• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.4 no.2
• /
• pp.83-87
• /
• 2011

Clock selection has a significant impact on the performance and quality of designs in high-level synthesis. Almost systems require that the clock length is required prior to scheduling, the best value of the clock can be found only after evaluating different schedules. In this study, we presents a scheduling method that works simultaneously with synthesis by selecting a clock from a chainable operation set. Our scheduling algorithm is based on list scheduling and executes chaining considering bit level delays based on selected clock period. Experimental results show that our method improves the performance by 18 percent.

• Journal of the Korean Institute of Telematics and Electronics B
• /
• v.31B no.3
• /
• pp.91-102
• /
• 1994

For the analysis of textured image, it requires large storage space and computation time to calculate the matrix features such as SGLDM(Spatial Gray Level Dependence Matrix). NGLDM(Neighboring Gray Level Dependence Matrix). NSGLDM(Neighboring Spatial Gray Level Dependence Matrix) and GLRLM(Gray Level Run Length Matrix). In spite of a large amount of information that each matrix contains, a set of several correlated scalar features calculated from the matrix is not sufficient to approximate it. In this paper, we propose a new classifier for textured images based on these matrices in which the projected vectors of each matrix on the meaningful directions are used as features. In the proposed method, an unknown image is classified to the class of a known image that gives the maximum similarity between the projected model vector from the known image and the vector from the unknown image. In the experiment to classify images of agricultural products, the proposed method shows good performance as much as 85-95% of correct classification ratio.

• Journal of computational fluids engineering
• /
• v.22 no.1
• /
• pp.81-87
• /
• 2017

The characteristics of flow past a square cylinder submerged under the free surface have been numerically studied. An immersed boundary method was adopted for implementation of the cylinder cross-section in a Cartesian grid system. Also, a level-set method was used to capture the interface of the two fluids. The case for Reynolds number 150 was examined. At the specific Reynolds number, by varying the gap ratio(0.25, 0.40, 0.55, 0.70, 1.00, 1.50, 2.50, 5.00) the effects of the free surface on the force coefficients and Strouhal number of vortex shedding were identified. The presence of the free surface very close to the cylinder significantly affects the shedding pattern, resulting in considerable deviation of the force coefficients and Strouhal number from those of the single-phase flow. In addition, the influence of Froude number was considered in this study. By increasing Froude number(0.2-0.4), flow topology change was identified at the specific gap ratios(0.40, 0.70, 1.50, 5.00).

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.67 no.3
• /
• pp.419-426
• /
• 2018

An useful and effective design method for the gas identification system is presented in this paper. The proposed gas identification system adopts hierarchical structure with two level rule base combining fuzzy sets with rough sets. At first, a hybrid genetic algorithm is used in grouping the array sensors of which the measured patterns are similar in order to reduce the dimensionality of patterns to be analyzed and to make rule construction easy and simple. Next, for low level identification, fuzzy inference systems for each divided group are designed by using TSK fuzzy rule, which allow handling the drift and the uncertainty of sensor data effectively. Finally, rough set theory is applied to derive the identification rules at high level which reflect the identification characteristics of each divided group. Thus, the proposed method is able to accomplish effectively dimensionality reduction as well as accurate gas identification. In simulation, we demonstrated the effectiveness of the proposed methods by identifying five types of gases.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2007.04a
• /
• pp.238-241
• /
• 2007

We present an innovative method of multi-physics application involving energetic materials. Energetic materials are related to reacting flows in extreme environments such as fires and explosions. They typically involve high pressure, hish temperature, strong non-linear shock waves, and high strain rate deformation of metals. We use an Eulerian methodology to address these problems. Our approach is naturally free from large deformation of materials that makes it suitable for high strain-rate multi-material interaction problems. Furthermore we eliminate the possible interface smearing by using the level sets. We have devised a new level set based tracking framework that can elegantly handle large gradients typically found in reacting gases and metals. We show several work-in-progress applications of our algorithm including the Taylor impact test, explosive venting and additional confined explosion problems of modem interest.

• Proceedings of the KIPE Conference
• /
• 2000.07a
• /
• pp.38-40
• /
• 2000

In this paper we propose a calculation method for fuzzy control based on quantized $\alpha$-cut decomposition of fuzzy sets. This method is easy to be implemented in analog hardware. The effect of quantization levels on defuzzified fuzzy inference results is investigated. A few quantization levels are sufficient for fuzzy control. The hardware implementation of this calculation method and the defuzzification by gravity center method by PWM are also presented.

• Proceedings of the IEEK Conference
• /
• 1998.06a
• /
• pp.223-226
• /
• 1998

The control objective of steam generator water level in the secondary circuit of a nuclear power plant is to regulate the water level at the desired set point. The dynamics of steam generators is non-linear in nature. The task of modelling such plant is very difficult and especially so when plant operating conditions change frequently. In these reasons, conventional PI gains over all pover range will not work efficiently and a manual control is generally used in low power operation. Therefore the robust H$\infty$ controller design method should be required. In this paper, we design the robust H$\infty$ controller for water level control of steam generator using a mixed H$\infty$ optimization with model-matching method. Firstly we choose the desired model that has good disturbance rejection performance. Secondly we design a stabilizing controller to keep the model-matching error small and also provide sufficiently large stability margin against additive perturbations of the nominal plant.

• 한국전산유체공학회:학술대회논문집
• /
• 2010.05a
• /
• pp.376-379
• /
• 2010

Bubble rising phenomenon is widely founded in many industrial applications such as a stream generator in power plant. Many experimental and numerical researches have been already performed to predict dynamic behavior of the bubble rising process. Recently numerical approaches are getting popular since it can offer much detailed information which is almost impossible to obtain from the experiments. Rising bubble could penetrate through the top free surface which makes the problem much more complicate in addition to the phase changing effect even with latest numerical techniques. In this paper, the top free surface effect on rising bubble has been investigated. The gas-liquid interface was explicitly tracked using high-order Level Contour Reconstruction Method(LCRM) which is a hybridization of Front-Tracking and Level-Set method. Break-up behavior of rising bubble at free surface showed different characteristics with initial diameter of bubble.

• Proceedings of the Korean Operations and Management Science Society Conference
• /
• 2002.05a
• /
• pp.272-279
• /
• 2002

A common task in assembly modeling is the determination of the position and orientation of a set of components by solving the spatial relationships between them. Assembly models could be constructed at various levels of abstraction. They could be classified into component or geometry-level assembly models. The geometry-level assembly design approach using mating constraints such as against and fits is widely used in the commercial modelers, but it may be very tedious in some cases fur designer. In this paper, we propose a new method to construct an assembly model at the component-level by extracting joint mating features from the kinematics constraints specified between components. The assembly model constructed using the proposed method includes hierarchical and relational assembly models, component/sub-assembly positions and degrees of freedom information. The proposed method is more intuitive and natural way of assembly design and it guarantees the topological robustness of assembly modification such as component replacement and modification.

• Nuclear Engineering and Technology
• /
• v.53 no.1
• /
• pp.30-43
• /
• 2021

In the 2D/1D method, a global adjoint CMFD based on the generalized equivalence theory is built to synthesize the 2D radial MOC adjoint and 1D axial NEM adjoint calculation and also to accelerate the iteration convergence of 3D whole-core adjoint transport calculation. Even more important, an advanced yet accurate two-level (TL) CMFD acceleration technique is proposed, in which an equivalent one-group adjoint CMFD is established to accelerate the multi-group adjoint CMFD and then to accelerate the 3D whole-core adjoint transport calculation efficiently. Based on these method, a new code is developed to perform 3D adjoint neutron flux calculation. Then a set of VERA and C5G7 benchmark problems are chosen to verify the capability of the 3D adjoint calculations and the effectiveness of TL CMFD acceleration. The numerical results demonstrate that acceptable accuracy of 2D/1D adjoint calculations and superior acceleration of TL CMFD are achievable.