• Journal of Welding and Joining
• /
• v.31 no.6
• /
• pp.27-31
• /
• 2013

Magnesium alloy is used on parts of aircraft and electronic equipment because of the highest specific strength among the common metal materials. Recently, studies about appling magnesium alloy sheet to automotive bodies are on the increase rapidly. For application to automotive bodies, researches about characteristics of resistance spot welding of magnesium alloy sheet are essential. Magnesium alloy has low boiling point, so getting sound bead shape is difficult when appling varies welding processes. Resistance spot welding is also particular about setting optimum welding conditions because of spatter generation, pores and cracks occurrence in nugget. And life of electrodes is very short because of alloying with copper that main material of electrodes. This requires frequent dressing and replacement of electrodes and decrease in productivity of resistance spot welding on magnesium alloy. Therefore in this study, for effective analysis of changes in tensile shear load and nugget size during electrode life test, evaluate detail characteristics of resistance spot welding on magnesium alloy sheet using dome type electrode.

• Journal of Welding and Joining
• /
• v.31 no.4
• /
• pp.7-12
• /
• 2013

The dissimilar welding between magnesium alloy and steel sheet was required in automobile industry to increase the strength of the dissimilar joints. Laser brazing is one of the good joining processes for Mgsteel dissimilar joint. In this study, the effect of coating materials was evaluated on the laser brazing for the dissimilar joint between AZ31 and coated steels such as Zn, Sn and Ni. Diode direct laser was used to braze the lap-edge joint with Mg600 filler wire and Superior #21 flux. The wettability was best on Zn coated steel. The interlayer was formed at the interface between brazement and steel for all coating materials. The strengths of brazed specimen were 146.5N/mm, 204.6N/mm and 101.6N/mm for Zn, Sn and Ni coated steel respectively.

• Journal of Korea Foundry Society
• /
• v.32 no.3
• /
• pp.150-156
• /
• 2012

발포금속은 초경량 재료로서 폐기공과 개기공의 두 가지 형태의 구조를 지니고 있으며 폐기공은 내충격성, 흡음성, 단열성의 기능을 지니고 있고, 개기공은 필터, 생체지지대, 촉매재, 열방출재 등으로 사용되고 있다. 개기공발포재는 삼차원 구조모양으로 프리커서를 이용한 압력정밀주조나 기공입자용출법으로 제조하고 있으나 기공의 크기나 셀의 형상, 두께 등을 조절하기에 어려움이 있다. 이를 해결하기 위하여 환경친화적인 펄라이트를 사용하여 목적하는 크기의 그래뉼을 제조한 후, 용융마그네슘합금을 감압주조법으로 주조하여 그래뉼의 크기로 기공율을 조절하고, 주형의 온도와 압력에 따른 유동의 길이를 측정하였다. 그래뉼 직경이 2.3 $mm{\O}$ 일때에 주형의 온도 $300^{\circ}C$ 이상, 압력이 5000 Pa 이상에서 유동길이 6.5 cm 이상을 얻었다.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2004.05a
• /
• pp.186-189
• /
• 2004

Although magnesium has high potential for structural material due to the lightweight and high specific strength, the structural application has been limited by the low ductility at room temperature. The reason of the poor ductility is few activated slip systems of magnesium (HCP structure) during deformation. As temperature increases, however, additional non-basal slip systems are incorporated to exhibit higher ductility comparable to aluminum. In the present study, a series of tensile tests of Mg-Al alloy has been carried out to study deformation behavior with temperature variation. Analysis of load relaxation test results based on internal variable approach gave information about relationship between the micromechanical character and corresponding deformation behavior of magnesium. Especially, the material parameter, p representing dislocation permeability through barriers was altered from 0.1 to 0.15 as the non-basal slip systems were activated at high temperature.

• Transactions of Materials Processing
• /
• v.18 no.4
• /
• pp.347-353
• /
• 2009

The apparent activation energy, the applied stress exponent, and rupture life have been measured from creep experiments over the range of $200^{\circ}C$ to $220^{\circ}C$ and the applied stress range of 64MPa to 94MPa. The materials were used AZ31 magnesium alloys treated by plasma electrolytic oxidation of $20{\mu}m$ and $40{\mu}m$ at surface to investigate the its influence on creep behavior, and creep tests were carried out under constant applied stress and temperature. The experimental results showed that the dipper the thickness of surface treatment the higher the activation energy and stress exponent. And the higher temperature and applied stress, the lower stress exponent and activation energy, respectively. Also the dipper the thickness of surface treatment the longer creep rupture time.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.11 no.2
• /
• pp.34-39
• /
• 2012

In this study, the friction welding experiment was performed by using the design of experiment. And the signal data acquired by acoustic emission sensor were analyzed to predict the tensile strength of friction welding part at friction welding process for AZ31 magnesium alloy. A dimensionless coefficient($\phi_{AE}$), which consisted in the square of AE rms and variance, was defined as the characteristic of friction welding and the prediction equation was obtained by using linear regression. As the result of analysis, it was seen that the correlation between predicted and measured values became very close and on-line prediction of the ensile strength was possible in friction welding part.

• Transactions of Materials Processing
• /
• v.17 no.2
• /
• pp.97-101
• /
• 2008

Unique constitutive behavior of magnesium alloys as one of hexagonal close packed(hcp) metals has been implemented into the commercial finite element program ABAQUS. The constitutive equations can represent asymmetry in tension-compression yield stresses and flow curves. For the verification purpose, the springback of AZ31B magnesium alloy sheet was measured using the unconstrained cylindrical bending test proposed in Numisheet'2002 benchmark committee. Besides the developed constitutive models, the isotropic models based on tensile and compressive properties were also considered for comparison purpose. The predicted results by the finite element analysis and corresponding experiments showed enhanced prediction capability in springback analysis.

• Proceedings of the KWS Conference
• /
• 2005.11a
• /
• pp.183-185
• /
• 2005

In an attempt to optimize friction spot joining process of Mg alloys, effects of joining parameters such as rotating speed, plunging depth, and dwelling time on the joints properties were evaluated. Experimental tests were carried out for lap joined AZ31B-H24 sheets. A wide range of joining conditions could be applied to join Mg alloys without defects in the weld zone except for certain welding conditions with an insufficient heat input. The microstructures and hardness variations in the weld regions are discussed. For sound joints without defects, tensile shear strength of weld joints was higher approximately 116% than typical tensile shear strength of electrical resistance spot-welded joints for magnesium(Welding handbook, Vol 3, AWS).

• Transactions of Materials Processing
• /
• v.13 no.6 s.70
• /
• pp.535-539
• /
• 2004

Although magnesium has high potential for structural material due to the lightweight and high specific strength, the structural application has been limited by the low ductility at room temperature. The reason of the poor ductility is few activated slip systems of magnesium (HCP structure) during deformation. As temperature increases, however, additional non-basal slip systems are incorporated to exhibit higher ductility comparable to aluminum. In the present study, a series of tensile tests of Mg-Al alloy has been carried out to study deformation behavior with temperature variation. Analysis of load relaxation test results based on internal variable approach gave information about relationship between the micromechanical character and corresponding deformation behavior of magnesium. Especially, the material parameter, p representing dislocation permeability through barriers was altered from 0.1 to 0.15 as the non-basal slip systems were activated at high temperature.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.12
• /
• pp.513-518
• /
• 2019

Friction Stir Welding is a welding technique for metal materials that utilizes the heat generated by friction between the material to be welded and the welding tool that rotates at high speed. In this study, a numerical analysis method was used to analyze the change in the internal temperature of the welded material during friction stir welding. As the welding target material, AZ31 magnesium alloy was applied and the welding phenomenon was considered a flow characteristic, in which a melting-pool was formed. FLUENT was used as the numerical tool to perform the flow analysis. For flow analysis of the welding process, the welding material was assumed to be a high viscosity Newtonian fluid, and the boundary condition of the welding tool and the material was considered to be the condition that friction and slippage occur simultaneously. Analyses were carried out for various rotational speeds and the translational moving speed of the welding tool as variables. The analysis results showed that the higher the rotational speed of the welding tool and the slower the welding tool movement speed, the higher the maximum temperature in the material increases. Moreover, the difference in the rotational speed of the welding tool has a greater effect on the temperature change.