
• /
• pp.130-137
• /
• 2004

The ultrasonic attenuation coefficients were measured by interfacial crack length in the adhesive components of double-cantilever beam(DCB). The energy release rate, G, was obtained by the experimental measurement of compliance. The numerical analysis by the boundary element method(BEM) and Ripling's equation was investigated. The experimental results represent that the relation between interfacial crack length for the ultrasonic attenuation coefficient and energy release rate is increased proportionally. A measurement method of the interfacial crack length by the ultrasonic attenuation coefficient was proposed and discussed.

• 대한약학회:학술대회논문집
• /
• 대한약학회 2003년도 Proceedings of the Convention of the Pharmaceutical Society of Korea Vol.2-2
• /
• pp.235.2-235
• /
• 2003

To develop the buccal delivery system of rhEGF for the treatment of buccal mucosal ulcer, polymer films and hydrogels were investigated. Methods: Hydrogels for thermosenstive sol/gel systems were prepared by the cold method (Schmolka, 1972). And mucoadhesive films were prepared by mixing sod. alginate/polycarbophil 974p. To find an optimum buccal mucosal adhesive gel or film, the gel strength of the poloxamer and sod. alginate/polycarbophil 974p hydrogels were determined by the Simple Rheology Method and their mucoadhesiveness were measured by the Instron (M 4400, Instron Co., U.S.A.) method. (omitted)

• 한국구조물진단유지관리공학회 논문집
• /
• 제18권4호
• /
• pp.50-58
• /
• 2014

신축공사의 비용에 대한 부담과 건설된 지 오래되어 노후화가 진행된 철근콘크리트 구조물의 증가로 유지관리의 필요성이 크게 증가하여 점차적으로 보수 보강 분야가 확대되고 있다. 이러한 필요성의 증가로 인해 새로운 보수 보강 기술이 국내 외에서 지속적으로 연구되고 있다. 국내에서는 철근콘크리트 구조물의 보수 보강공법으로 강판접착공법, 섬유보강 (Fiber reinforced plastic, 이하 FRP) 표면부착공법, 외부 프리스트레싱공법 등이 사용되고 있다. 이러한 방법 외 Steel mesh로 보강한 시멘트 모르타르 (Steel Mesh Cement Mortar; SMCM)을 이용한 보수방법을 고려하고자, Steel mesh 의 보강 면적, 그리고 보강 층 수 (number of layer)를 달리하여, 3점 휨 부재 실험을 수행하였다. $1400{\times}500{\times}200$ (mm)의 기본 철근 콘크리트 (RC)를 포함하여 총 5종류의 시편을 제작하였으며, 처짐량을 측정하기 위해, 시편 상부에 LVDT를 설치하였으며, 시편 중앙부에 철근 변형률 게이지와 콘크리트 변형률 게이지, 전단 철근에 철근 변형률 게이지를 부착하였다. 3점 휨 실험 결과, 모든 하중-변위 곡선에서 공통적으로 SMCM으로 보강한 시편이 기본 RC에 비해 최대하중이 더 높은 것을 확인할 수 있었다. SMCM을 두 층, 그리고 기본 RC 하부 전체에 보강을 할 경우, 기본 RC에 비해 최대 하중은 1.18배, 처짐은 최대 1.37배 더 높은 것을 확인할 수 있었다. 시편의 종류마다 조금씩 다른 양상을 보였는데, 이는 SMCM과 RC의 부착 정도의 차이로 인해 결과의 차이가 발생한 것으로 보인다. 특히, 지점부 안쪽으로 부분 보강하고, Steel Mesh를 한 겹으로 보강한 네 번째 경우 (SM-B1)에는, SMCM이 실험 도중 박락되는 현상이 발생하였다. SMCM을 보수 보강 재료로서 활용하기 위해선 RC와의 부착 성능 향상이 필요하다고 판단된다.

• 대한소아치과학회지
• /
• 제30권4호
• /
• pp.581-592
• /
• 2003

본연구는 유치와 영구치의 우식상아질을 제거하는 방법에 따른 상아질표면의 변화와 산부식양상, 혼성층의 양상, 그리고 이들이 상아질에 대한 복합레진의 전단결합강도에 미치는 영향을 평가할 목적으로 시행되었다. 92개의 유구치와 92개의 영구 구치를 준비하여 상아질 표면을 노출시키고 인공우식을 유발시켰다. 이중 32개의 유구치와 32개의 영구구치는 $Carisolv^{TM}$과 bur로 삭제후 상아질표면을 SEM관찰하였으며 나머지 치아에서는 레진-상아질간 전단결합강도를 측정하였다. 두가지 접착시스템(Single bond system, self-etching bonding system)과 한 종류의 레진(Z250, 3M)을 사용하였으며 다음과 같은 결과를 얻었다. 1. $Carisolv^{TM}$의 우식치질 제거효과는 영구치보다 유치에서 더 우수하였으며, bur로 제거한 경우보다 더 거친 상아질 표면이 관찰되었다. 2. 산부식처리한 경우 유치와 영구치 모두 우식제거방법과 관계없이 도말층이 제거된 양상을 보였다. 3. Single bond system을 이용한 경우 두터운 $2-4{\mu}m$의 혼성층과 $10-15{\mu}m$의 adhesive layer가 관찰된 반면, self-etching bonding system에서는 비교적 얇은($1-2{\mu}m$) 혼성층만이 형성되었다. 4. 전단결합강도는 유치와 영구치 모두 우식제거방법에 관계없이 Single bonding agent를 적용한 경우에 self-etching bonding agent를 적용한 군보다 유의하게 높게 나타났다(P<0.05). 5. $Carisolv^{TM}$와 self-etching bonding agent 처리군에서 bur와 self-etching system 처리군보다 다소 높은 전단결합강도를 보였으나 유의성은 없었다(P>0.05).

• 공학기술논문지
• /
• 제6권2호
• /
• pp.121-124
• /
• 2013

This paper proposed a new concept of estimating method for LED(light-emitting diode) delamination with high accuracy. Usually, The LED is composed several materials which are LED chips, gold wire, phosphor, epoxy resin, adhesive, reflector and lead frame. These different materials are usually delaminated in a trouble conditions which are huge temperature difference, hot and humid or mechanical shocked. When the components are delaminated, a luminance will be lost, moisture be absorbed easily and a thermal resistance be increased attendantly. As a conventional method to estimate a delamination of LEDs, a solution immersing method is usually used in a field of LED manufacturing companies or researching institutes. This method has an advantage of simplicity but it is only shown that the existence of delamination or not. In this paper, we have proposed an estimating method for LEDs delamination using the polishing and the electron microscope. New proposed method has shown the result of confirming delamination without destruction and enabled quantitative analysis for LED delamination.

• 한국건축시공학회지
• /
• 제5권3호
• /
• pp.125-129
• /
• 2005

The waterproofing in slab and wall of underground structure, have a couple of construction methods which are inside waterproofing methods for inner surface, and outside waterproofing methods for out wall and slab surface waterproofing. In resent years, however, it has been adapted the inside waterproofing construction method, as increasing of construction expenses cost and low workability and technology, nevertheless, outside waterproofing has set a most high value construction method. In inside waterproofing construction method, it is difficult to repair and assure durability and safety for concrete which has direct water-press. So, It is necessary for adopt the outside waterproofing method. For that reasons, this study based on the application for outside waterproofing method on the under ground structure, to more increase durability, to introduce mono adhesive sheet waterproofing materials. as considering chemical, physical properties.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2008년도 추계 학술논문 발표대회
• /
• pp.49-52
• /
• 2008

The present study was to develop a dry PFB method similar to the existing gypsum board construction method in order to apply the existing wet PFB method that uses fire-resistant adhesive. It was found that the existing wet method can produce concrete compressive strength of 80MPa and fire resistance of 3 hours with 30mm PF boards. The goal of development in this study was fire resistance of 3 hours through dry construction of 15mm fire-resistant boards. 1. Improved PF board was prepared by adding inorganic fiber to existing board and using aggregate with grain size of 3mm or less. Molding was done at temperature higher than that for existing PF board molding. While wet curing is used for existing PF boards, this study used dry curing in order to enhance heat insulation performance. 2. According to the results of fire resistance test, when the dry PF method was applied, the temperature of the main reinforcing bar was 116℃ in 15mm, 103.8℃ in 20mm, and 94℃ in 25mm, and these results satisfied the current standards for fire resistance control presented by the Ministry of Land, Transport and Maritime Affairs. When a 3-hour fire resistance test was performed and the external properties of the specimen were examined, the outermost gypsum board hardly remained and internal PF board maintained its form without thermal strain.

• 접착 및 계면
• /
• 제5권2호
• /
• pp.5-14
• /
• 2004

Since flexible adhesives are used more and more in structural applications, designers should have a better understanding of its behaviour under various conditions as ultimate load, fatigue load, long-term load and environmental conditions. This paper focuses on long-term load conditions and its effect on flexible adhesives. The creep properties of both PU (PolyUrethane) and SMP (Silyl Modified Polymers) adhesives used for identical applications are considered. To investigate the creep behaviour tests under various conditions were done. The results of those tests are presented and compared. To evaluate these results an empirical method is proposed and discussed. An example illustrates the potential of this method. It is also shown that with use of a probabilistic calibration technique this method results into a simple rule, which can be used to calculate the creep for practical applications. For the studied adhesives, the creep performance of the SMP adhesive is shown to be of the same level or slightly better than of the two PU adhesives. In addition to this empirical method, the principles of a more complex theoretical based method are introduced. The potential of this method is illustrated and future research activities are drawn.

• Journal of Welding and Joining
• /
• 제34권3호
• /
• pp.31-39
• /
• 2016

The joining technology of the metal and engineering plastic is rising lately as the important issue in concerning with the method of reducing the weight and air pollution of the transportation structure such as automotive and vehicles. The metal/ plastic joining technology has been developed in 2 types of adhesively bonding and direct joining without adhesives. Moreover, in the direct joining method, there are 2 kinds of mechanical joining and welding. This review paper presents the present world wide status and tendency of the development of metal/plastic joining technology. This article intends to offer the materials for development and raising of the domestic metal/plastic joining technology.