• 한국식품저장유통학회지
• /
• 제9권2호
• /
• pp.240-247
• /
• 2002

세정수로서의 전해산화수 효능을 증대시키기 위하여 다양한 식품첨가제를 첨가하여 제조한 $0^{\circ}C$ 이하의 세정수에 대한 냉각특성, 살균 및 갈변억제 효과를 조사하였다. 식품첨가제의 첨가비율은 NaCl 0.85%(w/v), ethanol 0.5%(v/v), 레몬과즙 0.5%(v/v), 유자과즙 0.5%(v/v), polysorbate 80은 1 ppm으로 결정하였다. 미생물 사멸효과는 초기 5.63$\times$$10^{ 8}$ CFU/mL인 Escherichia coli KCTC 1039가 모든 첨가구에서15~30초 이내에 전부 사멸하였으며, Bacillus cereu KCTC 1012는 polysorbate 80 및 ethanol 첨가구에서 2분 후, Lactobacillus plantarum KCTC 3108은 polysorbate 80, 유자 및 레몬과즙 첨가구에서 30초만에, 그리고 Erwinia carotovorasubsp. carotovora KCTC 2776은 polysorbate 80 및 레몬과즙 첨가구에서 30초만에 사멸하는 효과를 나타내었다. 갈변억제효과는 polyphenol oxidase의 활성을 측정하여 비교한 결과, asnrbic acid 0.5% 첨가구에 5분간 침지하였을 때 57%의 활성저해를 보인 반면, 25%의 저해능을 보인 polysorbate 80 첨가구를 제외한 모든 처리구에서 62~84%의 높은 활성저해 효과를 보였으며, 그 중에서도 NaCl 및 유자과즙 첨가구에서 30분 침지시에 각각 64, 91 units로 가장 낮은 활성을 보여주었다. 절단 감자를 30분간 침지처리한 후의 색도에서도 대부분의 처리구에서 색차($\Delta$E)가 3 이하를 나타내었다.다.

• 한국응용과학기술학회지
• /
• 제38권1호
• /
• pp.19-28
• /
• 2021

부식은 환경과의 반응에 의한 금속의 열화이다. 이는 완전히 제거하기가 어렵다. 부식은 보호장벽이 파괴 된 후 빠르게 진행되며 매트릭스로의 금속 양이온 확산, 산화물 형성과 국소 pH 변화 같은 금속 표면과 국소 환경의 조성과 특성을 변경하는 여러 반응이 일어난다. 강과 철의 부식에 대한 연구는 이론적, 실제적 관심사이며 상당한 관심을 받고 있다. 산업용 산세척, 산 스케일 제거, 세척 및 유정 산성화에 널리 사용되는 산 용액은 금속 재료에 대한 부식 공격을 억제하기 위해 부식 억제제를 사용해야한다. 녹을 물리적으로 제거하려면 고가의 특수 장비가 필요하며 이를 화학적으로 제거하면 부식을 유발하거나 금속의 수명을 단축 할 수 있다. 본 연구에서는 퍼머 환원제와 킬레이트 개념을 적용하여 화장품 및 식품소재를 이용한 친환경 녹 세정제를 개발하였고 산업 및 온수 관, 각종 산업 기기의 녹을 제거하기 위해 적용하여 보았다. 그 결과, 녹 세정제는 기존 처리 방식에 비해 녹을 더 효과적이고 안전하게 제거하는 것으로 나타났다. 동일한 시간에서 녹 제거 효율은 기존의 방법보다 공업용 배관의 경우 1.75 ~ 2.5 배, 보일러 온수용 배관의 경우 1.56 ~ 2.2 배 우수하였다.

• 한국안광학회지
• /
• 제16권3호
• /
• pp.255-264
• /
• 2011

목적: 인공눈물, 렌즈용 다목적 용액, 화장품, 근골격계 용제에 널리 사용되고 있는 히알루론산(hyaluronic acid, HA)의 콘택트렌즈의 습윤성과 착용감에 대한 효과를 알아보기 위해 HA가 첨가된 콘택트렌즈(+HA)와 HA가 첨가되지 않은 렌즈(-HA)를 임상 평가하여 비교하였다. 방법: 안질환이 없는 대학생 28명을 대상으로 하여 4주 동안 우안에는 HA가 첨가된 렌즈(+HA, With HA)를 좌안에는 HA가 첨가되지 않은 렌즈(-HA, Without HA)를 착용하여, 좌안을 대조군으로 우안을 비교하였다. 이 때, 렌즈 도수는 등가구면으로 처방하고, 자동굴절검사기를 이용해 덧댐굴절검사를 한 뒤 2주와 4주 동안 렌즈 착용 후 눈물검사, 전안부 검사, 피팅 용이성 평가, 표면 습윤성 검사, 설문조사를 시행하였다. 결과: 히알루론산이 첨가된 렌즈(+HA)가 -HA 렌즈보다 우수한 습윤성을 보였으며, 눈물량은 +HA 렌즈 착용자에서는 4주 동안 차이가 크지 않았지만, -HA 렌즈 착용자에서는 4주가 되면서 눈물량이 줄어드는 결과를 보였다. +HA와 -HA 렌즈 착용자의 충혈정도는 차이를 보이지 않았으며, 렌즈 피팅은 +HA 렌즈에서 용이한 것으로 나타났다. 설문조사 결과에서 착용감, 습윤감, 세척의 용이성과 건조감은 +HA 렌즈가 -HA 렌즈에 비해 우수한 결과를 보였으나, 충혈정도와 렌즈 취급성은 차이가 적은 것으로 나타났다. 결론: 히알루론산이 첨가된 소프트콘택트렌즈(+HA)는 HA가 첨가되지 않은 소프트콘택트렌즈(-HA)에 비해 렌즈착용에 따른 표면 습윤성을 높임으로써 착용감을 증진시키는 것으로 사료된다.

• 한국분말재료학회지
• /
• 제16권5호
• /
• pp.336-341
• /
• 2009

To produce alloy powders with only Sm$_2$Fe$_{17}$ single phase by reduction-diffusion (R-D) method, the effect of excess samarium oxide on the preparation of Sm-Fe alloy powder during R-D heat treatment was studied. The quantity of samarium oxide was varied from 5% to 50% whereas iron and calcium were taken 0% and 200% in excess of chemical equivalent, respectively. The pellet type mixture of samarium, iron powders and calcium granulars was subjected to heat treatment at 1100$^{\circ}C$ for 5 hours. The R-D treated pellet was moved into deionized water and agitated to separate Sm-Fe alloy powders. After washing them in deionized water several times, the powders were washed with acetic acid to remove the undesired reaction products such as CaO. By these washing and acid cleaning treatment, only 0.03 wt% calcium remained in Sm-Fe alloy powders. It was also confirmed that the content of unreacted $\alpha$-Fe in Sm$_2$Fe$_{17}$ matrix gradually decreased as the percentage of samarium oxide is increased. However, there was no significant change above 40% excess samarium oxide.

• 한국환경농학회지
• /
• 제32권2호
• /
• pp.108-116
• /
• 2013

BACKGROUND: Certain crop-based waste materials have been recognized as cost-effective and highly efficient adsorbents for removal and recovery of different kind of heavy metals from aqueous solutions. The ability is strongly attributed to the carboxyl functional group of some pectin substances such as galacturonic acid often found in fruit peels. The present manuscript was aimed at assessing the potential applicability of banana peel for metal removal from contaminated waters. METHODS AND RESULTS: As revealed by laboratory investigations, banana peel contains pectin (10-21%), lignin (6-12%), cellulose (7.6-9.6%), and hemicelluloses (6.4-9.4%). The pectin extraction is reported to have glucose, galactose, arabinose, rhamnose, xylose, and galactouroninc acid. Several studies conducted under different conditions proved that banana peel is capable of adsorbing 5.71, 2.55, 28.00, 6.88, 7.97, and 5.80 mg/g of $Cd^{2+}$, $Co^{2+}$, $Cu^{2+}$, $Ni^{2+}$, $Pb^{2+}$, and $Zn^{2+}$, respectively, from aqueous solutions. Adsorption capacity is, however, dependent upon several factors including solution pH, dose of adsorbent and metal concentration, contact time and shaking speed. CONCLUSION(S): Since the annual world production of banana exceeds 100 million tons, about 40 million tons of banana peel (40% of total weight of the fresh fruit) remains vastly unused. Exploring a sound technology with banana peel would therefore, not only address the much needed sustainable tool for cleaning contaminated waters, but of course bring an additional value to the banana industry worldwide.

• 대한전기학회논문지:시스템및제어부문D
• /
• 제51권9호
• /
• pp.423-430
• /
• 2002

The fabrication and experimentation of multi-channel electrodes which enable detecting and recording of multi-site neuronal signals have been investigated. A multi-channel electrode array was fabricated by depositing 2000${\AA}$ thick Au layer on the 1000${\AA}$ thick Ti adhesion layer on a glass wafer. The metal paths were patterned by wet etching and passivated by depositing a PECVD silicon nitride insulation layer to prevent signals from intermixing or cross-talking. After placing a thin slice of rat cerebellar granule cell in the culture ring located in central portion of the multi-channel electrode plate, a neuronal signal from an electrode which is in contact with the cerebellar granule cell has been detected. It was found that the electrode impedance ranges 200㏀∼1㏁ and the impedance is not changed by cleaning with nitric acid. Also, the impedance is inversely proportion to the exposed electrode area and the cross-talk is negligible when the electrode spacing is bigger than 600$\mu\textrm{m}$. The amplitude and frequency of the measured action potential were 38㎷ and 2㎑, which are typical values. From the experimental results, the fabricated multi-channel electrode array proved to be suitable for multi-site neuronal signal detection for the analysis of a complicated cell network.

• 한국의류학회지
• /
• 제19권6호
• /
• pp.955-967
• /
• 1995

This study was performed to investigate the physical and chemical properties of the 5 kinds of fabrics dyed with persimmon juice and undyed fabrics. The difference between dyed and undyed fabrics was checked experimentally. Obtained results are as follows. 1. Bending length and flex stiffness were increased after dyeing, and tensile strength of waif i3l fabrics except Ramie was also increased. 2. Abrasion resistance was improved in Ramie and Hemp after dyeing but the rest of fabrics were decreased. 3. Crease resistance of dyed fabrics was roughly worse than that of undyed fabrics. 4. Air permeability remarkably increased after dyeing and this fact estabilished that the traditional Gal-01 was cool clothing. 5. Water repellency in Cotton 1 and Polyester rises but the rest of fabrics were not changed. Therefore it is found that this repellency related to the their fabric counts. 6. Blocking effect of UV light and visible ray was increased in all dyed fabrics. Especially dyed Cotton 1 and Polyester blocked UV light almost perfectly. 7. The colorfastness to soaping and sunlight was proved to less than 3 grade in all fabrics after dyeing. It indicates that this colorfastness became worse owing to dyeing. 8. The colorfastness to dry cleaning and water was decided to more than 3 grade in all fabrics. 9. The colorfastness of the dyed fabrics to sweat after exposing to man-made acid sweat solution was good so that was decided above 3 grade. However after exposing to man-made alkalic sweat solution it became worse owing to dyeing.

• 마이크로전자및패키징학회지
• /
• 제15권2호
• /
• pp.17-21
• /
• 2008

Sn-Cu계 솔더 범프에서 무전해도금법을 이용한 범프 형성에 대한 연구를 하였다. $20{\mu}m$ via에 전기도금법으로 구리를 채운 웨이퍼 위에 ball형태의 범프를 형성하기 위하여 구리와 주석을 도금하여 약 $10{\mu}m$높이의 범프를 형성하였다. 구리 범프 형성 시 via위에 선택적으로 도금하기 위하여 활성화 처리 후 산세처리를 실시하고 무전해 도금액에 안정제를 첨가하였다. 무전해도금법을 이용하여 주석 범프 형성 시 도금층이 구리 범프에 비해 표면의 균일도가 벌어지는 것으로 관찰되었지만 reflow공정을 실시한 후 ball 형태의 균일한 Sn-Cu 범프를 형성하였다.

• 한국의류산업학회지
• /
• 제10권1호
• /
• pp.106-112
• /
• 2008

The purpose of this study is to define optimal conditions for wool blend fabric dyeing using Rhus verniciflua extract. K/S value, surface color change, the fastness to light, fastness to dry-cleaning, metal mordanting effects and antimicrobial activities were investigated. The results were summarized as follows; As the storage time of Rhus verniciflua stokes dyeing solution was longer, K/S was improved. K/S value showed the highest one when dyeing temperature and time were at 100oC and 60 minutes respectively. As for the changes of pH values of the dyeing solution, fabric was dyed well with the pH value of acid or neutral. K/S value recorded the highest at pH6 and the lowest at pH10. Fastness to light showed the unmordanted fabric is 2.84, and Fe is 1.69 on color difference. Antibacterial activities of Rhus verniciflua dyeing solution recorded high figures in both dyed fabric with unmordanted and dyed fabric with mordanting.

• 복식
• /
• 제27권
• /
• pp.121-132
• /
• 1996

This study showed the proper pigment extract in the Phe. Dyeing which is the basic dye of the natural plants dyeing,. Also it compared and examined the K/S the promotion of the color fastness and the effect of color difference change were attended by mordants and method of mordanting. 1. The most absorbance of Phellodendron. sol-ution is 330nm berberine is 430nm. 2. The best and proper temperature to extrat Phe,. was 80 and dyeing solution for 24 hours. 3. The pH effect was stable in the absorbances and color differences change. 4. Mordanted group increased the absorbances compared to non-mordanted sample. In case depth the most absorbance of Al. Sn. K. Cu and C. A solution were in 3% Fe and Cr were in 5%. In the color difference change they became dark reduced greenish and increased yellowish when their absorbances were in 3% 5. K./S was recoginzed by tainnin and fe, K/S was more increased pre-mordants than post-mordants. 6. Fe is the unchangable mordant in the color difference change and pre-mordants is more stable than post-mordants in the difference color. 7. Generally light C. F indicated more than grade 2 and light C. F, was much improved in post-mordanted by alumium potassium potass-ium dichromate. Washing C.F was improved in mordanted by tainnin and ferrous suulfate mordanted group was better than non-mordanted sample. Perspir-ation C,F was more stable in acid than alkali. Dry cleaning C.F indicated more than grade. 4.