• Proceedings of the KSME Conference
• /
• 2003.04a
• /
• pp.1936-1941
• /
• 2003

Characteristics of the high frequency and pulsatile flow investigated experimentally to understand the flow phenomena in the hydraulic system. In the study, I axis fatigue tester which are widely used for automobile filed are selected. 4 Pressure transducer, amplifier, A/D convertor are used to analyse and to obtain the pulsatle pressure waveform with high frequencies in hydraulic system. Matlab are used. to analyse the characteristics of frequency. Variation of pump input pressure and actuator acceleration frequency, pressure wave are measured with or without accumulators. For with accumulator, frequency amplitude of pressure are very lower than those of without accumulator due to absorbing function of accumulator. As the actuator acceleration frequency increased, effect of accumulator are very important to decrease the pulsatile pressure waveform with high frequencies.

• Elastomers and Composites
• /
• v.35 no.1
• /
• pp.4-11
• /
• 2000

A rubber diaphragm is a critical element of accumulators. The material of a diaphragm is nitrile rubber so as to recover and adjust the large deformation under external pressure fluctuation. The performance of accumulators is influenced by the deformation behaviors of the diaphragm. A large deformation behavior of the diaphragm has been investigated using the commercial finite element program MARC K7.1. The several elastic moduli have been used in linear analysis and Ogden's coefficients have been used in non-linear analysis. As a result, it has been shown that the deformation behavior with a elastic modulus of $0.3 kg/mm^2$ is similar to the behavior of non-linear analysis. And, the modified diaphragm shape to reduce the stress concentration has been proposed.

• Journal of Korea Society of Industrial Information Systems
• /
• v.4 no.2
• /
• pp.44-50
• /
• 1999

This paper presents a set of techniques to automatically find rate optimal or near rate optimal implementation of shift-invariant flow graphs on pipelined processor, in which pipeline processor has multiple accumulators and internal datapaths. In such case, the problem to be addressed is the scheduling of multiple instruction streams which control all of the pipeline stages. The goal of an automatic scheduler in this context is to rearrange the order of instructions such that they are executed with minimum iteration period between successive iteration of defining flow graphs. The scheduling algorithm described in this paper also focuses on the problem of removing the hazards due to inter-instruction dependencies.

• Journal of the Korean Society of Environmental Restoration Technology
• /
• v.8 no.5
• /
• pp.39-46
• /
• 2005

This study was conducted to investigate the heavy metal accumulation in wild plants. The samples from 5 plant species on 14 sites were taken on the roadside where urban and industrial regions in northern Gyeonggi do. Artemisia princeps var. orientalis, Chenopodium album L. var. centrobrum, Erigeron canadensis L., Rumex crispus L. and Taraxacum platycapum H. Dahlst were taken from different parts of the plants gathered in surveyed sites for analysing. This study classified which species were suitable to accumulators, excluders, or indicators which were provided as Phytoremediation for heavy metals(Cd, Cr, Ni, Pb and Zn) and considered the applicability of that work. 1. The mean accumulation of 6 heavy metals in plants was as follows; Zn> Cu> Cr> Pb> Ni> Cd in rows except for Ni and Pb in Erigeron. 2. The highest heavy metal accumulators were Taraxacum and Artemisia. 3. The comparison of heavy metal accumulations between the tops and roots in the plants was as follows; Zn> Cd> Pb> Ni> Cu> Cr. 4. Comparison of heavy metal accumulations between tops and roots, root parts were higher than the top parts in most of the plants. Especially, in Taraxacum, a ratio was over 1.0 in Cr, Ni, and Zn. Therefore, Taraxacum was an accumulator for 3 heavy metals. And Erigeron, Chenopodium, Rumex, Artemisia were good for excluders which had lower than 1.0.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1996.04a
• /
• pp.305-308
• /
• 1996

An analyzing method for pressure fluctuation in oil hydraulic pipe network was developed in this study. The object pipe network has multi-branch configuration, and the pipeline of it is composed of steel tubes, flexible hoses. Also, accumulators, orifices and lumped oil volume components are attached on it. Transfer matrix method, in other words impedance method, was used for the analysis. The reliablity and usefulness of the analyzing method was confirmed by comparing and investigating computed results and experimental results got in this study.

• Journal of Ocean Engineering and Technology
• /
• v.11 no.4
• /
• pp.152-158
• /
• 1997

An analyzing method for pressure fluctuations in oil hydraulic pipe network was developed in this study. The object pipe network has multi-branch configuration, and the pipelines of it are composed of steel tubes, flexible hoses. Also, accumulators, orifices and lumped oil volume components are attached on it. Transfer matrix method, in other words impedance method, was used for the analysis. The reliability and usefulness of the analyzing method were confirmed by investigation computed results and experimental results got in this study.

• Journal of the Korean Institute of Telematics and Electronics C
• /
• v.36C no.12
• /
• pp.27-35
• /
• 1999

In a typical spread spectrum system, parallel correlator occupies a large fraction of power consumption because of the large number of accumulators in the system. In this paper, a novel accumulator is proposed that can reduce the power consumption in the parallel correlator. The proposed accumulator counts the numbers of 1 of the incoming input data. The counted values are weighted and added together to obtain the final correlation value only at the end of the accumulation. The proposed accumulator has been designed and simulated by CADENCE Verilog-XL and synthesized by SYNOPSYS Design Compiler with $0.6{\mu}m$ standard cell library. Power consumption results have been obtained from EPIC PowerMill simulations. Simulation results are very encouraging. First, the power dissipation is reduced by 22% and the maximum operating frequency is increased by 323%. In addition, the parallel correlator using the proposed accumulators consumed less power than the conventional active parallel correlators by 22%, and less power than the conventional passive correlator by 43%.

• Transactions of The Korea Fluid Power Systems Society
• /
• v.3 no.3
• /
• pp.8-13
• /
• 2006

It is very important for the manufacturers to predict the life of hydraulic system components according to the results of life tests. Since it takes too much time to test the hydraulic system components until failure, the no-failure test method is applied for the life test of them. If the shape parameter of Weibull distribution, the number of samples, the confidence level, and the assurance life are given, the no-failure test times of hydraulic system components can be calculated by given equation. Here, the procedures to obtain the no-failure test times of the hydraulic system components such as hydraulic motors and pumps, hydraulic cylinders, hydraulic valves, hydraulic accumulators, hydraulic hoses, and hydraulic filters are described briefly.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1995.10a
• /
• pp.577-580
• /
• 1995

This paper suggests direct-acting hydraulic circuit to control clutches and brakes in automatic transmission. As only one pressure control valve controls the pressure of several friction elements with accumulators in conventional hydraulic circuit, the controllable range is limited. In addition, it is difficult to control the fine timing between apply clutch and release clutch. So, we designed new method to control the pressure of clutch which uses ressure control valve and pressure control solenoid valve independently in each friction element. through this structure improvement of hydraulic circuit, we can control the pressure of clutches and brakes finely and fine timing of between apply clutch and release clutch.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.11 no.5
• /
• pp.119-126
• /
• 2003

The simulator of a vehicle equipped with hydrostatic transmission and hydraulic accumulator type-braking energy regeneration system is developed using a PC. The simulator receives the accelerator pedal angle and the brake pedal angle generated by the operator using the keyboard, updates the state variables of the energy regeneration system responding to the input signals, and draws the moving pictures of the accumulator piston, pump plate angle and pump/motor plate angle every drawing time on the PC monitor. Also, the operator can observe the accel pedal angle, brake pedal angle, pressures of accumulators, vehicle speed, hydraulic torque, engine torque and air brake torque representing the operation of braking energy regeneration system through the PC monitor every drawing time. The simulator can be a very useful tool to design and improve the braking energy regeneration system.