• 한국정밀공학회지
• /
• 제33권12호
• /
• pp.1007-1013
• /
• 2016

This paper presents the development of a magneto-optical encoder for higher precision and smaller size. In general, optical encoders can have very high precision based on the position information of the slate, while their sizes tend to be larger due to the presence of complex and large components, such as an optical module. In contrast, magnetic encoders have exactly the opposite characteristics, i.e., small size and low precision. In order to achieve encoder features encompassing the advantages of both optical and magnetic encoders, i.e., high precision and small size, we designed a magneto-optical encoder and developed a method to detect absolute position, by compensating for the error of the hall sensor using the linear table compensation method. The performance of the magneto-optical encoder was evaluated through an experimental testbed.

• Journal of Power Electronics
• /
• 제9권5호
• /
• pp.748-756
• /
• 2009

This paper presents a compensation algorithm for position error due to an amplitude imbalance between resolver output signals. Resolvers are typically used to obtain absolute position information for motor drive systems in severe environments. Position error is caused by an amplitude imbalance of the resolver output signals. As a result, the d- and q-axis currents of synchronous reference frame have periodic ripples in the stator fundamental frequency in permanent magnet synchronous motor (PMSM) drive systems. Therefore, this paper proposes a compensation algorithm to reduce the position error generated by the amplitude imbalance. The proposed method does not require any additional hardware, and reduces computation time with a simple integral operation according to rotor position. In addition, the position error can be directly compensated for by the estimated position error. The effectiveness of the proposed compensation algorithm is verified through several simulations and experiments.

• 제어로봇시스템학회논문지
• /
• 제13권10호
• /
• pp.970-977
• /
• 2007

Absolute position detector which is one of the major equipment in the field of factory automation, not only perceives the absolute position of the rotary machine but also outputs switch data according to the given angle. Absolute position detector is composed of sensor module and its controller. In this paper, a sensor driver is implemented using FPGA with VHDL. This chip has a less form factor than conventional circuit. A test shows reliable precision within THD(total harmonic distortion) of 0.2% which can be applicable commercially. Also, FPGA-based phase error compensation methods were newly discussed. In the future, more research will be conducted to enhance the precision by the introduction of 3-phase transformer.

• 제어로봇시스템학회논문지
• /
• 제16권10호
• /
• pp.975-981
• /
• 2010

Existing error compensation method of industrial electronic absolute displacement detector only depends on skilled engineers. This paper proposes a new table method in order to automatize error compensation. An waveform changes according to the parallel resistance for each pole were tabularized and four waveforms were superimposed to minimize total phase error. These process was verified using simulink. As a result of applying proposed method to the real sensor, peak to peak error was reduced from $3.428^{\circ}$ to $0.879^{\circ}$. In this case, compensation resistance is $4.7k\Omega$ in B pole and $20k\Omega$ in C pole. This compensation rate is comparable to skilled engineers, and it takes 0.8 second which is far shorter than 15 minutes when expert does.

• 대한전자공학회논문지SP
• /
• 제39권3호
• /
• pp.49-57
• /
• 2002

본 논문에서는 TMS320C80 MVP(multimedia video processor)를 이용하여 영상 항법변수 추출 알고리듬을 실시간 구현하는 방법에 대해 연구하였다. 영상 항법변수 추출 알고리듬은 상대위치 추정과 절대위치 보정으로 이루어져 있으며, 절대위치 보정은 고해상도 항공영상과 IRS(Indian remote sensing) 위성영상 그리고 DEM(digital elevation model)을 이용한 방법이 있다. 이러한 알고리듬들을 수행하는 통합시스템을 MVP가 탑재된 DSP 보드로 실시간 구현하였다. 이를 위해 영상을 분할하여 병렬처리 함으로써 처리 시간을 줄였다. 모의 실험을 통해 실시간 처리가 가능함을 알 수 있었고, 추정오차 측면에서 성능을 평가하였다.

• Journal of Electrical Engineering and Technology
• /
• 제11권4호
• /
• pp.889-897
• /
• 2016

This paper presents an improved approach for compensating rotor position signal displacement in brushless DC (BLDC) motors with misaligned hall-effect sensors. Typically, the hall-effect sensors in BLDC motors are located in each phase and positioned exactly 120 electrical degrees apart. However, limitations in mechanical tolerances make it difficult to place hall-effect sensors at the correct location. In this paper, a position error compensator to counteract the hall-effect sensor positioning error is proposed. The proposed position error compensator uses least squares error analysis to adjust the relative position error and back-EMF information to reduce the absolute offset error. The effectiveness of the proposed approach is verified through several experiments.

• 한국지능시스템학회논문지
• /
• 제8권5호
• /
• pp.39-44
• /
• 1998

이동 로봇의 운행을 위해서 이동 로봇의 절대 위치를 결정하는 것이 중요하다. 본 논문에서는 신경회로망을 이용하여 랜드마크의 영상을 통해 이동 로봇의 위치를 결정하는 방법을 제안한다. 픽셀의 불확시한 값, 부정확한 카메라 조정과 렌즈의 왜곡으로 인해 이동 로봇의 위치를 결정에 있어서 위치 오차가 생기게 된다. 이러한 오차를 줄이기 위해서 BPNN(Back Propagation Neural Network)를 사용하는 방법을 제안한다. 기존의 방법과 비교하여 우수성을 보여주기 위해서 실험결과를 보여준다.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1997년도 한국자동제어학술회의논문집; 한국전력공사 서울연수원; 17-18 Oct. 1997
• /
• pp.532-535
• /
• 1997

This paper describes the design of a fuzzy-logic controller for a differential-drive mobile robots. This controller uses absolute position information to modify control parameters to compensate the orientation error. CC-Control method is compensated for the internal error by wheel encoders and the fuzzy-logic control provides compensation for external errors. The validities of the proposed scheme is evaluated using simulation.

• 한국정밀공학회지
• /
• 제18권4호
• /
• pp.190-196
• /
• 2001

The naval vessel must moves rolling, pitching, yawing by wave when it runs in ocean. Some narrow beam antenna needed position compensation by stabilizer or gimbal for best performance. This paper presents the precision position control for heavy weight(130kg) in roll and pitch direction. Generally it's called for gimbal. This gimbal uses P-I controller, and it's driven by linear actuator and servo motor. This gimbal gets ship's gyro signal and synchro, which have the absolute angle value. Some other similar equipments are driven by huge hydraulic power, but this gimbal is driven by small servo motor. This control loop gets the following procedure repeatedly; reading ship gyro and gimbal synchro, calculating compensated error and control output, driving motor and actuator The performance of gimbal system was satisfied.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2006년 학술대회 논문집 정보 및 제어부문
• /
• pp.560-562
• /
• 2006

In this paper, Correct problem in dead reckoning system and proposed about position error revision techniques of mobile robot to use RFID tag for position awareness. With the dead reckoning system, as the accumulation of error are unavoidable because of accumulation of informations as the time passage, so it is impossible to get correct information about posture, including torrent direction, movement distance, etc. As one of compensation method, the suggested method is that after selecting special area (corridor), compensate absolute location information by arranging two line of RFID tag along two side of corridor. Through this suggested method, it could be used when robot wants to move in limited areas.