• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2002년도 춘계학술대회 논문집
• /
• pp.585-590
• /
• 2002

Abrasive water-jet(AWJ) machining is a new cutting technology. The AWJ can cut various materials touch as metal, glass and stone. However, the AWJ machining makes troubles including kerf, rounding and side taper. In this study, we investigated the correlation between parameters of abrasive water-jet machining arid cutting characteristics. The machining parameter were the material thickness and the traverse speed. The experiment was conducted to cut the stainless steel(STS41) and the mild steel(SS41) specimens. The results of the experiment weirs presented as the relation between cutting conditions and trouble of a dimension error, a conner error, an uncut width and a kerf.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2002년도 춘계학술대회 논문집
• /
• pp.984-987
• /
• 2002

Abrasive water-jet(AWJ) machining is a new cutting technology. The AWJ can cut various materials such as metal, glass and stone. However, the AWJ machining makes troubles including kerf, rounding and side taper. In this study, we investigated the correlation between parameters of abrasive water-jet machining and cutting characteristics. The machining parameters were the material thickness and the traverse speed. The experiment was conducted to cut the stainless steel(STS41) and the mild steel(SS41) specimens. The results of the experiment were presented as the relation between cutting conditions and troubles of a dimension error, a conner error, an uncut width and a kerf.

• 한국생산제조학회지
• /
• 제25권1호
• /
• pp.83-88
• /
• 2016

Because of the increasing tool cost for cutting hard-to-cut materials, abrasive water jet (AWJ) milling recently has been regarded as a potential alternative machining method. However, it is difficult to control the depth and width of cut in AWJ milling because they vary depending on many AWJ cutting parameters. On 27 conditions within a limited range of pressure, feed rate, and abrasive flow rate, AWJ cutting was conducted on titanium, and depth profiles were measured with a laser sensor. From the depth profile data, depth and width of cut were acquired at each condition. The relationships between depth and parameters and between width and parameters were derived through regression analysis. The former can provide proper cutting conditions and the latter the proper pick feed necessary to generate a milled surface. It is verified that pressure mostly affects depth, whereas abrasive flow rate mostly affects width.

• 터널과지하공간
• /
• 제6권2호
• /
• pp.175-183
• /
• 1996

Linear cutting tests on granite were conducted to evaluated the cutting performance of abrasive water jet(AWJ) using several types of abrasives. The abrasives used in the tests were grarnet, alumimum oxide, and silicon carbide. And one type of granite which is comercially known as "KeuchangSuk" was used as workpiece throughout the tests. The results from the tests were described in terms of cutting depth and abrasive productivity. Authors tried to confirm the effects of the operational parameters of abrasive mass flow rate, water pressure, and traverse speed of nozzle on cutting depth and presented almost all the data obtained in the tests. Abrasive productivity can be defined as the area of kerf wall cut by unit weight of abrasive and is an important factor to evaluated the cutting ability of abrasive and assess the cost effectiveness of an AWJ system. In the tests the maximum abrasive productivities of garnet, alumina, and silicon carbide were about 0.21, 0.24, and 0.20 $\textrm{cm}^2$ respectively under similar operational conditions.onditions.

• 한국공작기계학회논문집
• /
• 제13권3호
• /
• pp.1-7
• /
• 2004

Abrasive water-jet(AWJ) machining can cut various materials such as metal, glass and plastics. However, the AWJ machining has some troubles including kerf, rounding and side taper. In this study, we experimently investigated the correlation between the traverse speed of the abrasive water-jet and the dimensional error of the workpiece according to the thickness and the types of the material. The specimen was the stainless steel and the mild steel and the predetermined contour cutting was conducted. A comer radius error, an uncut width and a kerf were measured and evaluated.

• 한국생산제조학회지
• /
• 제25권2호
• /
• pp.118-123
• /
• 2016

Overlap cutting is a fundamental method of applying abrasive water jet (AWJ) machining to milling to produce a wider surface because the nozzle outlet is approximately 1.0 mm wide. In this study, the effects of overlap cutting on the depth profile and surface roughness are investigated. The overlapping area depends on the amount of step over, which is controlled in the pick-feed direction. If the step over is equal to or larger than the diameter of the nozzle, no overlap cut occurs but large cusps remain between the cut paths. A step over as small as one-thirds of the nozzle diameter may lead to triple-overlap cutting resulting in an extraordinary depth. By using pocket milling experiments with a step over of 0.46 (or 0.47), it is verified that AWJ can produce a milled surface of titanium, one of the hard-to-cut materials, with $76{\mu}m$ Ra.

• 한국정밀공학회지
• /
• 제15권6호
• /
• pp.48-57
• /
• 1998

Abrasive waterjet(AWJ)은 가공시 열에 의한 가공경화가 없기 때문에 유리, 세라믹, 타이타늄및 금속복합재료와 같은 난삭재의 가공기술로 사용이 증가되었다. Acoustic emission(AE)신호에 의한 AWJ 세라믹 drilling가공시 On-Line Monitoring의 가능성이 고찰되었다. 기계 적인 물성이 서로 상이한 3종류의 세라믹이 본 연구에서 사용되었으며, AE신호는 AWJ drilling의 깊이를 monitoring하는데 유용함을 알 수 있었고 또한 세라믹의 material removal mechanisms을 규명하였다.

• 한국세라믹학회지
• /
• 제47권3호
• /
• pp.232-236
• /
• 2010

In recent years abrasive water jet (AWJ) has received significant attention as a technology used in the manufacturing industry for cutting materials. In this paper we report the development of a new preparation method of abrasives for water jet by using an air bubbling sedimentation rate control technique. The SiC abrasives prepared by an air bubbling sedimentation rate control technique using latex resin are found to be superior to the conventional abrasives not only in surface roughness uniformity but also in lifetime. The AWJ test results also show that the former has also better impact-resistance and wear-resistance than the latter.

• 한국산업융합학회 논문집
• /
• 제23권5호
• /
• pp.817-823
• /
• 2020

In recent, the machining of difficult-to-cut materials such as titanium alloys, stainless steel, Inconel, ceramic, glass, and carbon fiber reinforced plastics (CFRP) used in aerospace, automobile, medical industry is actively researched. Abrasive waterjet is a non-traditional processing method in which ultra-high pressure water and abrasive particles are mixed in a mixing chamber and shoot out jet through a nozzle, and removed by erosion due to collision with a material. In particular, the nozzle of the abrasive waterjet is one of the most important parts that affect the machining quality as with a cutting tool in general machining. It is very important to monitor the condition of the nozzle because the workpiece is uncut or the surface quality deteriorates due to wear, expanding of the bore, damage of the nozzle and clogging of the abrasive, etc. Therefore, in this paper, we propose a monitoring system based on Acoustic Emission(AE) sensor that can detect nozzle condition in real time during AWJ processing.