• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 추계학술대회논문집B
• /
• pp.627-632
• /
• 2000

Developing turbulent flows in a rotating 90 degree bend with square cross-section were measured by a hot-wire anemometer. The six orientation hot-wire technique was applied to measured the distributions of 3 mean velocities and 6 Reynolds stress components. Effects of Coriolis and centrifugal forces caused by the curvature and rotation of bend on the mean motion and turbulence structures were experimentally investigated Productive addition of Coriolis and centrifugal forces to the outward radial direction in the entrance region of bend increases the secondary flow intensity according to the rotational speeds. However, after 45 degree of bend, centrifugal force due to the rotation of bend may promote the break down of counter rotating vortex pair into multi-cellular pattern, thereby decreasing the production rate of turbulence energy and Reynolds stresses.

• 한국운동역학회지
• /
• 제17권1호
• /
• pp.61-68
• /
• 2007

The purpose of this study was to analyze the shoulder joint torque and muscle pattern performing as Tennis serve by Isokinetic motions on Isomed 2000. The subject, who was 5 males Korean national high school tennis players. By analyzing the flexion/extension of the shoulder, the peak torque of the internal/external rotation motion(at 60,180 and 300 degree/sec) at peak torque degree, the weight, peak torque, and power. combined with the timing of the electrode of the attached trapezius and posterior deltoid at the three part. From the data analysis & discussion the following conclusions were drawn. When doing a shoulder extension, the peak torque can be widely seen at 60degree per second. However the degree may be different depending on angular velocity. When doing an internal rotation at 90degree abduction, peak torque per weight was seen at 60degree per second. The degree of peak torque was at 31.6-44.2 and peak power was faster when angular velocity was increased. The aspect of muscle pattern was seen more at the internal rotation in the 90degree abduction rather than the shoulder extension. However the angular velocity was not influenced by muscle mobilization(in order of anterior deltoid, posterior deltoid and trapezius. To properly apply the above conclusion, when tennis players serve it is better the elbow be impacted by the extension. when doing isokinetic motion it is better to increase angular velocity and improve muscle power. also the anterior deltoid amongst the shoulder muscle should be improved to develop serve speed.

• 소성∙가공
• /
• 제27권5호
• /
• pp.301-313
• /
• 2018

In this paper, tensile test was performed on pure titanium sheet (CP Ti sheet) with HCP structure in each direction to evaluate mechanical and surface properties and analyze microstructural changes during plastic deformation. We also evaluated forming limits of Ti direction in dome-type punch stretching test using a non-contact three-dimensional optical measurement system. As a result, it was revealed the pure titanium sheet has strong anisotropic property in yield stress, stress-strain curve and anisotropy coefficient according to direction. It was revealed that twinning occurred when the pure titanium sheet was plastic deformed, and tendency depends differently on direction and deformation mode. Moreover, this seems to affect the physical properties and deformation of the material. In addition, it was revealed the pure titanium sheet had different surface roughness changes in 0 degree direction and 90 degree direction due to large difference of anisotropy, and this affects the forming limit. It was revealed the forming limit of each direction obtained through the punch stretching test gave higher value in 90 degree direction compared with forming limit in 0 degree direction.

• 한국표면공학회지
• /
• 제42권2호
• /
• pp.95-101
• /
• 2009

This study is the research on the thermal emissivity depending on the bulk graphite's alignment degree. Bulk graphites were manufactured by uni-axial pressing and subsequent heat treatment of natural graphite flakes with organic binder. The samples were prepared to be $0^{\circ}$ (relative to the 002 c-face), $45^{\circ}$, and $90^{\circ}$ (relative to the 100 a-face) for measuring alignment degree. The alignment degree of the sample was measured by XRD. The thermal emissivity was measured by infrared thermal image camera at $100^{\circ}C$ and compared with the value obtained by Infrared spectroscopy. The alignment degree and thermal emissivity of $0^{\circ}$ sample were measured to be 0 and 0.70 respectively. And those of $90^{\circ}$ sample were 0.73 and 0.80 respectively. The emissivity value was correlated with obtained by IR spectroscopy. Therefore it was considered that the thermal emissivity of the bulk graphite is correlated with the alignment degree.

• 대한토목학회논문집
• /
• 제32권6C호
• /
• pp.305-314
• /
• 2012

본 연구에서는 미소파괴음을 활용하여 한국 원자력 연구원 지하처분연구시설에서 채취한 화강암의 손상도를 정량적으로 평가하였다. 해석결과 균열손상기준은 균열개시, 균열손상응력은 일축압축강도의 약 48%, 72%이며 균열손상기준에 따른 암석의 손상은 시료에 가해지는 응력이 균열손상응력을 초과하면서부터 0.06에서 일축압축강도의 80%, 90%에서는 0.34, 0.60로 급격히 증가하였다. 이는 축 방향 변형계수를 활용한 손상도 결과와 유사하여 단순회귀분석 결과 두 기법의 상관관계는 0.90로 상관성은 매우 높은 것으로 나타났다. 이에 미소파괴음 에너지를 활용한 손상도 결과와 모어-쿨롱 파괴규준을 이용하여 응력수준에 따른 축 방향 변형계수, 암석의 강도, 점착력, 내부마찰각 변화를 분석한 결과 균열손상응력 이전까지는 원결과보다 각각 6%, 12%, 7%, 3% 감소하였지만 일축압축강도의 90%수준에서는 69%, 72%, 62%, 24%로 감소의 기울기는 급격히 증가하였다.

• 한국지하수토양환경학회:학술대회논문집
• /
• 한국지하수토양환경학회 2003년도 추계학술발표회
• /
• pp.302-305
• /
• 2003

The electrokinetic remediation tests for natural soil contaminated by lead are performed on unsaturated conditions, in which the degree of saturation is controlled through the changes in water content and the constant unit weight. At the degree of saturation of 70% the small acid range and electrical potential is developed. The changes in the water content are little above the saturation of 90%. But it is increased by 1.7 times at the degree of saturation of 70%. Finally, the efficiency of extraction is improved at 70% than 100%.

• 융합신호처리학회논문지
• /
• 제14권1호
• /
• pp.39-44
• /
• 2013

본 논문에서는 멀티암(multi-arm) 스파이럴 안테나용 디지털 위상천이기(digital phase-shifter)를 힐버트 변환(Hillbert transform)을 이용하여 설계하였다. 힐버트 변환은 입력신호에 포함된 모든 주파수 성분을 $90^{\circ}$ 위상천이 시키며, 퓨리에 변환(Fourier transform)과 역퓨리에 변환(Inverse FIT)을 통해 구현된다. 디지털 위상천이기는 ADC(Analog-digital converter)로 샘플링된 입력신호에 힐버트 변환을 적용하여 위상차가 $90^{\circ}$인 두 신호를 생성하고, 이 두 신호를 이용하여 입력신호의 위상을 천이위상만큼 천이시키게 한다. 힐버트 변환 기반의 디지털 위상천이기는 Xilinx사의 System generator로 설계되었고, 입력 잡음, FFT 포인트 수, 샘플링 주기, 입력신호의 초기위상 및 천이 위상각 등에 따른 위상천이 성능을 시뮬레이션 하였으며, Matlab 결과와 비교하여 일치함을 확인하였다.

• 한국산업정보학회논문지
• /
• 제15권2호
• /
• pp.11-16
• /
• 2010

본 논문에서는 180도 방위 빔 커버리지 특성을 갖는 소형의 고이득 빔 조향 기생 배열 안테나를 제안한다. 이 안테나는 단일면 야기 다이폴 급전소자와 리액턴스가 장하된 인접한 두 기생 다이폴 소자로 구성되며 제작된 안테나는 기생소자의 리액턴스를 전자적으로 변화시킴으로써 UNII 대역에서 (5.725GHz~5.825GHz) 방위각$-90^{\circ}$에서 $90^{\circ}$범위에서 5.2dB~6.7dB 이득 특성을 가지며, 반사손실은 -10dB이하임을 측정을 통해 확인하였다.

• Journal of the Korean Association of Oral and Maxillofacial Surgeons
• /
• 제32권1호
• /
• pp.52-59
• /
• 2006

Purpose: The purpose of this study was to evaluate the influence of apical-coronal implant position on the stress distribution after occlusal and oblique loading. Materials and Methods: The cortical and cancellous bone was assumed to be isotropic, homogeneous, and linearly elastic. The implant was apposed to cortical bone in the crestal region and to cancellous bone for the remainder of the implant-bone interface. The cancellous core was surrounded by 2-mm-thick cortical bone. An axial load of 200 N was assumed and a 200-N oblique load was applied at a buccal inclination of 30 degrees to the center of the pontic and buccal cusps. The 3-D geometry modeled in Iron CAD was interfaced with ANSYS. Results: When only the stress in the bone was compared, the minimal principal stress at load Points A and B, with a axial load applied at 90 degrees or an oblique load applied at 30 degrees, for model 5. The von Mises stress in the screw of model 5 was minimal at Points A and B, for 90- and 30-degree loads. When the von Mises stress of the abutment screw was compared at Points A and B, and a 30-degree oblique load, the maximum principal stress was seen with model 2, while the minimum principal stress was with model 5. In the case of implant, the model that received maximum von Mises stress was model 1 with the load Point A and Point B, axial load applied in 90-degree, and oblique load applied in 30-degree. Discussion and Conclusions: These results suggests that implantation should be done at the supracrestal level only when necessary, since it results in higher stress than when implantation is done at or below the alveolar bone level. Within the limited this study, we recommend the use of supracrestal apical-coronal positioning in the case of clinical indications.

• 대한교통학회:학술대회논문집
• /
• 대한교통학회 1999년도 제36회 학술발표회논문집
• /
• pp.90-95
• /
• 1999