• 복식
• /
• 제55권5호
• /
• pp.101-107
• /
• 2005

In this article, mordant absorption rate by the Change of temperature and fabric, discharge level by water washing, mordant density and method in mordant dye are going to be handled. Besides, how treatment method will have an effect on absorption rate and color, is also going to be covered. An atom extinction photometer was used to measure the amount of mordant absorbed in fabric at each temperature and mordant type. It turned out that absorption rate differs according to the type of mordant and sample or temperature. Also it turned out that the mordant input amount has little influence on absorption rate, that is to say, if though you use more mordants, just tiny amount of mordant is going to be absorbed in cloth. It is true that the higher temperature goes up, the better mordant absorption gets. It is found that the type of mordant and sample, treatment period affects the discharge rate. Normally $15{\~}98\%$ mordant comes off the fabric by water washing, to be specific, $17{\~}47\%$ Iron by water washing and it has better performance on cotton and nylon than silk, $1\%{\~}52\%$ Aluminum by water washing and better absorption on silk, $36{\~}89\%$ Chrome by water washing and better absorption on silk, $50{\~}89\%$ copper by water washing and better absorption on silk, poor on cotton. The examination of the K/S values and colors between before and after soaping has been conducted under the circumstance that the test fabrics had been treated at $80^{\circ}C$ for 30 minutes with $0.2\%$ soaping solution. In case of pre-mordanted fabrics, the K/S value nosedived after soaping, meanwhile densely mordanted fabric's K/S value soared but after soaping, it dropped sharply. It turned out that soaping treatment deteriorates absorption much more than water washing. It's considered that $0.1 \%$ (W/V) of mordant density is appropriate.

• Advances in aircraft and spacecraft science
• /
• 제5권4호
• /
• pp.499-513
• /
• 2018

One of the major problems in glass fiber reinforced epoxy (GFRE) composite pipes is the durability under water absorption. This condition is generally recognized to cause degradations in strength and mechanical properties. Therefore, there is a need for an intelligent system for detecting the absorption rate and computing the mass of water absorption (M%) as a function of absorption time (t). The present work represents a new non-destructive evaluation (NDE) technique for detecting the water absorption rate by evaluating the dielectric properties of glass fiber and epoxy resin composite pipes subjected to internal hydrostatic pressure at room temperature. The variation in the dielectric signatures is employed to design an electrical capacitance sensor (ECS) with high sensitivity to detect such defects. ECS consists of twelve electrodes mounted on the outer surface of the pipe. Radius-electrode ratio is defined as the ratio of inner and outer radius of pipe. A finite element (FE) simulation model is developed to measure the capacitance values and node potential distribution of ECS electrodes on the basis of water absorption rate in the pipe material as a function of absorption time. The arrangements for positioning12-electrode sensor parameters such as capacitance, capacitance change and change rate of capacitance are analyzed by ANSYS and MATLAB to plot the mass of water absorption curve against absorption time (t). An analytical model based on a Fickian diffusion model is conducted to predict the saturation level of water absorption ($M_S$) from the obtained mass of water absorption curve. The FE results are in excellent agreement with the analytical results and experimental results available in the literature, thus, validating the accuracy and reliability of the proposed expert system.

• 한국태양에너지학회 논문집
• /
• 제22권4호
• /
• pp.35-43
• /
• 2002

This research makes that quantitative radiation property of an actual town ward is obtained in quest of the parameter with regard to a radiation heat transfer property and set up several town ward models that reproduced a solid form of a city along the attribute of the city. A regular trend possibility that is able to evaluate a radiation characteristics of a town ward quantitatively from a town ward guideline and confirmation that is produced about each parameter as a result of a numerical value simulation it obtained. This research shot a coefficient of Gebhart's emission absorption. sky radiation absorption rate direct solar radiation absorption rate the parameter with regard to a radiation heat transfer characteristics of a town ward in each town ward model and a volume rate of a town ward advances case study under regular such condition and shot the absorption rate, direct and others days and calculated an absorption rate and checked about the relation between a town ward and each radiation heat transfer property of a city.

• 한국식품영양과학회지
• /
• 제28권3호
• /
• pp.705-709
• /
• 1999

To evaluate iron bioavailability in iron fortified milk, in vitro and in vivo method were used. Low molecular weight components(ILC) from milk was isolated and iron was added, then soluble iron from ILC iron complex was determined. Each iron sources and extrinsically labelled with FeCl3 was used for measuring absorption rate of iron from ILC radiolabelled iron complexes as radioiron absorption into the blood one hour after injection into ligated duodenal loops of iron deficient rats. Iron absorption rate was in the order of ferrous lactate(25.56%)$\geq$ferric citrate(24.71%)$\geq$ferrous sulfate(19.67%) when 100ppm iron was used. In separate experiments, iron fortified milks with each iron sources were gavaged into iron deficient rats. When 25ppm iron was added to milk, the order of iron absorption was ferrous sulfate(12.52%)>ferrous lactate(8.07%)>ferric citrate(6.52%) (p<0.05). When 100ppm iron was added to milk, absorption rate was decreased compared to the treatments with added 25ppm of iron. Absorption rate of ferrous sulfate(5.34%) from milk added 100ppm iron was highly lowered, but ferric citrate(6.45%) was not significantly changed. The absorption rate of ferrous lactate(5.82%) was 70% of 25ppm iron added milk.

• 설비공학논문집
• /
• 제11권3호
• /
• pp.332-338
• /
• 1999

An experimental study of absorption phenomena of water vapor into LiBr solution was carried out to find out the optimum solution flow rate. The staggered bundle of horizontal absorption tubes, which are the same configuration as the commercial heat pump, were tested. The results showed that the heat transfer and absorption rate were enhanced with the increase of LiBr solution flow rate. Those values for different absorber pressures showed the same qualitative trends. The optimum flow rate of solution was obtained as three times of the designed flow rate.

• Journal of Pharmaceutical Investigation
• /
• 제16권1호
• /
• pp.31-35
• /
• 1986

Effect of ethanol on the absorption rate, blood level and bioavailability of sulfamethazine (SM) in rats was determined. Absorption rate of SM was determined both by the in vitro and in situ experiment. In vitro, absorption rate of SM in rat small intestine was increased by 0.3, 1.0 and 3.0% ethanol. In situ, absorption rate of SM was increased by 0.3 and 1.0% ethanol but not by 3.0% ethanol. After oral administration, blood level of SM was elevated and relative bioavailability was significantly increased to 114.8% at the dose of 0.6g/kg ethanol but not significantly at the dose of 3.0g/kg ethanol. The time for attainment of peak blood level was changed from 2.5 to 1.5hr. Ethanol enhanced absorption rate constant of SM significantly and reduced elimination rate constant of SM administered orally at the dose of 0.6g/kg ethanol.

• 한국대기환경학회지
• /
• 제17권5호
• /
• pp.407-414
• /
• 2001

In this study, the absorption kinetics of $CO_2$onto a mixture of AMP (2-amino-2-methyl-1-propanol) MEA (monoethanolamine) water were investigated at 30 and 4$0^{\circ}C$ using a packed absorption tower. Solubility and absorption rate of $CO_2$into alkanolamine solutions and optimal condition of $CO_2$absorption process were investigated. The experimental conditions are as follows; temperature of 30 and 4$0^{\circ}C$, gas flow rate of 3ι/min for the absorption tower, and liquid flow rate of 0.1ι/min. Feed gas was a mixture of 85% $N_2$and 15% $CO_2$. The experimental results showed that AMP had greater solubilities and faster absorption rates than MEA and DEA. In addition, MEA had the fastest initial reaction rate. To improve the properties of AMP which have low initial reaction rate and high cost, AMP was used with MEA. The mixing ratio was also changed in constant total molarity of 1,2,3 and 4. The experimental results can be summarized as follows: (1) in solubility experiment, the addition of MEA in constant total polarity decreased the solubility of $CO_2$in AMP/MEA mixture. (2) from 0 to about 0.3 in mixing ratio, the solubility of $CO_2$in AMP/MEA mixture had little differences compared with the sum of solubility of AMP only and solubility of MEA only . (3) mixing ratio of 0.3 was found to be an optimal point with the fastest $CO_2$absorption rate.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2017년도 춘계 학술논문 발표대회
• /
• pp.182-183
• /
• 2017

This research identifies radon gas absorption mechanism by adsorption materials, replacing gypsum board with radon emissions, the density and absorption rates of magnesium were carried out using vermiculite, anthracite, powdered active carbon, bentonite, illite, diatomite as a basic study on the fire resistance type of radon Gas reduction type with absorption and decomposition. As a result of the experiment, diatomite showed the lowest density, and the highestt value was the highest. For the absorption rate, bentonite showed the highest absorption rate, and the anthracite showed the lowest absorption rate.

• 펄프종이기술
• /
• 제47권1호
• /
• pp.75-83
• /
• 2015

The applicability of oil palm biomass, EFB(Empty Fruit Bunch) as raw materials for environmental friendly packaging material, pulp mold, was evaluated in this study. The changes in the water absorption properties of pulp mold by the addition of EFB and the surface treatments with PVA and AKD were analyzed by measuring the changes in the water absorption rate and the water contact angle. The each pulp mold sample was prepared by using laboratory wet pulp molder. And the water absorption rate of each samples were evaluated by measuring times for the absorption of a 0.1 ml water drop on the pulp mold sample surface. The addition of EFB to the pulp mold made of OCC resulted in the decrease of water absorption rate and the increase in the water contact angle. The surface treatments with PVA and AKD on the OCC pulp mold showed the significant reduction in the water absorption rate. However, in case of ONP pulp mold, the addition of EFB and the surface treatments with PVA and AKD showed no big changes in water absorption times. Those might be come from the finer surface structure of ONP pulp mold which were made of more finer and flexible fibers and more hydrophilic fibers. The results of this study showed the functional properties such as water absorption rate, could be controlled by the application of EFB and the treatments with AKD or PVA, especially in case of the OCC pulp mold.

• 한국산학기술학회논문지
• /
• 제22권4호
• /
• pp.131-139
• /
• 2021

이 논문은 흡수율이 높은 제올라이트를 일반 굵은골재의 대체재로 보도용 조경포장 콘크리트에 적용하기 위한 기초 연구로서, 제올라이트 굵은골재 대체율에 따른 포장 콘크리트의 흡수성능과 강도 특성을 파악하였다. 제올라이트 굵은골재의 흡수율은 약 14%로서 일반 굵은골재와 비교하여 흡수성능이 2.5배 증가하였다. 그리고, 제올라이트 굵은골재를 포장 콘크리트에 혼입하면 굵은골재 대체율에 따라 흡수율이 증가하고, 최대 대체율 50%에서 5.2%로 일반 포장 콘크리트와 비교하여 약 42% 증가하였다. 제올라이트 혼입 포장 콘크리트의 압축강도는 대체율 20%까지 증가한 후 감소하였지만 건설기준코드에서 규정하는 압축강도 기준은 모두 충족하였다. 휨강도는 대체율 10%까지 기준강도를 만족하였으나 대체율에 따라 강도가 감소하였으며, 포장 콘크리트의 균열저항성에 영향을 주는 쪼갬인장강도는 대체율 20%까지 일반 포장 콘크리트의 강도보다 크게 나타났다. 제올라이트 혼입 포장 콘크리트의 흡수성능과 강도 특성에 대한 연구결과로부터 제올라이트 굵은골재를 일반 굵은골재의 대체재로 적용이 가능함을 확인하였다.