• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.8 no.2
• /
• pp.232-239
• /
• 2007

There is an increasing concern to interconnect DG(Distributed Generation) units into a distribution system and operate and maintain the system power quality within a proper level to distribution companies, regional electricity utilities and industrial customers. Recently, this situation makes many experts estimate a next generation of distribution system which is composed of some micro-grids. But the proposed micro-grid is only mentioned as a small grid with some DG units, some power quality compensators, communication and control equipments. In this paper, a topology and an operation/control algorithm of the micro-grid which is able to supply the electricity with high reliability and quality, are proposed.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.25 no.2
• /
• pp.133-141
• /
• 2020

The use of high-gain-voltage step-up converters for distributed power generation systems is being popularized because of the need for new energy generation and power conversion technologies. In this study, a new constructed high-gain-boost DC-DC converter was proposed to coordinate low voltage output DC sources, such as PV or fuel cell systems, with high DC bus (380 V) lines. Compared with traditional boost DC-DC converters, the proposed converter can create higher gain and has wider input voltage range and lower voltage stress for power semiconductors and passive elements. Moreover, the proposed topology produces multilevel DC voltage output, which is the main advantage of the proposed topology. Steady-state analysis in continuous conduction mode of the proposed converter is discussed in detail. The practicability of the proposed DC-DC converter is presented by experimental results with a 300 W prototype converter.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.5 no.1
• /
• pp.157-176
• /
• 2011

An interest-based P2P constructs the peer connections based on similarities for efficient search of resources. A clustering technique using peer similarities as data is an effective approach to group the most relevant peers. However, the separation of groups produced from clustering lowers the scalability of a P2P network. Moreover, the interest-based approach is only concerned with user-level grouping where topology-awareness on the physical network is not considered. This paper proposes an efficient scalable search for the interest-based P2P system. A scalable multi-ring (SMR) based on fuzzy clustering handles the grouping of relevant peers and the proposed scalable search utilizes the SMR for scalability of peer queries. In forming the multi-ring, a minimized route function is used to determine the shortest route to connect peers on the physical network. Performance evaluation showed that the SMR acquired an accurate peer grouping and improved the connectivity rate of the P2P network. Also, the proposed scalable search was efficient in finding more replicated files throughout the peer network compared to other traditional P2P approaches.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.25 no.6
• /
• pp.549-558
• /
• 2012

A topology optimization method for phononic crystals is developed for the design of sound barriers, using the level set approach. Given a frequency and an incident wave to the phononic crystals, an optimal shape of periodic inclusions is found by minimizing the norm of transmittance. In a sound field including scattering bodies, an acoustic wave can be refracted on the obstacle boundaries, which enables to control acoustic performance by taking the shape of inclusions as the design variables. In this research, we consider a layered structure which is composed of inclusions arranged periodically in horizontal direction while finite inclusions are distributed in vertical direction. Due to the periodicity of inclusions, a unit cell can be considered to analyze the wave propagation together with proper boundary conditions which are imposed on the left and right edges of the unit cell using the Bloch theorem. The boundary conditions for the lower and the upper boundaries of unit cell are described by impedance matrices, which represent the transmission of waves between the layered structure and the semi-infinite external media. A level set method is employed to describe the topology and the shape of inclusions. In the level set method, the initial domain is kept fixed and its boundary is represented by an implicit moving boundary embedded in the level set function, which facilitates to handle complicated topological shape changes. Through several numerical examples, the applicability of the proposed method is demonstrated.

• Journal of Korean Home Economics Education Association
• /
• v.6 no.2
• /
• pp.133-145
• /
• 1994

The purposes of this study are to investigate the relationship between the Piaget’s cognitive developmental theory and the practical course subject in elementary school which have the characteristics of skillful subject and living subject, and to discriminate the suitability of contents of the practical course subject for the childrens’level of cognitive development. This work could serve the theoretical background that the practical course subject presents practical experiences which lead the development of logicomathematical thinking abilities. The results of the content analysis shows that create activities develop the logicomathematical thinking abilities such as projective geometry, topology geometry, area conservation, length & distance conservation, and volume & mass conservation. And the most contents of the practical course subject are suitable for the childrens’level of cognitive development.

• Proceedings of the KIPE Conference
• /
• 2017.07a
• /
• pp.7-11
• /
• 2017

This paper describes a design concept of NPC1 power stack for 1500VDC megawatt level solar inverter. This stack uses three latest half-bridge IGBT modules with highest power density and operation junction temperature, which enable realization of power level beyond 1MW without paralleling. Critical design concept on loop inductance is explained. Dynamic characteristics are verified by double-pulse test. Thermal characteristics and output power limits are verified by thermal test. Temperature-sensitive component on PCB as output power constraint is identified. Different PCB repositioning solutions are tested to give the overall output power thermal derating curves, which enable output power of 1.15MW at $T_A=55^{\circ}C$ with $15^{\circ}C$ thermal margin. The power stack characteristic and performance change under different thermal environment is further analyzed.

• The KIPS Transactions:PartC
• /
• v.14C no.4
• /
• pp.365-370
• /
• 2007

Connected Dominating Set(CDS) has been used as a virtual backbone in wireless ad hoc networks by numerous routing and broadcast protocols. Although computing minimum CDS is known to be NP-hard, many protocols have been proposed to construct a sub-optimal CDS. However, these protocols are either too complicated, needing non- local information, not adaptive to topology changes, or fail to consider the difference of energy consumption for nodes in and outside of the CDS. In this paper, we present two Timer-based Energy-aware Connected Dominating Set Protocols(TECDS). The energy level at each node is taken into consideration when constructing the CDS. Our protocols are able to maintain and adjust the CDS when network topology is changed. The simulation results have shown that our protocols effectively construct energy-aware CDS with very competitive size and prolong the network operation under different level of nodal mobility.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.16 no.4
• /
• pp.451-462
• /
• 2016

Photovoltaic energy conversion becomes main focus of many researches due to its promising potential as source for future electricity and has many advantages than the other alternative energy sources like wind, solar, ocean, biomass, geothermal etc. In Photovoltaic power generation multilevel inverters play a vital role in power conversion. The three different topologies, diode-clamped (neutral-point clamped) inverter, capacitor-clamped (flying capacitor) inverter and cascaded h-bridge multilevel inverter are widely used in these multilevel inverters. Among the three topologies, cascaded h-bridge multilevel inverter is more suitable for photovoltaic applications since each pv array can act as a separate dc source for each h-bridge module. This paper presents a single phase Cascaded H-bridge five level inverter for grid-connected photovoltaic application using sinusoidal pulse width modulation technique. This inverter output voltage waveform reduces the harmonics in the generated current and the filtering effort at the input. The control strategy allows the independent control of each dc-link voltages and tracks the maximum power point of PV strings. This topology can inject to the grid sinusoidal input currents with unity power factor and achieves low harmonic distortion. A PID control algorithm is implemented in Arm Processor LPC2148. The validity of the proposed inverter is verified through simulation and is implemented in a single phase 100W prototype. The results of hardware are compared with simulation results. The proposed system offers improved performance over conventional three level inverter in terms of THD.

• Proceedings of the KIPE Conference
• /
• 2012.07a
• /
• pp.399-400
• /
• 2012

The proposed battery charger presented in this paper is suitable for Lead-Acid Battery and the dc/dc buck converter topology is applied as a charger circuit. The technique adopted in this charger is constant current & constant voltage dual mode, which is decided by the value of voltage of proposed battery. Automatic mode change function is detected by the percentage value of level of battery charging. CC Mode (Constant Current Mode) is operated when charging level is below 80% of the total charging of Battery voltage and above 80% of battery voltage charging, CV Mode (Constant Voltage Mode) is automatically operated. As the charging level exceeds 120%, it automatically terminates charging. The feedback signal to the PWM generator for charging the battery is controlled by using the current and voltage measurement circuits simultaneously. This technique will degrade the damage of proposed type of battery and improve the power efficiency of charger. Finally, a prototype charger circuit designed for a 12-V 7-Ah lead acid battery is constructed and tested to confirm the theoretical predictions. Satisfactory performance is obtained from simulation and the experimental results.

• Proceedings of the Korean Institute of Interior Design Conference
• /
• 2005.10a
• /
• pp.183-186
• /
• 2005

The purpose of this study is to actualize the planning method of the Mixed-use Housing. Enter in 2000 years, contruction of Mixed-use Housing is rapidly increasing with acrovill and tower palace as its starting point. Mixed-use Housing is topology that mix function of residential and business and commercial facilities by kind of mixed-use development. And, Mixed-use Housing which is located in busy urban commercial strict should meet the demand not only as functional city. And it is a type of urban housing that located in busy urban commercial district demands function of residential. As for locational situation and types of public space researched and analyzed in this thesis, those space were left alone with short analyzation on main consumers level as well as short recognition of public space for all of the six combined facilities of dewelling and commercing