• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2005년도 춘계 학술기술논문발표대회 논문집
• /
• pp.173-178
• /
• 2005

The tile construction methods for existing have been used materials within limit which adhesion by wet method in masonry wall and concrete structure. These existing adhesive tech can caused many problems in construction of large and reform tile, after that it can be happened loose scale, peel off, falling off tile by heat and vibration or impact. In according to, this study is to test tile for bond stability, adhesive property by impact, vibration. low property by heat and then, we have the results as below; (1) The tile adhesive stability can be effected as adhesive area between bond agent and tile, adhesive area can more wide and press enough to ensure property. (2) Existing adhesive strength and standard relative tile construction is limited to adjust performance tile on the concrete and masonry wall. In summary, It is necessary to establish standard of performance and test method to ensure tile adhesive salability in dry wall.

• 한국재난정보학회 논문집
• /
• 제15권2호
• /
• pp.259-267
• /
• 2019

연구목적: 본 논문에서 접착제로 접착된 원통형 랩 접합부는 피착체가 탄성이고, 접착제가 선형 점탄성이라고 가정한다. 연구방법: 피착제의 응력 분포는 유한요소법을 사용하며, 4개의 아이소파라메터 점탄성 고체 접착제를 통해 피착제에 대한 해석결과를 검증한다. 연구결과: 접착층에서의 시간에 대한 응력분포와 피착제의 두께와 탄성율이 규격화에 미치는 응력의 영향을 검토한다. 결론: 본 연구는 접착제층의 점탄성을 고려한 랩접착된 원통체의 접착제층의 응력분포에 대해서 4요소 탄성체 모델을 사용하여 수치해석을 하였다.

• Journal of the Korean Wood Science and Technology
• /
• 제16권3호
• /
• pp.5-16
• /
• 1988

This experiment was executed to investigate the effect of activation of veneer surface by oxidizing agents, hydrogen peroxide and nitric acid, on bonding characteristics of Malas(Homalium foetidum Benth) plywood, in which the effects of these oxidizing agents amount, pretreatment time, and pressing time and temperatue on shear strength of the plywood were examined and discussed. In this research the activation of veneer surface by oxidants was effective in raising shear strength but the difference in shear strength was not observed between hydrogen peroxide and nitric acid treatment. Hydrogen peroxide treatment, however, seemed to be more profitable to industrial application because of its lower concentration and easier handling than nitric acid. The bonding method by lignin-phenol adhesive through surface activation revealed inferior shear strength to phenol- and urea-formaldehyde adhesive but superior water resistance to urea-formaldehyde adhesive and this bonding method, in addition, have the advantage of lower cost compared with phenol-formaldehyde adhesive, Therefore, this bonding method by lignin-phenol adhesive through surface activation seemed to economical in manufacturing of water-resistant wood panel materials in future.

• Composites Research
• /
• 제31권4호
• /
• pp.151-155
• /
• 2018

기계적 조인트와 접착 조인트는 구조물의 일반적인 접합 방법이다. 접착 조인트는 기계적 체결법에 비해 넓은 면적에 하중이 분포되고 우수한 피로 특성을 가진다. 이러한 특성에도 불구하고, 접착 조인트는 환경조건이나 작업자의 숙련도에 대한 접착 건전성이 크게 달라진다. 따라서 접착 조인트의 건전성을 평가 할 수 있는 기술이 필요하다. CNT를 접착제에 분산시켜 접착조인트의 전기적 특성을 측정하는 전기저항법은 결함을 검출하는 매우 유망한 기술이다. 본 논문에서는 초음파 분쇄기와 3-roll-mill을 이용하여 접착제에 CNT를 균일하게 분산시켰으며, 알루미늄-알루미늄 단일 접착 조인트를 제작하여 탄소나노튜브(CNT) 함량에 따른 정적 강도의 변화를 평가하고, 전기저항법을 이용하여 결함탐지능을 평가하였다.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2021년도 봄 학술논문 발표대회
• /
• pp.183-184
• /
• 2021

Defects such as falling and cracking of tiles installed in the bathrooms of apartment houses are frequently occurring. Therefore, in order to solve this problem, the A/S cost of construction companies and consumer complaints are increasing. The causes of tile defects include problems such as the selection of tile adhesive and lack of adhesive strength, the carelessness of the installer, the base surface, and the absorption rate of the tile. Therefore, in this study, an adhesive construction method using tile adhesives with high resistance to deformation of floors and tiles was studied. In addition, the properties and construction methods of tile adhesives were evaluated.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2003년도 추계학술대회논문집
• /
• pp.121-124
• /
• 2003

A new form-joining process with the aid of an adhesive is proposed in which an epoxy adhesive is applied to a sheet metal pair, and before it cures the pair is clinched to cause the geometric constraint in the form of a protrusion. In order to reduce the forming load and the height of protrusions, a new die and punch set with a very small clearance was devised to reduce the depth of drawing and the forming load. Taguchi method was employed to find the optimal values of design parameters. To implement each case of the orthogonal array, the finite element method was used. The experiments showed that on the tensile-shear test, the bonding strength of the new form-joining process with an epoxy adhesive is approximately the same as that of the resistance spot welding; and in comparison with the other two form-joining processes with an epoxy adhesive, the height of protrusions was reduced by more than 65 percent and the forming load by 50 percent.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2004년도 추계학술대회 논문집
• /
• pp.860-864
• /
• 2004

This article discusses the use of pulse-echo ultrasonic testing for the stress analysis of adhesive bonds between metal sheets. The method is based on the measurement of the reflection wave at the metal/adhesive interface. After describing briefly the physical aspects of the phenomenon, an index is defined to detect defective zone of the joint(both for the lack of adhesive and for insufficient adhesion); the influence of the experimental variables(variables stress...) on the measurement is discussed. By means of a control experiment it is shown that Stress Variation in Adhesive Joints are separate to be distingguished. In this paper, Quantitative Nondestructive Evaluation in Adhesive Joints are together with Ultrasonic Testing and Finite Element Method.

• 한국해양공학회지
• /
• 제24권1호
• /
• pp.146-152
• /
• 2010

Recently, the applied frequency of composite materials was increased from the viewpoint of lightweight, high strength and low cost when a leisure boat and a fishing boatwere built. However, studies on the mechanical properties of composite material with ship are rare. Specially, a leisure boat and fishing boat with FRP had been built by hand lay-up method. However, the vacuum infusion method is rising recently for ship building. The manufactured these FRP plates were combined by using the adhesive. Therefore, in this study Cleavage peel strength, Shear strength and fatigue limit of adhesive bonds by tensileloading were estimated. From test results, the strengths of FRP specimens made by the vacuum infusion method are higher than that of the hand lay-up method.

• Journal of the Korean Association of Oral and Maxillofacial Surgeons
• /
• 제31권5호
• /
• pp.427-435
• /
• 2005

The purpose of this study was to compare clinical availability of fibrin adhesive technique with microneural suture technique. We applicated fibrin adhesive technique and microneural suture technique on cut sciatic nerve in rat and used to Compound muscle action potential of rat thigh muscle compartment and histologic finding for comparision of clinical availability. The results were as following. 1. Using latency and amplitude in Compound muscle action potential test, we compared microneural suture technique with fibrin adhesive technique for nerve regeneration effect. the means was slightly different between two method. but there's no statistically significant differences. 2. Histologic finding was similar in microneural suture technique and fibrin adhesive technique for regeneration of axon and myelin sheath in destruction site after nerve anastomosis. These results showed that the efficacy of fibrin adhesive technique was similar to that of conventional microneural suture technique. Moreover, fibrin adhesive technique is decreased operating time and imporved of incapability of accessment in conventional suture technique. Therefore this technique is a useful method to nerve anastomosis in nerve enervation and neurotransplantation.

• 대한기계학회논문집A
• /
• 제26권12호
• /
• pp.2662-2669
• /
• 2002

Recently structural applications of adhesive bonding method have been increased extensively in automobile industry. Adhesively-bonded joints which are used in automobile field are exposed to various environmental conditions. In this study, several environmental factors were concerned to evaluate their effects on the adhesive strength such as air temperature, water temperature, exposed time in water. The specimens are exposed for 1, 10 and 100 hours at various air temperatures to evaluate the effects of the air and water temperature on the adhesive strength. It is proved that the adhesive strength decrease with rising the air and water temperature, and the adhesive strength decrease steeply at the higher temperature with increasing the exposure time in water.