• Journal of Korean Society of Water and Wastewater
• /
• v.20 no.2
• /
• pp.289-294
• /
• 2006

A pilot scale non-woven fabric filter separation activated sludge system was investigated for practical application on domestic wastewater reclamation and reuse. The system was operated in A/O (Anaerobic/Oxic) process with submerged filter module in the aerobic compartment. In the test of two types of filter materials ($70g/m^2$ and $35g/m^2$), the initial flux (0.42m/d) could be maintained for about three months by regular air backwashing of $70g/m^2$ filter at 0.3m water head. The removal efficiency of organic matter by the system was BOD 93.3%, CODcr 96.3%, SS 96.7%. The effluent quality was 7.8mg/L, 12mg/L and 5mg/L for BOD, CODcr and SS, respectively. The water quality was enough to meet a standard for domestic reuse without human contact. T-N removal efficiency was 49.9% at internal recycle rate 2Q and C/N ratio 3.3. The removal efficiency of T-P was 50% with average effluent concentration, 2.6mg/L.

• Journal of Korean Society for Atmospheric Environment
• /
• v.8 no.1
• /
• pp.68-73
• /
• 1992

A study on the formation of particulate nitrate$(NO_3^-)$ and gaseous nitrate$(HNO_3)$ in the atmosphere was carried out in Seoul from Oct 8 to 11 1991. To collect $NO_3^-$ and $HNO_3$ in the ambient air, dual filter pack sampler (47mm$\phi$) was used. In the dual filter pack sampler, the first filter was Teflon filter (poresize 1$\mum$) for collection of $NO_3^-$ and the second filter was Nylon filter (poresize 0.45 $\mum$) for $HNO_3$. Particulate nitrate$(NO_3^-)$ and Sulfate ions were analysed by Ion chromatography. $HNO_3$ concentration was higher in the day time $(9.93\mug/m^3)$ than the night time$(3.50\mug/m^3)$, and Particulate nitrate$(NO_3^-)$ concentration was higher in the night time and early morning$(6.21\mug/m^3)$ than the day time$(4.31\mug/m^3)$. The conversion rate of $NO_x$ to total nitrate$(NO_3^-, HNO_3)$ was 7.57%/hr in the day time and 4.79%/hr in the night time, and total average conversion rate was 5.60%/hr.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.57 no.3
• /
• pp.255-259
• /
• 2008

In this paper, a current-mode integrator for low-voltage, low-power analog integrated circuits is presented. Using the proposed current-mode integrator, the baseband analog filter is designed for WCDMA wireless communication. To verify the proposed current-mode integrator circuit, Hspice simulation using 1.8V TSMC $0.18{\mu}m$ CMOS parameter is performed and achieved 44.9dB gain, 15.7MHz unity gain frequency. The described 3rd-order current-mode baseband analog filter is composed of the proposed current-mode integrator, and SFG(Signal Flow Graph) method is used to realize the baseband filter. The simulated results show 2.12MHz cutoff frequency which is suitable for WCDMA baseband block.

• The Journal of Information Technology
• /
• v.9 no.1
• /
• pp.33-39
• /
• 2006

This study is for the contents of development to the hardware system and software driving algorithm to implement the frequency band of about 7KHz los pass digital filter which has the cut-off frequency of 392Hz by interfacing of a microprocessor with its peripheral analog-to-digital converter chip and digital-to-analog converter chip. The simplicity of digital filter design without difficulty and the implementation of programmed digital filter can be realized by providing the interfacing method to implement the law pass digital filter for the biological signals and the realization method of computer algorithm by a microprocessor.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.58 no.3
• /
• pp.316-322
• /
• 2009

This paper presents an analytical design method of a passive harmonic filter for a three-phase diode rectifier and uses a new transfer function approach in the analysis and design. The transfer function approach derives an analytical formulation of an utility system including passive filters with a basis of Laplace transform and provides a graphical formulation so that a visualized insight into an interaction between individual filter and system response can be attainted. Harmonic impedance, voltage division and current division transfer function are used as a design tool, which makes a calculated filter parameters to satisfy IEEE-519 distortion limits. A simple five-step design procedure is introduced in the filter design, which consists of system analysis, selection of PCC(Point of Common Coupling), filter specification calculation, appropriate filter design for system and filter implementation. Philosophy governing the design procedure is based on a numerical/graphical iterative solution, trial and error with visualization feed-back based on "algebra on the graph". Finally, performance of the designed passive harmonic filter is verified by experiment and shows that 5th, 7th, 9th, 11th and 13th harmonics are decreased within IEEE-519 distortion limits, respectively.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.29 no.3
• /
• pp.151-158
• /
• 2018

This paper proposes a new design method for narrow bandpass filters using two cascaded hairpin step impedance resonators (SIRs) with wideband harmonic suppression. The proposed bandpass filter utilizes a suspended strip line (SSL) to maximize the characteristic impedance ratio, thereby maximizing the harmonic suppression bandwidth. As an example of the proposed design method, the SSL bandpass filter with a center frequency of $f_0=1.4GHz$ and fractional bandwidth of 5 % was implemented, and proved to suppress harmonics up to $7.5f_0$ with a passband insertion loss of approximately -0.9 dB. This result implies that the proposed SSL narrow bandpass filter (NBPF) can suppress the harmonic bandwidth more than two times as compared with the filter design on a microstrip line (MSL).

• Journal of Korean Society of Environmental Engineers
• /
• v.39 no.1
• /
• pp.19-25
• /
• 2017

In this study, a electrostatic filter which could be applicable to road environment was developed and evaluated in adsorption capacity. The evaluation were performance for removal by particle size and adsorption amount by pressure using ASERAE 52.1 and 52.2. The range of size for removal test was $0.3{\mu}m{\sim}10.0{\mu}m$ which had 12 steps. The filter showed 91.3% removal efficiency from $2.5{\mu}m$ and under the size, average 53.5% proportional to decreasing size value. The weight removal was 96.7% from 22.6 mmaq, initial pressure to 35 mmaq, end pressure with $715.9g/m^2$, the adsorption amount. The shape of isotherm was expressed as Langmuir's one. After washing saturated filter with dust to end pressure, the initial pressure and adsorption amount of the filter showed a light drop with no removal efficiency decline.

• 한국초전도학회:학술대회논문집
• /
• v.10
• /
• pp.193-196
• /
• 2000

A new type low-pass filter design method based on a coupled line and transmission line theory is proposed to suppress harmonics by attenuation poles in the stop band. The design formula are derived using the equivalent circuit of a coupled transmission line. The new low-pass filter structure is shown to have attractive properties such as compact size, wide stop band range and low insertion loss. The seventh-order low-pass filter designed by present method has a cutoff frequency of 0.9 CHz with a 0.01 dB ripple level. The coupled line type low-pass filter with strip line configuration was fabricated by using a high-temperature superconducting (HTS : YBa$_2$Cu$_3$O$_{7-{\delta}}$ thin film on MgO(100) substrate. Since the HTS coupled tine type low-pass filter was proposed with five attenuation poles in stop band such as 1.8, 2.5, 4, 5.5, 6.2 GHz. The fabricated low-pass filter has improved the attenuation characteristics up to seven times of the cutoff frequency.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.13 no.7
• /
• pp.1267-1271
• /
• 2009

In this paper, a diplexer circuit to separate GSM from CDMA band is designed using a LTCC (Low Temperature Cofired Ceramic) multi-layer technology. In order to increase a integration capability of the diplexer, it is designed using 3-dimensional (3-D) multi-layer compact inductor and capacitors in e-layer LTCC substrate with a relative dielectric constant of 7. In order to achieve high selectivity of the bands, a shunt capacitor and inductor are designed in the high-pass filter (HPF) and low-pass filter (LPF), respectively. The size of the fabricated diplexer including CPW pads is 3,450 ${\times}$4,000 ${\times}$694 ${\mu}m^3$An insertion loss (IL) and return loss in GSM band are less than -1.35dB and more than -5.66dB,respectively. In the case of CDMA band, the IL of -1.54dBandRLof above -9.30dBare archived.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.9 no.3
• /
• pp.602-608
• /
• 2005

We have studied to obtain the SAW filter for the Single Phase Unidirectional Transduce. (SPUDT), was formed on the Langasite substrate and was evaporated by Aluminum-Copper alloy and then we performed computer-simulated by simulator. We can fabricate that the block weighted type IDT as an input transducer of the filter and the withdrawal weighted type IDT as an output transducer of the filter from the results of our computer-simulations. Also, we have performed to obtain the properly conditions about impedance matching of the SAW filter for SPUDT. We have employed that the number of pairs of the input and output IDT are 50 pairs and the thickness and the width of reflector are 5000A and $3.6{\mu}m$, respectively. And the width of IDT' fingers is $2.4{\mu}m$, and the space between IDT' finger and reflector is $2.0{\mu}m$. Frequency response of the fabricated SAW filter has the property that the center frequency is about 190MHz and bandwidth at the 3dB is probably 7.7MHz after when we have matched impedance. Also, we could obtain that ripple characteristics is less than 0.4dB and standing wave ratio is probably 1.5 after when we have matched impedance.