• Nuclear Engineering and Technology
• /
• v.46 no.4
• /
• pp.547-556
• /
• 2014

Korea expects a shortage in storage capacity for spent fuels at reactor sites. Therefore, a need for more metal and/or concrete casks for storage systems is anticipated for either the reactor site or away from the reactor for interim storage. For the purpose of interim storage and transportation, a dual purpose metal cask that can load 21 spent fuel assemblies is being developed by Korea Radioactive Waste Management Corporation (KRMC) in Korea. At first the gamma and neutron flux for the design basis fuel were determined assuming in-core environment (the temperature, pressure, etc. of the moderator, boron, cladding, $UO_2$ pellets) in which the design basis fuel is loaded, as input data. The evaluation simulated burnup up to 45,000 MWD/MTU and decay during ten years of cooling using the SAS2H/OGIGEN-S module of the SCALE5.1 system. The results from the source term evaluation were used as input data for the final shielding evaluation utilizing the MCNP Code, which yielded the effective dose rate. The design of the cask is based on the safety requirements for normal storage conditions under 10 CFR Part 72. A radiation shielding analysis of the metal storage cask optimized for loading 21 design basis fuels was performed for two cases; one for a single cask and the other for a $2{\times}10$ cask array. For the single cask, dose rates at the external surface of the metal cask, 1m and 2m away from the cask surface, were evaluated. For the $2{\times}10$ cask array, dose rates at the center point of the array and at the center of the casks' height were evaluated. The results of the shielding analysis for the single cask show that dose rates were considerably higher at the lower side (from the bottom of the cask to the bottom of the neutron shielding) of the cask, at over 2mSv/hr at the external surface of the cask. However, this is not considered to be a significant issue since additional shielding will be installed at the storage facility. The shielding analysis results for the $2{\times}10$ cask array showed exponential decrease with distance off the sources. The controlled area boundary was calculated to be approximately 280m from the array, with a dose rate of 25mrem/yr. Actual dose rates within the controlled area boundary will be lower than 25mrem/yr, due to the decay of radioactivity of spent fuel in storage.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.25 no.3
• /
• pp.245-258
• /
• 2012

ILM(incremental launching method) is a way of construction, installing a girder producing spot behind the abutment, making the bridge girder infilled with concrete continuously and launching with using by jack. The superstructure of the bridge constructed by this method is temporarily located on the center of the span and the supporting points under construction. Therefore, the sections are structurally undergone maximum positive moment, maximum negative moment, and maximum shear force arising from self weight. On the other hand, launching nose is attached to the front of the girder to decrease the cantilever effect. The magnitude of this temporary stress creating on the upper section is dependent upon the launching nose's characteristics. This study has proposed an analysis formula simplified on the assumption that the launching nose section is a quasi-equivalent section(rigid; equivalent section, weight; tapered section) in order to ensure the accuracy of the analysis formula and improve its usage with reference to the interaction between the launching nose and the upper section; and a prismatic analysis formula modified by displacing a diaphragm's weight by a concentrated load in order to improve the accuracy of the existing analysis formula that assumes the launching nose section as the equivalent section. To judge the accuracy and usage of two analysis formulas proposed, we have compared and analyzed computational structural analysis programs and existing analysis formulas based on actual ILM bridge data. As a result, all of two reveal the superior accuracy and also their usage has been improved by the simplification of analysis formulas.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.24 no.4
• /
• pp.10-17
• /
• 2020

The recent earthquake in Korea caused large and small damages to many school building. School building is an important building that is used as a shelter in the event of disaster. Among the seismic retrofit methods, the internal steel braced frame type method is used for its relatively easy construction and excellent performance. In this study, the maximum shear force and displacement were compared and examined by applying the brace frame to existing concrete school buildings. As a result, we verified the adequacy of the analytical model and compared and examined the effect of brace-height ratio on the span of the existing school buildings. The adequacy of the maximum shear force and displacement relationship can be confirmed in the model with a length of 0.3. In addition, seismic frame was applied to the actual non-seismic reinforced concrete school building, and the seismic performance was evaluated by nonlinear static analysis(Push-over analysis) according to the ratio of brace-height. As a result, the increase of the brace-height according to the brace-height ratio has the effect of increasing the maximum shear force and maximum load at the performance point. But the collapse of the braced frame due to the increase in the lateral stiffness occurred, indicating that seismic retrofit according to the proper brace-height is necessary. Therefore, in the seismic retrofit design of brace frame of existing school building, it is necessary to select the proper brace-height after retrofit analysis according to the brace-height ratio.

• Journal of Gifted/Talented Education
• /
• v.19 no.2
• /
• pp.353-380
• /
• 2009

The significant reason for studying computer science lies in the efficient resolution of various problems which can arise in actual life. Consequently, algorithm education is very important in the computer science and plays a great part in helping to enhance the creative ability to solve problems and to improve the programming ability. However, the current algorithm education at an computer science educational institute for the gifted has inadequate systematic quality and is only treated as a part of programming education. From this perspective, this paper carried out following studies in order to design the algorithm education for elementary computer science prodigies. First, the core educational contents was selected by extracting the common elements from existing books related to algorithm education, common study contents on algorithm lesson websites and the study area of ACM's computer algorithm. Second, using the development criteria and selected educational contents, the educational theme for the If weeks load was set. Additionally, the algorithm educational contents were designed for the elementary computer science prodigy based on such theme. Third, the activity site for the use of prodigy educational institute was developed with the background in the educational contents for the elementary computer science prodigy. Fourth, the Delphi analysis technique was used to verify the appropriateness of contents and activity site developed in this paper. It was carried out in 2 separate processes where the first process verified the design of educational contents, and the second process verified the appropriateness of developed activity site.

• Journal of the Korean Society of Safety
• /
• v.35 no.5
• /
• pp.49-58
• /
• 2020

In domestic construction sites, when installing steel pipe scaffolding and system scaffolding, the guardrails are installed after the installation of the work platforms. This conventional guardrail system (CGS) is always exposed to the risk of falls because the safety railing is installed later. In order to prevent fall disasters during erecting and dismantling scaffolds, it is necessary to introduce the advanced guardrail system (AGS) which installs railings in advance of climbing onto a work platform. For the introduction of the AGS, the structural performance of the system scaffolding applying the CGS and the AGS was compared and evaluated. The structural analysis of the system scaffold (height: 31 m and width: 27.4 m) with AGS confirmed that structural safety was ensured because the maximum stress of each element of the system scaffolding satisfies the allowable stress of each element. As a result of performance comparison of CGS and AGS for each element, the combined stress ratio of vertical posts in AGS was 6.4% lower than that of CGS. In addition, in the case of ledger and transom, the combined stress ratios of AGS and CGS were almost the same. The compression test of the assembled system scaffolding (three-storied, 1 bay) showed that the AGS had better performance than the CGS by 9.7% (8.91 kN). The cross bracing exceeds the limit on slenderness ratio of codes for structural steel design. But the safety factor for the compressive load of the cross bracing was evaluated as meeting the design criteria by securing 3 or more. In actual experiments, it was confirmed that brace buckling did not occur even though the overall scaffold was buckled. Therefore, in the case of temporary structures, it was proposed to revise the standards for limiting on slenderness ratio of secondary or auxiliary elements to recommendations. This study can be used as basic data for the introduction of AGS for installing guardrails in advance at domestic construction sites.

• Journal of Navigation and Port Research
• /
• v.33 no.1
• /
• pp.27-33
• /
• 2009

Estimation of the buckling and ultimate strength of a continuous stiffened plate subjected to combined transverse compression and lateral pressure is of high importance to ensure the safety of ship structures, particularly for the bottom plating under a deep draft condition For example, bottom plating of bulk carriers is subjected to transverse thrust caused by the bending of double bottom structure and the direct action of pressure on the side shells. Most of experimental tests, theoretical approach and numerical researches have been performed on the buckling and ultimate strength behaviour of plates or stiffened plates under combined compression and lateral pressure. With regard to stiffened panels, however, most of studies have been concerned with the load conditions of combined longitudinal thrust and lateral pressure, while fewer studies have been performed for the combined transverse thrust and lateral pressure. In addition, the previous researches are mainly concerned with an isolated rectangular plate simply supported along the all edges, whereas actual ship plating is continuous across the transverse frames and heavy girders. In the present paper, a series of elastoplastic large deflection FEA on a continuous stiffened plate is performed and then clarify the characteristic of collapse mode and explain the effect of transverse compression.

• Journal of Preventive Medicine and Public Health
• /
• v.33 no.4
• /
• pp.436-448
• /
• 2000

Objectives : To identify the factors affecting users' satisfaction with the Order Communicating System(OCS) and to highlight the factors important for the successful establishment of OCS. Methods : A Users Satisfaction survey was sent to 4,513 people, consisting of 1,503 doctors, 2,379 nurses, 255 pharmacists and 370 administrative workers in 16 hospitals which had introduced OCS. The response rate was 63.9%. Measurement of users' satisfaction was peformed with the instrument which was used in Doll's study. Some aspects of Doll's instrument were adjusted according to the aims of this study. The classifying sections of this survey included age, job and status classification, computer experience, OCS education, duration of daily OCS use, type of order entering, number of personnel in the Hospital Information System's department, cost of OCS, problem frequency, proportion of work managed by hand, OCS type, and Hospital establishment type. Results : There was a positive correlation between satisfaction level and managerial status throughout all job classifications. Irrespective of the importance of OCS education as a factor relating to users' satisfaction, the additional work load caused by OCS lowered users' satisfaction. Different factors affected users' satisfaction according to job and status classification. The composition of factors affecting the pharmacist and administrative worker satisfaction levels was simpler than that of the doctor and nurse levels. There were no statistically significant differences between the actual computer experience duration of daily OCS use and users' satisfaction with OCS. Conclusions : There was an understandable relationship between users' attitude to OCS and factors affecting users' satisfaction. The results of this study could be used as a basis for the successful expansion of the operation of OCS. But more detailed studies on users' satisfaction and further improvements of methodologies are required for the successful establishment of OCS.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.10
• /
• pp.554-561
• /
• 2016

In this study, loading tests and a strength evaluation of the bogie frame were conducted to verify the structural safety of the bogie system in an intermodal tram, which runs with cars on a road track. The loads were calculated taking into account the features of the road track with many sharp curves and steep gradients, which are different from the track of conventional railway. They were compared with the loads specified in the previous standard specifications. After the comparison, it was confirmed that the loads acting on the bogie system operating on a road track are slightly different from the specified loads. The specified vertical load of the standard specification for all kinds of trains is conservative, but the specified lateral and longitudinal loads are less than the calculated loads. The application of the actual loads was proven to be reasonable in the development of a new railway system. Based on the defined loads, the bogie frame was fabricated on which strain gauges were attached. It was set on the large loading frame so that the stresses could be measured when loads were applied by hydraulic actuators. After measuring the stresses, it was shown that they were below the allowable stress, which verified the structural safety of the bogie frame.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.52 no.7
• /
• pp.63-73
• /
• 2015

In the end to end data transfer protocols, it is very important to correctly estimate available bandwidth. In UDT (UDP based Data Transfer), receiver estimates the MTR (Maximum Transfer Rate) of the current link using pair packets transmitted periodically from sender and, then sender finally decides the MTR through EWMA (Exponential Weighted Moving Average) algorithm. Here, MTR has to be exactly estimated because available bandwidth is calculated with difference of MTR and current transfer rate. However, when network is congested due to traffic load and where competing flows are coexisted, it bring about a severe fairness problem. This paper proposes a congestion degree based MTR estimation algorithm. Here, the congestion degree stands a relative index for current congestion status on bottleneck link, which is calculated with arriving intervals of a pair packets. The algorithm try to more classify depending on the congestion degree to estimate more actual available bandwidth. With the network simulation results, our proposed method showed that the fairness problem among the competing flows is significantly resolved in comparison with that of UDT.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.7 no.3
• /
• pp.243-254
• /
• 2019

In this study, problems of the waterproofing methods in which water leakage occurs in the upper slab of the underground parking lot of apartment houses and the requirements considering the characteristics of the upper slab, and selected the appropriate performance(proposal) for the composite polyurea process are reviewed. As a result of the study, it is necessary to review performance such as responsiveness to upper slab of the multi-unit underground parking lot that is comprised of (1) crack and behavior responsiveness, (2) surface integrity, (3) vertical watertight stability, (4) pressure layer construction, (5) impact and pressure response and (6) vehicle moving load. As a result of evaluating 5 items corresponding to the requirements for the soft and hard complex polyurea, all of them were found to meet the conditions, and each materials were improved by compounding the materials that had problems when applying a single-ply method, thereby clarifying the advantages and disadvantages of the material property. However, in order to apply to the actual site, additional evaluation on site applicability such as mock-up evaluation should be conducted, and subsequent studies on the applicability of the market through review of economic feasibility and maintenance is required.