• 한국전기전자재료학회논문지
• /
• 제27권4호
• /
• pp.262-267
• /
• 2014

This study describes that light flicker of LED lamp is improved by placing an AC-powered LED block in each phase of three-phase AC power. Rectified current is considered as an instantaneous luminous flux because the current flowing through the LED block is proportional to the amount of light emitted by the LED block. Percent flicker is calculated simply by modeling the rectified current flowing through the LED block to a triangular wave current. Percent flicker is 100% in single-phase AC powered LED lamp. Percent flicker of the same level as that in an incandescent lamp (6%~14%) is however, achieved if light emission starts before $40^{\circ}$ in each voltage phase of three-phase AC power.

• 전력전자학회논문지
• /
• 제8권2호
• /
• pp.173-179
• /
• 2003

본 논문은 3상 PWM 컨버터의 커패시터의 용량을 온라인으로 추정하는 새로운 기법을 제안한다. 무부하 상태의 PWM 컨버터에 저주파수의 입력전류를 주입하면 직류링크단에 이에 대응되는 리플전압이 발생된다. 직류링크단의 리플전압과 전류를 검출하여 커패시터의 용량을 계산한다. 제안된 방법에 의해 계산된 커패시터의 용량의 추정오차는 2% 이내이다.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제49권11호
• /
• pp.589-595
• /
• 2000

In this papre, AC losses of Bi-2223 tapes with different twist pitch of superconducting core were fabricated, measured and analyzed. These samples produced by a powder-in-tube method are multi-filamentary tape with Ag matrix. Also, it's produced by non-twist and different twist pitch(8, 10, 13, 30, 50, 70 mn). The critical current measurement was carried out under the environment in Liquid nitrogen and in zero field by 4-probe method. And the AC loss measurement was carried out under the environment of applied time-varying transport current by transport method. From experiment, the critical current is larger non-twist than twisted filament. And, the AC loss by Norris equation is higher non-twisted tape than 13mm twisted tape. Also, it is confirmed that of AC loss of tape having non-twist pitch larger than those having differnet twist pitch.

• 한국가스학회지
• /
• 제5권3호
• /
• pp.63-72
• /
• 2001

천연가스 공급용 고압 지하 매설배관에 교류가 유도될 때 쿠폰과 전기저항형 박막센서를 이용하여 교류에 의한 부식속도를 평가하고 주요한 인자를 규명하고자 하였다. 전국에 걸쳐 조사된 교류전압 측정결과를 바탕으로 쿠폰과 전기저항형 박막센서를 설치하고, 주요인자를 고찰하기 위하여 다양한 인자들 (교류전압, 교류전류, 토양 비저항, 주파수, 방식전위)을 정기적으로 기록하였다. 황산동 전극기준 -850mV의 방식전위를 충분히 만족하는 상황에서도 교류에 의한 부식이 진행하였으며, 교류에 의한 부식속도는 교류전압과는 관계없이 교류전류밀도와 주파수에 의존하는 것으로 나타났다. 교류에 의한 부식속도는 유효교류전류밀도에 따라 직선적으로 증가하였으며, 쿠폰에 의한 평가결과 직선의 기울기는 0.619, 전기저항형 센서에 의한 직선의 기울기는 0.885로 나타났다.

• 전기전자학회논문지
• /
• 제27권4호
• /
• pp.477-485
• /
• 2023

본 논문에서는 AC 리플이 리튬 이온 배터리의 수명에 미치는 영향을 실험적으로 분석한다. 에너지 저장 시스템(ESS)의 이용 효율을 높이기 위해 양방향 전력변환시스템(PCS)이 사용되며, 계통 연계 시 구조상 계통 주파수의 2배의 주파수를 갖는 전류 리플이 배터리에 인가되게 된다. 따라서, AC 리플이 Li-ion 배터리의 노화에 미치는 영향에 대해 분석하기 위해 DC 및 DC+AC 리플 사양의 충/방전 프로파일을 적용하여 노화 실험이 수행되었다. 실험 결과를 바탕으로 직류 내부 저항(DCIR), 증분 용량(IC), 표면 온도를 분석하였다. 결과적으로 AC 리플이 노화에 직접적으로 영향을 미치지 않으며 특정 주기 이 후 배터리 노화가 둔화되는 것을 확인하였다. 이러한 결과는 AC 리플이 발생하는 어플리케이션에서 전류 리플을 줄이기 위해 적용된 필터를 개선하는 데 도움이 될 수 있다.

• Advances in materials Research
• /
• 제13권3호
• /
• pp.153-160
• /
• 2024

This study investigates the application of alternating current (AC) and direct current (DC) anodization techniques on stainless steel 304L (SS304L) in an ethylene glycol and ammonium fluoride (NH4F) electrolyte solution to produce a nano-porous oxide layer. With limited research on AC anodizing of stainless steel, this study focuses on comparing AC and DC anodization in terms of current density versus time response, phase analysis using X-ray diffraction (XRD), and corrosion rate determined by linear polarization. Both AC and DC anodization were performed for 60 minutes at 50 V in an electrolyte solution containing 0.5% NH4F and 3% H₂O in ethylene glycol. The results show that AC anodization exhibited higher current density compared to DC anodization. XRD analysis revealed the presence of ferrite (α-Fe) and austenite (γ-Fe) phases in the as-received specimen, while both AC and DC anodized specimens exhibited only the γ-Fe phase. The corrosion rate of the AC-anodized specimen was measured at 0.00083 mm/year, lower than the corrosion rate of the DC-anodized specimen at 0.00197 mm/year. These findings indicate that AC anodization on stainless steel offers advantages in terms of higher current density, phase transformation, and lower corrosion rate compared to DC anodization. These results highlight the need for further investigation and exploration of AC anodization as a promising technique for enhancing the electrochemical properties of stainless steel.

• Journal of Power Electronics
• /
• 제3권4호
• /
• pp.249-258
• /
• 2003

This paper presents a high-efficient and cost effective three-phase AC/DC-DC/AC power conversion system with a single two-switch type active Auxiliary Resonant DC Link (ARDCL) snubber circuit, which can minimize the total power dissipation. The active ARDCL snubber circuit is proposed in this paper and its unique features are described. Its operation principle in steady-state is discussed for the three phase AC/DC-DC/AC converter, which is composed of PWM rectifier as power factor correction (PFC) converter, sinewave PWM inverter. In the presented power converter system not only three-phase AC/DC PWM rectifier but also three-phase DC/AC inverter can achieve the stable ZVS commutation for all the power semiconductor devices. It is proved that the proposed three-phase AC/DC-DC/AC converter system is more effective and acceptable than the previous from the cost viewpoint and high efficient consideration. In addition, the proposed two-switch type active auxiliary ARDCL snubber circuit can reduce the peak value of the resonant inductor injection current in order to maximize total system actual efficiency by using the improved DSP based control scheme. Moreover the proposed active auxiliary two-switch ARDCL snubber circuit has the merit so that there is no need to use any sensing devices to detect the voltage and current in the ARDCL sunbber circuit for realizing soft-switching operation. This three-phase AC/DC-DC/AC converter system developed for UPS can achieve the 1.8% higher efficiency and 20dB lower conduction noise than those of the conventional three-phase hard-switching PWM AC/DC-DC/AC converter system. It is proved that actual efficiency of the proposed three-phase AC/DC-DC/AC converter system operating under a condition of soft switching is 88.7% under 10kw output power.

• 조명전기설비학회논문지
• /
• 제24권12호
• /
• pp.9-16
• /
• 2010

In this paper, we have proposed a new dimmable magnetic ballast for HID(High Intensity Discharge) lamps consisted of AC switches to variate inductance value by using Silicon Controlled Rectifiers and the isolated zero current detector on inductor. Conventional dimming ballast has used relays or Solid State Relays in AC switches. However, a relay is difficult to zero current switching, because it has long operating time(10[ms]), and price competitiveness of SSR is very low. The proposed AC switches are suitable to switch at zero inductor current and it is accurately detected by using a opto-coupler. SCR is cheaper than SSR, and it is suitable to switch at zero inductor current because SCR is automatically turned off under holding current at no gate signal. Operating principles, simulation results and experimental results of the proposed ballast are described.

• Journal of Power Electronics
• /
• 제6권1호
• /
• pp.67-72
• /
• 2006

This paper introduces two different types of AC current control methods for an indirect vector controlled induction motor using a matrix converter. The proposed methods combine the advantages of matrix converters with the advantages of the indirect vector AC current control methods. The first proposed method explains the basic idea of the hysteresis current control method for matrix converters and shows its capability and stability in comparison to the conventional method usually used for VSI. With the aid of the special configuration of the matrix converter, we also propose another current method which is modified from the first one in order to reduce both current ripple and torque ripple. Simulation results have verified the feasibility and the effectiveness of the proposed methods.

• Journal of Welding and Joining
• /
• 제21권2호
• /
• pp.57-63
• /
• 2003

Since new types of vehicles or structures made from thin aluminum alloy are under rapid development and some products are already on the market, welding of aluminium sheet is increasing. MIG(Metal Inert Gas), MIG-Pulse, TIG(Tungsten Inert Gas) welding are the typical Ai welding. MIG welding has the advantage of high speed, but it is difficult to apply to the thin plate, because of bum-through by the high heat input and spatter. MIG-Pulse welding can weld without spatter and burn-through, but when the gap exists at the welding joint, there is quite a possibility of bum-through. TIG welding is difficult to weld at a high speed. AC Pulse welding alternates between DCEP(Direct Current Electrode Positive) and DCEN(Direct Current Electrode Negative). DCEN is higher wire melting rate than DCEP, while lower temperature of droplet than DCEP. In AC Pulse welding, far fixed welding current, wire melting rate increases as the EN ratio increases. For fixed wire feed rate, welding current decreases as the EN ratio increases. Because of these features, the temperature of droplet, the depth of penetration, the width of bead decrease and the reinforcement height increases as EN ratio increases, and these are able to weld at a high speed, lower heat input. It is the purpose of this study that design of AC pulse current waveform for MIG welding of Al sheet and estimation of output characteristic.