• Journal of the Korean institute of surface engineering
• /
• v.27 no.2
• /
• pp.65-73
• /
• 1994

Effects of deposition parameter on the ionic conductivity and structural change of the Lithium borosili-cate solid electrolyte films, prepared by rf sputtering using 7$LI_2O-3B_2O_3-1SiO_2$ single phase target and also a mosaic target enriched with $LI_2O$, were analyzed by measuring AC impedance and IR absorption spectra for the films. Thed solid electrolyte film deposited from the single phase target exhibited very low ionic conductivi-ty of $10^{-10}{\Omega}^{-1}cm{-1}$ at room temperature, a result of low $Li^+$ ion content(7.52 at%) in the film. The $Li^+$ con-ductivity for the films deposited from the mosaic target, however, significantly increased to $10^{-7}{\Omega}^{-1}cm{-1}$ due to both an increased $Li^+$content (14.75 at %) and a structural change of the films. The increased ionic conduc-tivity of the film appears to be associated with an easiness of ionic mobility by structural change of glassy film from a some close packed network structure to a open one. These structural changes of film were found to be closely related to the increase in the peak intensity at~$960cm^{-1}$ of IR absorption spectra for the glassy films. With increasing either argon pressure from 3 to 21 mtorr or rf power from 2 to 3 W/$cm^2$, the $Li^+$ conduc-tivity for the films significantly increased to an order of $10^{-6}{\Omega}^{-1}cm{-1}$ due to an increase in openness of film structure, as confirmed by both an increase in the IR absorption peak intensity at ~$960cm^{-1}$ and a resultant reduction of activation energy for mobility of $Li^+$ ion.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2017.05a
• /
• pp.153-153
• /
• 2017

The application of the coating supports the mechanical characteristics of the implant, and various materials and coatings are currently being used in the implant in a way to accelerate adhesion. Especially, plasma electrolytic oxidation (PEO) coating has been proposed continually with good surface treatment of titanium alloys. Also, the PEO process can incorporate Ca and P ions on the titanium surface through variables varied factor. PEO process for bioactive surface has carried out in electrolytes containing Ca and P ions. Natural bone is composed of mineral elements such as Mg, Si, Zn, Sr, and Mn, etc. Especially, Mg and Si of these elements play role in bone formation and growth after clinical implantation of bio-implants. In this study, corrosion charateristics of PEO-treated Ti-6Al-4V alloy in solution containing Si and Mg ions has been investigated using several experimental techniques. The PEO-treated surfaces were identified by X-ray diffraction, using a diffractometer (XRD, Philips X' pert PRO, Netherlands) with Cu $K{\alpha}$ radiation. The morphology was observed by field-emission scanning electron microscopy (FE-SEM, Hitachi 4800, Japan) and energy-dispersive X-ray spectroscopy (EDX, Oxford ISIS 310, England). The potentiodynamic polarization and AC impedance tests for electrochemical degradations were carried out in 0.9% NaCl solution at similar body temperature using a potentiostat with a scan rate of 1.67mV/s and potential range from -1500mV to + 2000mV.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2017.05a
• /
• pp.154-154
• /
• 2017

Ti-6Al-4V alloys are widely used as metal-lic biomaterials in dentistry and orthopedics due to its excellent biocompatibility and me-chanical properties. However, because of low biological activity, it is difficult to form bone growth directly on the surface of titanium implants. For this reason, surface treatment of plasma electrolytic oxidation(PEO) was used for dental implants. To enhance bioac-tivity on the surface, strontium(Sr) and sili-con(Si) ions can be added to PEO treated sur-face in the electrolyte containing these ions. The presence of Sr in the coating enhances osteoblast activity and differentiation, where-as it inhibits osteoclast production and prolif-eration. And Si has been found to be essen-tial for normal bone, cartilage growth, and development. In this study, electrochemical characteristics of Ca, P, Sr, and Si ions from PEO-treated Ti-6Al-4V alloy surface was re-searched using various experimental instruments. DC power is used and Ti-6Al-4V al-loy was subjected to a voltage of 280 V for 3 minutes in the electrolyte containing 5, 10, 20M% Sr ion and 5M% Si ion. The morphol-ogies of PEO-treated Ti-6Al-4V alloy by electrochemical anodization were examined by field-emission scanning electron micro-scopes (FE-SEM), energy dispersive x-ray spectroscopy (EDS), x-ray diffraction (XRD) and corrosion analysis using AC impedance and potentiodynamic polarization test in 0.9% NaCl solution at similar body tempera-ture using a potentiostat with a scan rate of 1.67mV/s and potential range from -1500mV to + 2000mV.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.10 no.7
• /
• pp.2972-2991
• /
• 2016

WLAN is the best choice in the place where complex network is hard to set up. Intelligent terminals are more and more assembled in some areas now. However, according to IEEE 802.11n/802.11ac, the access-point (AP) can only serve one user at a single frequency channel. The spectrum efficiency urgently needs to be improved. In theory, AP with multi-antenna can serve multiple users if these users do not interfere with each other. In this paper, we propose a user clustering scheme that could achieve multi-user selection through the mutual cooperation among users. We focus on two points, one is to achieve multi-user communication with multiple antennas technique at a single frequency channel, and the other one is to use a way of distributed users' collaboration to determine the multi-user selection for user clustering. Firstly, we use the CSMA/CA protocol to select the first user, and then we set this user as a source node using users' cooperation to search other proper users. With the help of the users' broadcast cooperation, we can search and select other appropriate user (while the number of access users is limited by the number of antennas in AP) to access AP with the first user simultaneously. In the network node searching, we propose a maximum degree energy routing searching algorithm, which uses the shortest time and traverses as many users as possible. We carried out the necessary analysis and simulation to prove the feasibility of the scheme. We hope this work may provide a new idea for the solution of the multiple access problem.

• Transactions of Materials Processing
• /
• v.17 no.8
• /
• pp.594-599
• /
• 2008

This paper presents a micro air pump based on the synthetic jet to supply reactant at the cathode side for micro fuel cells. The synthetic jet is a zero mass flux device that converts electrical energy into the momentum. The synthetic jet actuation is usually generated by a traditional PZT-driven actuator, which consists of a small cylindrical cavity, orifices and PZT diaphragms. Therefore, it is very important that the design parameters are optimized because of the simple configuration. To design the synthetic jet micro air pump, a numerical analysis has been conducted for flow characteristics with respect to various geometries. From results of numerical analysis, the micro air pump has been fabricated by the PDMS replication process. The most important design factors of the micro air pump in micro fuel cells are the small size and low power consumption. To satisfy the design targets, we used SP4423 micro chip that is high voltage output DC-AC converter to control the PZT. The SP4423 micro chips can operate from $2.2{\sim}6V$ power supply(or battery) and is capable of supplying up to 200V signals. So it is possible to make small size controller and low power consumption under 0.1W. The size of micro air pump was $16{\times}13{\times}3mm^3$ and the performance test was conducted. With a voltage of 3V at 800Hz, the air pump's flow rate was 2.4cc/min and its power consumption was only 0.15W.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.487-487
• /
• 2012

플라즈마 디스플레이 패널(PDP)은 공정 절차가 간단하고 가격 경쟁력이 매우 뛰어나 일찌감치 대형 평판 디스플레이 시장을 주도해 왔으며 빠른 응답 속도를 기반으로 한 생생한 화질의 구현으로 3D TV 시장에서도 꾸준한 사랑을 받고 있다. 향후 더 큰 화면을 요구하는 PID(Public Information Display) 시장에서도 PDP 는 두각을 나타낼 수 있을 것으로 보인다. 하지만 PDP 는 여전히 LCD, OLED 등의 디스플레이에 비해 발광 효율이 낮고 소비 전력이 높다는 단점을 가지고 있다. 또한 미국 환경청(EPA)과 에너지부(DOE)가 공동으로 마련한 전자 제품의 효율 등급제인 에너지 스타(Energy Star) 제도가 끊임없이 개편되면서 소비 전력에 대한 규제가 점차 강화되고 있기 때문에 발광 효율 및 소비 전력 특성의 개선은 현재 PDP 업계가 해결해야 할 가장 중요한 과제라고 할 수 있다. 발광 효율의 개선과 관련하여 최근에는 PDP의 보호막으로 널리 쓰이고 있는 MgO 보다 2차 전자 방출 계수가 높아 PDP의 구동 전압을 낮추는 동시에 휘도와 발광 효율 특성을 개선시킬 수 있는 신 보호막에 대한 연구가 활발히 이루어지고 있다. MgO를 대체 가능한 신 보호막으로 언급되는 물질은 SrO 혹은 CaO 등이 대표적이다. 하지만 이러한 물질들은 공기 및 수분에 대한 용해도가 높기 때문에 증착된 막이 이후의 공정 과정(합착 및 가열 배기 등)에서 대기 중에 노출 될 경우 심하게 변질될 수 있다. 이러한 문제점을 해결하기 위해서 신 보호막 위에 기존의 MgO 보호막을 얇게 증착하여 공기로부터의 접촉을 차단하거나 펠렛을 제조하는 과정에서 MgO 에 신 보호막 물질을 소량만 첨가하는 등의 방법들이 제안되어 왔으며 그 결과 기존의 PDP 대비 구동 전압을 낮추고 발광 효율을 획기적으로 개선하는데 성공한 결과들이 지속적으로 보고되고 있다. 하지만 신 보호막이 공기 및 수분에 민감한 만큼, 고온의 공정으로 인해 PDP의 하판 유리로부터 상판에 증착된 박막으로 확산되는 불순물에 의해서도 오염되며 이 역시 신 보호막의 특성을 구현하는데 방해 요소로 작용한다. 본 연구에서는 PDP 하판의 불순물이 상판의 박막으로 확산되는 것을 방지하고자 하판 형광체 인쇄전 PECVD 증착법으로 확산 방지막을 1 가량 형성하였다. 이후 SIMS 분석을 통하여 하판 불순물의 확산이 효과적으로 차단됨을 확인하였고 신 보호막의 오염을 최소화하여 결과적으로 PDP의 구동 전압을 낮추고 효율을 획기적으로 개선하는데 기여할 수 있음을 확인하였다.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.24 no.5
• /
• pp.44-54
• /
• 2010

Optimal efficiency control of synchronous reluctance motor(SynRM) is very important in the sense of energy saving and conservation of natural environment because the efficiency of the SynRM is generally lower than that of other types of AC motors. This paper is proposed a novel efficiency optimization control of SynRM considering iron loss using multi adaptive fuzzy learning controller(AFLC). The optimal current ratio between torque current and exciting current is analytically derived to drive SynRM at maximum efficiency. This paper is proposed an efficiency optimization control for the SynRM which minimizes the copper and iron losses. There exists a variety of combinations of d and q-axis current which provide a specific motor torque. The objective of the efficiency optimization control is to seek a combination of d and q-axis current components, which provides minimum losses at a certain operating point in steady state. The control performance of the proposed controller is evaluated by analysis for various operating conditions. Analysis results are presented to show the validity of the proposed algorithm.

• Journal of Magnetics
• /
• v.16 no.3
• /
• pp.211-215
• /
• 2011

The dynamic magnetostriction characteristics of an Fe-based nanocrystalline FeCuNbSiB alloy are investigated as a function of the dc bias magnetic field. The experimental results show that the piezomagnetic coefficient of FeCuNbSiB is about 2.1 times higher than that of Terfenol-D at the low dc magnetic bias $H_{dc}$ = 46 Oe. Moreover, FeCuNbSiB has a large resonant dynamic strain coefficient at quite low Hdc due to a high mechanical quality factor, which is 3-5 times greater than that of Terfenol-D at the same low $H_{dc}$. Based on such magnetostriction characteristics, we fabricate a new type of transducer with FeCuNbSiB/PZT-8/FeCuNbSiB. Its maximum resonant magnetoelectric voltage coefficient achieves ~10 V/Oe. The ME output power reaches 331.8 ${\mu}W$ at an optimum load resistance of 7 $k{\Omega}$ under 0.4 Oe ac magnetic field, which is 50 times higher than that of the previous ultrasonic-horn-substrate composite transducer and it decreases the size by nearly 86%. The performance indicate that the FeCuNbSiB/PZT-8/FeCuNbSiB transducer is promising for application in highly efficient magnetoelectric energy conversion.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.41 no.3
• /
• pp.101-108
• /
• 2004

A 16-bit adiabatic ALU(arithmetic logic unit) is designed. A simplified four-phase clock generator is also designed to provide supply clocks for the adiabatic circuits. All the clock line charge on the capacitive interconnections is recovered to recycle energy. Adiabatic circuits are designed based on ECRL (efficient charge recovery logic) using a 0.35${\mu}{\textrm}{m}$ CMOS technology. The post-layout simulation results show that the power consumption of the adiabatic ALU including supply clock generator is reduced by a factor of 1.15-1.77 compared to the conventional CMOS ALU with the same structure.

• Proceedings of the Korean Vacuum Society Conference
• /
• 1999.07a
• /
• pp.212-212
• /
• 1999

Ar-O2 분위기의 Plasma 표면 처리된 OPP 의 polymer 위에 약 400$\AA$ 정도로 sputter 코팅된 Al의 부착력에 관하여 연구를 하였다. 금속과 polymer와 같이 성질이 서로 다른 물질이 서로 결합할 때 접착력은 제품의 성능과 신뢰도를 결정하는데 매우 중요한 인자이다. 최근 고분자재료의 표면을 플라즈마 처리 (plasma surface treatment)에 의해 고분자와 금속도포(coating) 층간의 접착력향상에 따라, 증착필름 및 인쇄용 필름 등의 기능도 향상시킬 수 있다. 저온 plasma를 이용한 표면처리는 plastic 재료가 가지고 있는 기본적인 특성을 저해하지 않고, 그 표면 층만을 개량하는 plasma 또는 sputter etching 갚은 electrical discharge 방법은 진공 증착 방식에서 많이 사용되고 있다. 7$\mu\textrm{m}$의 두께 OPP polymer를 10m/min의 속도로 OPP의 표면을 연속 plasma pretreatment를 하였다. 5$\times$10-2torr에서, PEM(Plasma Emission Monitor)를 이용하여 plasma intensity에 따른 Ar/O2비를 변화시키면서 test를 하였다. AFM과 XPS를 이용하여 OPP의 표면분석을 하였다. 이 plasma처리는 기존의 D.C plasma 처리 방식과는 달리 Midium frequency AC voltage hollow cathod 방식으로 plasma를 발생된 high energy plasma 분위기를 만들 수 있다. 이러한 방식은 -cycle일 때 plasma로부터 발생된 전자가 polymer 표면을 bombard 하게 되고, +cycle 일 때 polymer 표면이 cathod 가 되어 active ion에 의해 sputtering 이 된다. 이때 plasma 처리기의 polymer 기판 후면에 magnet를 설치하여 높은 ionization을 발생시켜 처리 효과를 한층 높여 주었다. 이 plasma 처리는 표면 청정화, 표면 etching 이 동시에 행하는 것과 함께 장시간 처리에 의해 표면에서는 미세한 과, C=C기, -C-O-의 극성기의 도입에 의한 표면 개량이 된다는 것을 관찰할 수 있다. OPP polymer 표면을 Ar 100%로 plasma 처리한 경우 C-O, C=O 등의 carbonyl가 발생됨을 알 수 있었다. C-O, C=O 등의 carbynyl polor group이 도입됨에 따라 sputter된 Al의 접착력이 향상됨을 알 수 있으며, TEM 관찰 결과 grain size도 상당히 작아짐을 알 수 있었다.