This study was peformed to establish the standard size system to be required for the production of brassiere. The subject were 155 Korean twenties-aged women and were directly measured anthropometrically. From 27 measurements, 5 factors were extracted through factor analysis. The accumulative contribution ratio is 76.92%. Factor 1 indicates the degree of obesity around the chest, factor 2 is the drooping degree of breast, factor 3 is the contours and prominence, factor 4 is the breast breadth and breadth of bust point, factors 5 is the volume of breast. The subject were classified into 3 cluster as their breast types through cluster analysis. Type 1 is the closest to the ideal breast shape and not too droopy. This group belonged to 75A. Type 2 has small breast and belonged to 70AA group. Type 3 is the obesest and has the biggest and droopy breast. This group belonged to 75B. The distribution of size of brassiere had 3 sections from 70 to 80 showing a rate of 81.94% and the sin of the cup had 4 sections from AAA cup to B cup showing a rate of 89.70%. The production ratio of each brassiere size, it was found that the brassiere size of highest production ratio was 75A(16.39%) in type 1,70AA(16.27%) in type 2, and 75B(13.72%) in type 3. This suggests that it is necessary to adjust for the production rate of brassieres.
Journal of the Korean Society of Clothing and Textiles
/
v.25
no.4
/
pp.719-730
/
2001
The purpose of this study is to develop the basic patterns of adult womens brassiere therewith, provide for some basic data useful to the brassiere manufacturing which are both functional and fitting. For this purpose, 220 adults women(aged between 20 and 59) were sampled to be measured for their body sizes and tested for their brassiere wearing. The collected data were statistically processed using the SAS 6.12 for Means, Standard Deviation, etc. The results of this study can be summarized as follows; 1. In order to develop the basic patterns of adult womens brassieres, 75A size was selected out of 12 size combination(3 women per 75A size) and then, their brassiere fitting was tested. As a result, the fronts of the basic patterns were found to have such problems as undone front center, poor levelling of upper cups bottom line or lower cups top line, poor shape of upper cups outside top line and shoulder strip position. On the other hand, n the rear side of the basic patterns, the central part of the wing was slightly lifted, while the wing width and straps interval did not befit the full-cup brassiere. The result of this first brassiere fitting test showed that the functionality and aesthetics of the basic pattern brassieres were more or less satisfactory, and thus, the problems were address for the second test. In the second test, the aesthetics, breast-shaping effect and functionality of the basic pattern brassieres were much improved. 2. The basic patterns of adult womens brassieres were characterized by a round cup wired as well as a full cup embracing the entire breasts. Each basic pattern which consisted of upper and lower cups was shaped \"straight(-)\". The basic sizes adopted at the first design stage (see fig. 1-2) was 75A of which was designed as upper foundation basic pattern. At the second stage, the upper body foundation pattern were used to design lower cup, upper cup, front panel and wing in their order.(see fig. 3-5, fig. 8)5, fig. 8)
The purpose of this study is to dvelop the basic pattern of wome which are fitting for 75A. The collected data were statistcally processed usig the SPSS 10.0 for Mans Standard Deiation, Cronbach's $\alpha$, etc. This study suggested a size chart for body measurement for constructing basic brssiere patterns with size of 75A. The construction of this experimental brassiere were lower cup, upper cup, front panel and wing and characterized by a round cup wired as well as a full cup embrcing the entire breasts. The drafting method for constructing basic brassiere patterns for 75A was completed by selecting a total of 11subjects, and two wearing tests were carried out with the subjects. the dimensions and shapes of the basic brassiere pattern suggested in this research proved to be fitting and to have a wearing effect that brings together and supports the breasts.
Journal of the Korea Academia-Industrial cooperation Society
/
v.21
no.6
/
pp.672-678
/
2020
Ogive parts of large-caliber ammunition in Korea are manufactured by the Press Nosing method, but this method has the disadvantage of requiring additional processes such as lubrication before and after the press process. This study proposes the possibility of applying the Swaging method to improve these shortcomings. A large-diameter shell body was manufactured in sub-scale and plastic working experiments using a swaging process were performed. We investigated whether plastic processing is possible up to 75 % of the diameter reduction rate that satisfies the final molding dimension, and whether the dimensions of the product produced by swaging molding are satisfactory as the hardness changes according to the diameter reduction rate and the increase in thickness. The test using the prototype confirmed that the hardness increased proportionally with the diameter reduction rate and by more than HV 335 at the reduction rate of 75 %. The material thickness variation tended to be similar to the theoretical calculated value, and the thickness increase rate was proportional to 65.4 % at the reduction rate of 75 %.
We investigated the vegetation structure, and effects of canopy degree(gap or purlieu to 25%, 50%, 75%, over 75%) of the overstory on seedling regeneration and survivorship, and sapling density, growth and growth type of Abies koreana in subalpine of Mt. Chiri. The stem density in Abies koreana stand was higher in middle story than upper story, individual trees in upper story occupied larger area and were more apart, resulted in uniform distribution. The regeneration and survivorship of seedlings and saplings were best in 25% of crown closure, in order of 50%, gap, but lowest in over 75% of crown closure. The annual growth rate and recent 5 years growth rate of saplings were highest in gap or purlieu and getting lower toward gradually higher coverage of overstory. And 10- to 20-Year-old saplings were mainly regenerated in stands with lower density(I or II), but most of 20 to 30 years old saplings were growing in stands with higher density (III or IV). The number of "A" type saplings grown normally in gap or purlieu was gradually decreased in stand with higher density but the number of "D" or "E" types of which growth was supressed or prohibited by the high density was abruptly increased. Saplings normally growing in the gap and purlieu showed the panicle type, but those grown under dense crown were greatly suppressed and showed the umbellate type.
Journal of the Korean Society of Clothing and Textiles
/
v.26
no.6
/
pp.821-832
/
2002
The purpose of this study was to develop grading method of the basic brassiere patterns therewith, provide for 12 size's brassiere patterns and prove fitness of their's and shape. The collected data were statistically processed using the SAS 6.12 for Means, Standard Deviation, etc. The results of this study can be summarized as follows; 1. The basic sizes adopted at the first design stage (see fig.1-2) were 75AA, 75A and 75B each of which was designed as upper foundation basic pattern in reference to the cup size. At the second stage, each of the upper body foundation basic pattern was used to design lower cup, upper up, front panel and wing in their order(see fig.3-6). At the third stage, the other sizes were graded in reference to the three brassiere patterns (75AA, 75A and 75B) to produce 12 brassiere sizes(see Tab. 7-8). In order to develop the basic patterns of adult women's brassieres, 33 women were selected per 11 size combination(3 women per size combination), and then, their brassiere fitting was teated. As a result, the fronts of the basic patterns were found to have such problems as undone front center, poor levelling of upper cup's bottom line or lower cup's top line, poor shape of upper cup's outside top line and shoulder strip position. On the other hand, on the rear side of the basic patterns, the central part of the wing was slightly lifted, while the wing width and straps'interval did not befit the ful1-cup brassiere. The result of this first brassiere fitting test showed that the functionality and aesthetics of the basic pattern brassieres were more or less satisfactory, and thus, the problems were addressed for the second teat. In the second test, the aesthetics, breast-shaping effect and functionality of the basic pattern brassieres were much improved. 2. We were to present the final brassiere sizing system to extend the interior length of breast and the exterior length of breast on the basis of fitting test. Thereby, 75B$.$80A$.$80B$.$85A$.$85B's the interior lengths of breast were enlarged to 0.7cm, the rest size was enlarged to 0.5cm and the exterior length of breast was enlarged to 0.5cm regardless of sizes. 3. The upper foundation basic patterns of 75AA and 75B were presented and and the basic brassiere pattern and grading pattern were presented through to.
The fresh-water shrimp, Macrobrachium nipponensis (DE HAAN) is one of the largest of the shrimp species and one of the most important types fo protein food in fresh water fisheries. It can be found from Cheju island in the touth to Chung-ju in river or swamp, in the north. The breeding of these shrimps was studied by Chun and Yu (1967) and the relative growth was reported by author (1970a), but they did'nt provide other ecological features widely found in their natural environment. Shrimps were collected from the Nak Dong River, near Pusan, Korea once a month, from March to December 1963. The following is a summary of the results. 1. Larvae hatch from May to September, mainly in the month of July. 2. The average sex ratio ($male/female{\times}100$) is $62.9\%$ and goes down during the spawning season and rises from fall to spring season. 3. The minimum size of the female with eggs is aproximately 4.2cm in body length 3.5 gr in body weight, and 1.5 cm in carapace length. 4. Most shrimps of 5.75-7.75 cm in body length lay eggs. 5. The dorsal spines of the rostrum are 10-16(mode13) in number and the ventral spines of the rostrum are 1-5 (mode 3) in number.
We conducted a thermal compression of domestic Korean pinewood for a use in flooring. For the evaluation of flooring material, we measured dimensional stability and surface hardness of thermally compressed wood. It is possible to make high-specific gravity woods with a range of 0.82-0.92 after the thermal compression with 50% compression set. The surface hardness increased with an increase in the pressing temperature. The highest value of surface hardness was $23.6N/mm^2$, which was obtained from the thermal compressed wood with pressing temperature of $160^{\circ}C$ and 30 minutes of pressing time. However, the surface hardness of woods treated at high temperature of $180^{\circ}C$ or greater decreased. The recovery of thickness decreased with increasing the pressing temperature. For dimensional stability, compression temperature was more dominant than compression time.
The sectional dimensions and initial crookedness of the RHS(rectangular hollow section, ${\boxe}-75{\times}75{\times}3.2,\;{\boxe}-100{\times}100{\times}4.2,\;{\boxe}-125{\times}125{\times}6.0$) were measured. The axial compressive strength tests for columns with slenderness $46{\sim}84$ were performed as well as stub tests and tensile tests. FEM analysis was also used. The measurement shows that the errors of sectional dimensions are negligible. For the column length corresponding to ${\lambda}=100$, the initial crookedness with the 2.5% probability estimated from the measured results is 1/490, 1/1121 1/1395 for each section respectively. The yield strengths obtained from tensile test are higher than the specified minimum value by more than 30%. The column test shows that the maximum axial resistances are almost same as, or a little higher than the FEM results and the specified strength curves of AISC Specification and Eurocode, when the maximum strengths from the stub tests are used as the yield strength of the steel. But the test results show much higher column strength than those specified in the Standard and Code, when the specified minimum yield strength of the steel is used.
PURPOSES : This study primarily focused on evaluating the performance characteristics of 4.75-mm nominal maximum aggregate size (NMAS) asphalt mixtures for their more effective implementation to a layered flexible pavement system. METHODS : The full-scale pavements in the FDOT's accelerated pavement testing (APT) program, including 4.75-mm mixtures at the top with different thicknesses and asphalt binder types, were considered for the faster and more realistic evaluation of the rutting performance. The results of superpave indirect tensile (IDT) tests and hot-mix asphalt fracture mechanics (HMA-FM) based model predictions were used for cracking performance assessments. RESULTS : The results indicated that the rutting performance of pavement structures with 4.75-mm mixtures may not be as good as to those with the typical 12.5-mm mixtures, and pavement rutting was primarily confined to the top layer of 4.75-mm mixtures. This was likely due to the relatively higher mixture instability and lower shear resistance compared to 12.5-mm mixtures. The energy ratio (ER) and HMA-FM based model performance prediction results showed a potential benefit of 4.75-mm mixtures in enhanced cracking resistance. CONCLUSIONS : In relation to their implementation, the best use of 4.75-mm mixtures seem to be as a surface course for low-traffic-volume applications. These mixtures can also be properly used as a preservation treatment that does not necessarily last as long as 12.5-mm NMAS structural mixes. It is recommended that adequate thicknesses and binder types be considered for the proper application of a 4.75-mm mixture in asphalt pavements to effectively resist both rutting and cracking.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.