• 접착 및 계면
• /
• 제3권2호
• /
• pp.40-44
• /
• 2002

본 실험에서는 고무-황동 도금 스틸 코드 복합체의 접착성에 미치는 미가류 복합체의 방치 기간과 가류 복합체의 열노화의 영향을 검토하였다. 또한 이런 방치 조건에 따른 접착력 변화가 타이어 내구력에 어떤 영향을 미치는지를 평가하였다. PAD 접착 시편을 사용하여 박리 접착 강도를 측정하였다. 미가류 복합체의 방치 기간은 공장 조건에서 최대 35일이고 가류 복합체의 열노화는 $85^{\circ}C$ 항온조에서 5, 10일간 실시하였다. 박리 접착 강도는 방치일수가 길수록 하락하는 경향을 보였다. 또한 열노화 기간이 길수록 그 값은 낮았다. 박리 접착 강도가 낮을수록 타이어 내구력도 낮았고, 그 주된 원인이 수분과 열에 의한 노화가 고무와 스틸 코드의 접착력을 하락시켜 코드와 고무의 계면에서 파괴가 일어났기 때문이라는 것을 SEM관찰과 내구력 평가로 확인할 수 있었다. 즉, 스틸 코드 표면의 부식이나 접착증의 노화가 접착강도 하락에 크게 영향을 미치고 그 결과 타이어의 내구력 하락에도 직접적인 영향을 미친다는 것을 알 수 있었다.

• Journal of Pharmaceutical Investigation
• /
• 제29권2호
• /
• pp.127-136
• /
• 1999

In order to eliminate demerits of conventional dosage forms, dipotassium glycyrrhizate was formulated as a slim mucoadhesive film type dosage form. The mucoadhesive drug layer gel containing dipotassium glycyrrhizate was prepared using $Noveon^{\circledR}$ AA-1, hydroxypropylcellulose-M, ethylcellulose N 100 and citric acid, and the protective layer gel by using ethylcellulose N 100, $Eudragit^{\circledR}$ RS and castor oil. The viscosity of drug layer gel of mucoadhesive film was enhanced as the increased amount of $Noveon^{\circledR}$ AA-1 or hydroxypropyl cellulose-M. The drug content was unifonnly $1160{\pm}14.6\;{\mu}g$, and was varied within 3.5%. The optimum film dosage form showed a good fluidity and malleability of drug layer, with 179 g of thickness, pH 5.7, 411 min of in vitro adhesion time and 172 g in gravity adhesive strength. The release time of drug from the mucoadhesive film was significantly shorter but was delayed when polymers such as ethylcellulose was added. From these results, the new mucoadhesive film may be effective for the treatment of aphthous stomatitis.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2010년도 춘계학술대회 논문집
• /
• pp.43-43
• /
• 2010

we have investigated the field emission characteristics of the CNT/TEOS hybrid thin films fabricated by a spray method. It is found that the CNT/TEOS hybrid emitters show high current density, low turn on field, and long-term emission stability compared to the CNT emitters. These efficient field emission characteristics of the CNT/TEOS hybrid emitters are attributed to the TEOS sol, acting as a protection layer of nanotube emitter by surrounding the nanotube tip as well as a binder material to enhance the adhesion of nanotube emitters to the substrate. Therefore, the CNT/TEOS hybrid emitters could be utilized as an alternative for the efficient and reliable field emitters.

• International Journal of Precision Engineering and Manufacturing
• /
• 제7권4호
• /
• pp.47-50
• /
• 2006

SCM415 alloy was implanted with nitrogen ions using plasma source ion implantation (PSII), at a dose range of $1{\times}10^{17}\;to\;6{\times}10^{17}\;N^+cm^{-2}$ Auger electron spectrometry (AES) was used to investigate the depth profile of the implanted layer. Friction and wear tests were carried out on a block-on-ring wear tester. Scanning electron microscopy (SEM) was used to observe the micro-morphology of the worn surface. The results revealed that after being implanted with nitrogen ions, the frictional coefficient of the surface layer decreased, and the wear resistance increased with the nitrogen dose. The tribological mechanism was mainly adhesive, and the adhesive wear tended to become weaker oxidative wear with the increase in the nitrogen dose. The effects were mainly attributed to the formation of a hard nitride precipitate and a supersaturated solid solution of nitrogen in the surface layer.

• 비파괴검사학회지
• /
• 제30권3호
• /
• pp.236-243
• /
• 2010

Fiber Bragg grating(FBG) sensor arrays can be used to monitor the mechanical behavior of the large composite structures such as wind turbine rotor blades and aircrafts. However, brittle FBG sensors, especially multiplexed FBG sensors are easily damaged when they are installed in the flexible structures. As a protection of brittle FBG sensors, epoxy packaged FBG sensors have been presented in this paper. Finite element analysis and experiments were performed to evaluate the effects of adhesives, packaging materials and the bonding layer thickness on the strain transmission. Two types of epoxy were used for packaging FBG sensors and the sensor probes were attached with various bonding layer thickness. It was observed that thin bonding layer with high elastic modulus ratio of the adhesive to packaging provided good strain transmission. However, the strain transmission was significantly decreased when elastic modulus of the adhesive was much lower than the packaged FBG sensor probe's one.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회A
• /
• pp.238-243
• /
• 2007

This paper is designed to estimate the adhesion strength of coating layer on galvannealed steel sheet using lap shear test. The single lap shear test is the most commonly used standard test for determining the strength of medium-strength and high strength bonds. The bond strength of bonded single lap joints on subjecting the substrates to loads is determined by lap shear forces in the direction of the bonded joint. In this study, specimen for adhesion strength test was made to attach coated sheet to cold rolled sheet and were heated in temperature of 180 for 20minutes. After test, detached parts of coatings on coated sheet were observed using SEM and EDX to identify substrate and complete detachment. The tested results showed that adhesive strength of coating is unrelated to anisotropy of sheet and is difficult to be extracted using conventional theory because of fine cracks of coating layers which were created during annealing process.

• Steel and Composite Structures
• /
• 제20권5호
• /
• pp.999-1022
• /
• 2016

The use of Carbon Fiber Reinforced Polymer (CFRP) to strengthen steel structures has attracted the attention of researchers greatly. Previous studies demonstrated bonding of CFRP plates to the steel sections has been a successful method to increase the mechanical properties. However, the main limitation to popular use of steel/CFRP strengthening system is the concern on durability of bonding between steel and CFRP in various environmental conditions. The paper evaluates the performance of I-section steel beams strengthened with pultruded CFRP plate on the bottom flange after exposure to diverse conditions including natural tropical climate, wet/dry cycles, plain water, salt water and acidic solution. Four-point bending tests were performed at specific intervals and the mechanical properties were compared to the control beam. Besides, the ductility of the strengthened beams and distribution of shear stress in adhesive layer were investigated thoroughly. The study found the adhesive layer was the critical part and the performance of the system related directly to its behavior. The highest strength degradation was observed for the beams immersed in salt water around 18% after 8 months exposure. Besides, the ductility of all strengthened beams increased after exposure. A theoretical procedure was employed to model the degradation of epoxy adhesive.

• Applied Microscopy
• /
• 제46권3호
• /
• pp.150-154
• /
• 2016

The ultrastructure of fertilized egg envelope from Pseudobagrus fulvidraco belongs to Bagridae was investigated using light and electron microscopes. The fertilized egg was compressed spherical, light-yellowish, demersal, and adhesive. The size of fertilized egg is about $1.85{\pm}0.13mm$, perivitelline space is not well developed, and there were no appendicular structures on the outer surface of egg envelope and oil droplets in vitelline membrane under light microscope. The micropyle was located in the animal pole of fertilized egg. Adhesive reticular fiber was covered fertilized egg envelope. The thickness of egg envelope was about $3.7{\sim}4.2{\mu}m$, and the egg envelope consisted of two layers: an outer, electron-dense adhesive fibers layer and an simple inner layer with pore. Therefore, the ultrastructure of cross section of the fertilized egg envelope showed species specificity, but studies on the other species belongs to Bagridae were need to get correct information about common traits in family.

• 센서학회지
• /
• 제16권5호
• /
• pp.325-330
• /
• 2007

For the application to optic devices, wafer level package including spacer with particular thickness according to optical design could be required. In these cases, the uniformity of spacer thickness is important for bonding strength and optical performance. Packaging process has to be performed at low temperature in order to prevent damage to devices fabricated before packaging. And if photosensitive material is used as spacer layer, size and shape of pattern and thickness of spacer can be easily controlled. This paper presents polymer bonding using thick, uniform and patterned spacing layer of SU-8 2100 photoresist for wafer level package. SU-8, negative photoresist, can be coated uniformly by spin coater and it is cured at $95^{\circ}C$ and bonded well near the temperature. It can be bonded to silicon well, patterned with high aspect ratio and easy to form thick layer due to its high viscosity. It is also mechanically strong, chemically resistive and thermally stable. But adhesion of SU-8 to glass is poor, and in the case of forming thick layer, SU-8 layer leans from the perpendicular due to imbalance to gravity. To solve leaning problem, the wafer rotating system was introduced. Imbalance to gravity of thick layer was cancelled out through rotating wafer during curing time. And depositing additional layer of gold onto glass could improve adhesion strength of SU-8 to glass. Conclusively, we established the coating condition for forming patterned SU-8 layer with $400{\mu}m$ of thickness and 3.25 % of uniformity through single coating. Also we improved tensile strength from hundreds kPa to maximum 9.43 MPa through depositing gold layer onto glass substrate.

• 치위생과학회지
• /
• 제9권4호
• /
• pp.405-412
• /
• 2009

본 연구는 도재소부용 비귀금속에 Au 코팅 층을 형성하고, Au 코팅 층이 금속-도재의 결합력에 미치는 영향을 알아보고자 2출 굴곡 시험 후에 SEM/EDS 방법으로 조사하여 비교하였다. 1. Ni-Cr ally 군과 Co-Cr alloy 군, 그리고 Ti 군의 절단면 시편의 전자현미경 사진에서 Au 코팅 층은 산화층의 확산을 제어하는 것으로 관찰되었다. 2. 2축 굴곡 시험 후에 EDS 분석 결과 Ni-Cr alloy 군과 Co-Cr alloy 군에서 Si 함량은 Au 코팅 층을 형성한 시편에서 약간 감소하였고, 결합실패의 형태는 cohesive failure와 adhesive failure가 혼재된 양상으로 관찰되었다. 3. Ni-Cr alloy 군과 Co-Cr alloy 군에서 Au 코팅 층은 도재-금속 결합력에 미치는 영향은 미미하였다. 4. Ti 군의 결합실패 형태는 Ni-Cr alloy 군과 Co-Cr alloy 군에 비해서 adhesive failure 양상이 두드러지게 관찰되었고, Au 코팅 층은 도재-금속 결합력에 영향을 미치지 않았다. 이상의 결과 비귀금속에 적용한 Au 코팅은 산화층의 확산을 제어 하는 것으로 관찰 되었으나, 금속-도재 간의 결합력 증징에 미치는 효과는 미미하였다. Au 코팅을 이용하여 금속-도재 간의 결합력 증진을 위해서는 많은 연구가 지속되어야 할 것으로 사료된다.