• Journal of Astronomy and Space Sciences
• /
• 제20권3호
• /
• pp.205-216
• /
• 2003

회전안정화 로켓 모터를 이용하는 upper stage 위성체의 자세 불안정 현상을 연구하였다. 이 위성체는 대칭형의 본체와 내장된 유동질량으로 구성되며, 유동질량은 구진자로 모델링되었다. 종래의 선형모델이 갖는 단점을 보완하기 위해 정확한 시변 비선형 방정식을 사용하고, 본체 및 구진자 모두 회전 대칭축에 대해 정상상태에 있다고 가정하였다. 본 논문에서는 진자에 대한 준정상해(quasi-stationary solution) 및 공진조건을 파라미터의 함수로 결정하였다. 공진조건의 분석결과 유동질량은 계수자극 및 외부자극을 동시에 받으며, 자극을 받은 유동질량으로부터 에너지가 본체에 유입되면서 위성체는 불안정한 장동운동을 일으키는 것으로 확인되었다. 본 논문에서는 수치시뮬레이션 예시를 통하여 주어진 위성체 모델에 대해 발생가능한 공진조건에서 진자의 운동, 위성체 각 운동량 및 섭동모멘트의 관계 규명과 로켓모터 추진 후에 자세운동이 어떻게 변화하는가를 설명하였다.

• Smart Structures and Systems
• /
• 제24권1호
• /
• pp.53-65
• /
• 2019

Misaligned wind-wave and seismic loading render offshore wind turbines suffering from excessive bi-directional vibration. However, most of existing research in this field focused on unidirectional vibration mitigation, which is insufficient for research and real application. Based on the authors' previous work (Sun and Jahangiri 2018), the present study uses a three dimensional pendulum tuned mass damper (3d-PTMD) to mitigate the nacelle structural response in the fore-aft and side-side directions under wind, wave and near-fault ground motions. An analytical model of the offshore wind turbine coupled with the 3d-PTMD is established wherein the interaction between the blades and the tower is modelled. Aerodynamic loading is computed using the Blade Element Momentum (BEM) method where the Prandtl's tip loss factor and the Glauert correction are considered. Wave loading is computed using Morison equation in collaboration with the strip theory. Performance of the 3d-PTMD is examined on a National Renewable Energy Lab (NREL) monopile 5 MW baseline wind turbine under misaligned wind-wave and near-fault ground motions. The robustness of the mitigation performance of the 3d-PTMD under system variations is studied. Dual linear TMDs are used for comparison. Research results show that the 3d-PTMD responds more rapidly and provides better mitigation of the bi-directional response caused by misaligned wind, wave and near-fault ground motions. Under system variations, the 3d-PTMD is found to be more robust than the dual linear TMDs to overcome the detuning effect. Moreover, the 3d-PTMD with a mass ratio of 2% can mitigate the short-term fatigue damage of the offshore wind turbine tower by up to 90%.

• 해양환경안전학회지
• /
• 제21권5호
• /
• pp.552-557
• /
• 2015

본 연구에서는 선미형상을 고려한 조종성능을 심수역 뿐만 아니라 천수역에 대해서 수치 시뮬레이션을 통해 검토하였다. 선미형상을 나타내는 파라메터 중 $C_{wa}$를 미소(${\pm}2%$)하게 변화시킴으로써 각 수역에서의 침로안정성, 선회 및 지그재그 성능이 어떤 변화를 보이고 그 경향이 어떻게 변화하는 지를 검토하였다. 선박의 조종성능 관점에서 흘수 대 수심의 비(=d/H)가 0.5 부근에서의 조종성에 큰 변화를 가져오는 중요 지점임을 알 수 있었고, 비대선(VLCC, 탱커 등)과 세장선(컨테이너)의 경우 선미형상의 변화에 따라 조종성능의 변화 정도가 많은 차이를 가질 수 있음을 알 수 있었다. 또한, $C_{wa}$를 감소(U형에 근접)시키면 선회운동에 있어서 advance 및 tactical diameter가 증가하고, 지그재그 운동에서는 track reach는 증가하지만 각 overshoot angle들은 감소한다. 이와 반대로, $C_{wa}$를 증가(V형에 근접)시키면 선회운동에 있어서 advance 및 tactical diameter는 감소, 지그재그 운동에서는 track reach는 감소, 각 overshoot angle 들은 증가함을 알 수 있었다.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2011년도 제36회 춘계학술대회논문집
• /
• pp.1-2
• /
• 2011

Hybrid rockets have lately attracted attention as a strong candidate of small, low cost, safe and reliable launch vehicles. A significant topic is that the first commercially sponsored space ship, SpaceShipOne vehicle chose a hybrid rocket. The main factors for the choice were safety of operation, system cost, quick turnaround, and thrust termination. In Japan, five universities including Hokkaido University and three private companies organized "Hybrid Rocket Research Group" from 1998 to 2002. Their main purpose was to downsize the cost and scale of rocket experiments. In 2002, UNISEC (University Space Engineering Consortium) and HASTIC (Hokkaido Aerospace Science and Technology Incubation Center) took over the educational and R&D rocket activities respectively and the research group dissolved. In 2008, JAXA/ISAS and eleven universities formed "Hybrid Rocket Research Working Group" as a subcommittee of the Steering Committee for Space Engineering in ISAS. Their goal is to demonstrate technical feasibility of lowcost and high frequency launches of nano/micro satellites into sun-synchronous orbits. Hybrid rockets use a combination of solid and liquid propellants. Usually the fuel is in a solid phase. A serious problem of hybrid rockets is the low regression rate of the solid fuel. In single port hybrids the low regression rate below 1 mm/s causes large L/D exceeding a hundred and small fuel loading ratio falling below 0.3. Multi-port hybrids are a typical solution to solve this problem. However, this solution is not the mainstream in Japan. Another approach is to use high regression rate fuels. For example, a fuel regression rate of 4 mm/s decreases L/D to around 10 and increases the loading ratio to around 0.75. Liquefying fuels such as paraffins are strong candidates for high regression fuels and subject of active research in Japan too. Nakagawa et al. in Tokai University employed EVA (Ethylene Vinyl Acetate) to modify viscosity of paraffin based fuels and investigated the effect of viscosity on regression rates. Wada et al. in Akita University employed LTP (Low melting ThermoPlastic) as another candidate of liquefying fuels and demonstrated high regression rates comparable to paraffin fuels. Hori et al. in JAXA/ISAS employed glycidylazide-poly(ethylene glycol) (GAP-PEG) copolymers as high regression rate fuels and modified the combustion characteristics by changing the PEG mixing ratio. Regression rate improvement by changing internal ballistics is another stream of research. The author proposed a new fuel configuration named "CAMUI" in 1998. CAMUI comes from an abbreviation of "cascaded multistage impinging-jet" meaning the distinctive flow field. A CAMUI type fuel grain consists of several cylindrical fuel blocks with two ports in axial direction. The port alignment shifts 90 degrees with each other to make jets out of ports impinge on the upstream end face of the downstream fuel block, resulting in intense heat transfer to the fuel. Yuasa et al. in Tokyo Metropolitan University employed swirling injection method and improved regression rates more than three times higher. However, regression rate distribution along the axis is not uniform due to the decay of the swirl strength. Aso et al. in Kyushu University employed multi-swirl injection to solve this problem. Combinations of swirling injection and paraffin based fuel have been tried and some results show very high regression rates exceeding ten times of conventional one. High fuel regression rates by new fuel, new internal ballistics, or combination of them require faster fuel-oxidizer mixing to maintain combustion efficiency. Nakagawa et al. succeeded to improve combustion efficiency of a paraffin-based fuel from 77% to 96% by a baffle plate. Another effective approach some researchers are trying is to use an aft-chamber to increase residence time. Better understanding of the new flow fields is necessary to reveal basic mechanisms of regression enhancement. Yuasa et al. visualized the combustion field in a swirling injection type motor. Nakagawa et al. observed boundary layer combustion of wax-based fuels. To understand detailed flow structures in swirling flow type hybrids, Sawada et al. (Tohoku Univ.), Teramoto et al. (Univ. of Tokyo), Shimada et al. (ISAS), and Tsuboi et al. (Kyushu Inst. Tech.) are trying to simulate the flow field numerically. Main challenges are turbulent reaction, stiffness due to low Mach number flow, fuel regression model, and other non-steady phenomena. Oshima et al. in Hokkaido University simulated CAMUI type flow fields and discussed correspondence relation between regression distribution of a burning surface and the vortex structure over the surface.