• Journal of Environmental Health Sciences
• /
• v.22 no.3
• /
• pp.116-122
• /
• 1996

This study has been focused on the applicability of microwave treatment of soil contaminated by volitile organic chemicals. Substrates studied were sand and sandy soil. These substrates were impregnated with toluene, tetrachloroethylene, o-xylene and p-dichlorobenzene. The microwave treatment was conducted in a modified domestic microwave oven: 2450 MHz, 700 W. The sandy soil temperature added water went up rapidly to about 130$\circ$C for 4 minutes. And then, the temperature appeared to plateau out. A series of tests were performed to depict the effectiveness of microwave treatment technique to organic contaminants from soils. Removal efficiencies in sandy soil and sand were increased with increasing water content and exposure time. Microwave radiation penetrates the soil and heats water throughout the matrix. Therefore, addition of a certain amount of water to the contaminated soil can efficiently enhance the ability of the soil to absorb microwave energy and promote the evaporation of the volitile contaminants. And the vapour pressure of impregnated organic contaminants becomes lower. the removal efficiency becomes poor.

• Fibers and Polymers
• /
• v.4 no.4
• /
• pp.204-209
• /
• 2003

The effect of padding solution on the microwave heat dyeing of polyester fabric was studied extensively. Polyester fabrics were impregnated in aqueous urea solution and aqueous sodium chloride solution for 10 min and then dyed for 7 min by microwave apparatus (2450 MHz, 700 W) under optimum conditions which provide good exhaustion. Aqueous solutions of urea and sodium chloride showed more effective than water as a padding solution for microwave heat dyeing. The type of solvent added in padding media and its concentration significantly affects the K/S values of dyed polyester fabric. Added solvents such as n-hexane, acetone, and dimethyl formamide were also more effective than 100 % water as padding media for the microwave heat dyeing. It is supposed that the effect of used solvents on dyeing property of polyester fabrics depends on the solubility parameter difference between solvent and polyester fabric.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.08a
• /
• pp.94-97
• /
• 2003

This study uses ZnO thin film as a piezoelectric material and Pt as bottom electrode for FBAR (film bulk acoustic resonator) device. ZnO thin film and Pt were deposited by RF-magnetron sputtering method. ZnO thin film and Pt were oriented to c-axis. Top electrode Al was deposited by thermal evaporation. The membrane was formed of bulk micromachining. The FBAR was evaluated by XRD, SEM and electrical characterization. The resonant frequency was measured by HP 8753C Network Analyzer. A fabricated FBAR device exhibited a resonant frequency of 700 MHz ~ 1.5 GHz. When bottom electrode and top electrode thickness were fixed, the resonant frequency was increased as decreasing ZnO thin film thickness.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.28 no.3
• /
• pp.566-571
• /
• 1999

Effects of storage temperature at 18oC and 5oC for 9 days and heating conditions on textural char acteristics in strong wheat flour gels were investigated using a Instron after microwave (2450MHz, 700W). Heating condition did not affect the texture property in the wheat flour gels, but the frozen storage was very effective to prevent the hardening of the samples. Hardness, adhesiveness, and gumminess in the wheat flour gels decreased in increasing moisture content from 45% to 55%, but there was little change in cohesiveness. The storage at room temperature for 2 hours resulted in increased hardness in the heated wheat flour gels. PE wrap package of the wheat flour gels prevented weight loss by 3~6% and hardening effectively. Sugar, or sugar and shotening resulted in increased hardness in loaf bread. The hardness and weight loss in loaf breads were markedly changed by the heating time with microwave. The most critical time point was around 4 minutes following the heating.

• Textile Coloration and Finishing
• /
• v.11 no.3
• /
• pp.49-57
• /
• 1999

The effect of padding solution for the microwave heat dyeing of polyester fabric was studied variously. The dyeing property of polyester fabric varied with the kinds of added chemicals in the padding solution. Polyester fabrics impregnated in aqueous urea solution and aqueous sodium chloride solution for 10 minutes and then dyed for 7 minutes by microwave apparatus(2450 MHz, 700 W) under optimum conditions give good exhaustion. An aqueous solution of urea and a sodium chloride solution was more effective than water as padding solution for microwave heating dyeing. The K/S values of dyed polyester fabric by microwave were significantly affected by the type of solvent added in padding media and its concentration. Added solvents, n-hexane, acetone and dimethyl formamide were also more effective than water as padding media for the microwave heating dyeing. It is assumed that the effect of used solvents on dyeing property of polyester fabrics depends on the solubility parameter difference between solvent and polyester fabric.

• Proceedings of the Korea Information Processing Society Conference
• /
• 2015.04a
• /
• pp.1005-1007
• /
• 2015

사물 인터넷(Internet of Things)의 확산으로 가까운 미래에는 사물 인터넷 환경에서 질의 응답 시스템이 활발하게 이용될 것으로 예상된다. 본 논문에서는 사물 인터넷 환경에 적합한 초소형, 저사양 하드웨어를 이용하여 커뮤니티 질의 응답 시스템(Community Question Answering System)을 구축하는 방안에 대해 살펴본다. 하드웨어는 700Mhz 싱글 코어 CPU와 512MB의 메인 메모리를 장착한 라즈베리 파이를 이용하였고, 질의 응답 시스템으로는 Apache Solr를 기본 시스템으로 활용하였다. 성능 분석 결과 실시간 응답성은 매우 훌륭하지만 정확도는 앞으로 보완이 필요한 것으로 분석되었다.

• Progress in Superconductivity and Cryogenics
• /
• v.10 no.2
• /
• pp.27-29
• /
• 2008

Superconducting RF cavities are being considered for accelerating a proton beam at 700 MHz in the linac of the Proton Engineering Frontier Project (PEFP) and its post-project. Dumbbell fabrication is a mid-process for manufacturing an elliptical superconducting RF cavity. During the dumbbell fabrication, control of the dumbbell length and the $TM010\;{\pi}$ mode frequencies is necessary to build up a desired cavity. A new formula with a perturbation measurement method is used to measure and calculate the frequencies of the individual half-cells of a PEFP low-beta dumbbell, and to tune the frequency and length of the half-cells. In this article, the tuning method and results of the PEFP low-beta dumbbells have been presented.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.20 no.8
• /
• pp.694-700
• /
• 2009

In this paper, we propose a RFID tag antenna with low performance degradation due to nearby dielectric materials. The proposed antenna is designed to be appropriate for ink printing fabrication. The antenna is designed to operate in UHF band of $860{\sim}960$ MHz. The antenna uses a T-matching network in the middle of the main body and two parasitic patches in vicinity for complex conjugate matching with a commercial tag chip. In addition, the two parasitic patches induce currents at different dielectric constants of nearby dielectric materials. This can minimize the performance degradation due to nearby dielectric materials. The measured results show the half power matching bandwidth from 844 MHT to 1,268 MHz. It exhibits the reading distance of about 3.5 m in free space when the tag antenna is used with the commercial reader antenna (transmitting power of 20 dBm and the reader antenna gain of 6 dBi). When the tag is attached on dielectric materials of wood and FR4, the resulting reading distances are 2.61 m and 2.51 m, respectively.

• Journal of the Korean Magnetics Society
• /
• v.13 no.1
• /
• pp.6-14
• /
• 2003

The purpose of this study is to investigate the effect of chemical reaction with a bonding glass on physical and magnetic properties of Fe-Hf-N/SiO$_2$ and Fe-Hf-N/Cr/SiO$_2$ thin films. When the Fe-Hf-N/SiO$_2$ films were reacted with the bonding glass, the soft magnetic properties of them were extremely degraded. At $600^{\circ}C$, the saturation magnetization of the reacted film decreased to 1 kG, and its coercivity increased to 27 Oe, and its effective permeability decreased to 70. It was found that the degradation of soft magnetic properties of the Fe-Hf-N/SiO$_2$ films reacted with the bonding glass were attributed to the oxidation of the Fe-Hf-N layers to HfO$_2$ and Fe$_3$O$_4$. The soft magnetic properties of the Fe-Hf-N/Cr/SiO$_2$ films reacted with the bonding glass were degraded less than those of Fe-Hf-N/SiO$_2$ films. At $600^{\circ}C$, the saturation magnetization of the reacted film decreased to 13.5 kG, and its coercivity increased to 4 Oe, and its effective permeability decreased to 700. It was found that the Cr layer suppressed the oxidation of the Fe-Hf-N layers during the chemical reaction between the Fe-Hf-N layer and bonding glass.

• Journal of Korean Society of Environmental Engineers
• /
• v.29 no.3
• /
• pp.304-310
• /
• 2007

The purpose of this research was to investigate the effects of the co-treatment of municipal wastewater with microwave-irradiated excess sludge on the treatment efficiency and excess sludge production of the activated sludge process. When 250 mL of excess sludge with a MLSS concentration of approximately 2,000 mg/L was microwave-irradiated at $20^{\circ}C$ for $40\sim300$ sec by a microwave oven (2,450 MHz, 700 W), the temperature of the sludge increased at a rate of approximately $20^{\circ}C/min$ and the SCOD, TKN and T-P concentrations of the sludge showed the highest increase in the irradiation time of $40\sim130$ sec. And, the oxygen uptake rate measurement of the sludge microorganism suggested most of the microorganisms in the sludge were destroyed at an irradiation time above 130 sec(above $65^{\circ}C$). When the municipal wastewater and microwave-irradiated excess sludge was co-treated by the activated sludge process, almost no effect was observed in the pH and alkalinity of both the influent and effluent, but the influent concentrations of SS, COD, T-N and T-P increased. Even though the effluent SS, BOD and T-P concentrations showed almost no effect, the COD and TKN concentrations increased. The microbial yield coefficient decreased at a rate of 0.91 g SS/g COD removed as the irradiation ratio increased at a rate of 1 g SS/g SS-day.