• 제목/요약/키워드: 5D CAD

검색결과 275건 처리시간 0.023초

${\Omega}$/PC 그래픽 보오드를 이용한 집적회로 설계용 레이아웃 에디터의 개발 (Development of a Layout Editor for Integrated Circuit Design Using ${\Omega}$/PC Graphics Board)

  • 정갑중;장기동;정호선;이우일
    • 대한전자공학회논문지
    • /
    • 제26권5호
    • /
    • pp.99-107
    • /
    • 1989
  • 본 논문에서는 IC Mask Layout을 위한 2차원 그래픽스 에디터 KUIC_LED(kyungpook national university intelligent CAD_layout editor)를 개발하였다. KUIC_LED는 ${\Omega}$/PC/AT상에서 동작하고 Layout에 필요한 60여가지의 다양한 기능들을 제공한다. 본 시스템은 C Language와 Assembly Language로 작성 되었다.

  • PDF

Isolation 특성이 좋은 Orthogonal Mode Transducer 설계와 제작 (Design and Fabrication of a Simple Orthogonal Mode Transduce with Good Iolation)

  • 오이석;이진원;홍진영
    • 한국전자파학회논문지
    • /
    • 제11권6호
    • /
    • pp.914-919
    • /
    • 2000
  • 이 논문에서는 Z-밴드용 간단한 구조의 OMT (orthogonal mode transducer)가 소개되다. 이 OMT는 몇 개의 가는 유도 봉을 이용하여 한 편파를 주어진 방향으로 유도하고. 또한 다른 직각 편파를 유도 봉을 이용하여 다른 방향으로 유도하도록 설계되었다. 이 OMT는 유도 봉들이 있는 T자 형태의 도파관 부분과 두 도파관 연결부분으로 구성되어 있고, 한 안테나와 두 개의 어댑터들과 연결되도록 세 플랜지를 갖고 있다. 유도 봉의 최적개수와 최적 위치는 CAD인 HFSS를 이용하여 수치적으로 얻었다. 제작된 OMT에서 두 폄파간의 isolation은 9.5GHz와 10.5GHz 주파수 밴드에서 42.8dB보다 높았으며, 반사계수는 -17.5dB보다 낮았다. 이 OMT는 polarimetric scatterometer 시스템에 사용되는 polarimetric 안테나에 사용되어질 수 있다.

  • PDF

패턴의 Block화(化)에 의(依)한 어패럴 CAD System의 활용(活用) (Practical Use of Apparel CAD System by the Classification of Basic Pattern Block)

  • 이형숙;김옥경
    • 한국의류학회지
    • /
    • 제17권3호
    • /
    • pp.391-406
    • /
    • 1993
  • The purpose of this study was to utilize of apparel CAD System by the classification of the basic pattern block in pattern making process. Gerber AM-300 CAD System was used for this study. The results form this study were as follows; 1. New shirts block were developed. 2. The sensory test was applied to evaluate the new shirts block for women by comparing it with Japanese Bunka shirts blouse pattern making method. According to a statistical analysis of the result of the 20 items on the questionnaire, the 19 items showed significant difference(${\alpha}{\leq}0.01$)between the two, with the new shirts block having higher scores. 3. A basic pattern block was selected by the design sketch. 4. P/D/S were enabled to be constructed directly from a block pattern. The drawing, deletion. duplication, and movement of all points and lines in the pattern might be made freely, and the split, pivot, and movement of the pattern, and the attachment of two patterns were possible. 5. Automatic grading of finished pattern have been developed by creation and modification of grading rules of block pattern.

  • PDF

변분법에 의한 마이크로파 E-평면 여파기와 Unilateral Fin-Line 여파기의 해석 및 CAD 설계 (analysis and computer-Aided Design of Microwave E-plane Filter and Unilateral fin-Line Filter by Variational Method)

  • 임재붕;이충웅
    • 대한전자공학회논문지
    • /
    • 제22권6호
    • /
    • pp.63-70
    • /
    • 1985
  • Unilateral Fin-Line 구조와 I-평면 구조를 Rayleigh-Ritt의 변분법으로 해석하는 방법을 제시하고, Cohn의 여파기 설계 이론에 의해 대역통과 멸파기를 설계하는 CAD프로그램을 개각했다. 관내 재역폭이 5%∼24.6%인 Unilateral Fin-Line 여파기를 제작하여 수험과 이론이 일치함을보였다. 시험 결과, 삽입손실이 0.17∼0.2545의 저손실 여파특성을 얻었으며 중심주파교에 대한 오차는 0.2%이 내였다.

  • PDF

3차원 인체 스캔 데이터를 활용한 Hip-hugger 의류용 벨트 패턴 설계 (Belt Pattern Making for Hip-hugger garment using 3D Body Scan Data)

  • 박순지;최신애
    • 한국의류산업학회지
    • /
    • 제10권5호
    • /
    • pp.652-659
    • /
    • 2008
  • This study was designed to testify the possibility and devise the method to manipulate the 3D body scan data to produce rounded-belt pattern adaptable to hip-type variation of women in their 20's. The results of this research were as follows : Firstly, based on drop-value distribution of hip and waist girth, 151 subjects were classified into three hip-types; Type 1 (15.23%) was 'cylinder type', showing lowest drop-value, Type 2 (69.54%) was 'average type' and Type3 (15.23%) was 'hourglass type' showing highest drop-value. Secondly, using CAD program, design lines for round shape belt were set on the surface of 3D scan data of representative subject of each type. And divided 3D surfaces were flattened onto the plane by the internal tools of CAD program. The measure, 'lifting value of round belt pattern', implying the level of curve ratio of pattern was higher in back than front. This result might be linked to the fact that the hip part is more protruded than the abdomen part. And the measures also showed highest values in Type 3(hourglass type) and lowest in Type 1(cylinder type), meaning that the pattern of Type 3 showed more rounded shape than that of Type 1. This finding implied that round belt for body type having high drop-value should be shaped more curved. Thirdly, difference ratios of outline length and area between 3D curves(body surface) and 2D plane(pattern) were 4.5% and 1.3%, respectively. This result demonstrated and solidified the feasibility of designing digital garment pattern from 3D body scan data.

자동차 보닛금형의 자동설계 지원시스템에 관한 연구 (A Study on the Automatic Design Supporting for Automobile Bonnet Tools)

  • 정효상
    • 한국정밀공학회지
    • /
    • 제21권5호
    • /
    • pp.131-141
    • /
    • 2004
  • In this study a 3-D automatic die design supporting system for a bonnet panel has been developed using Pro/ROGRAM of the widespread CAD software Pro/ENGINEER A standard drawing die was defined in terms of the punch profile, the die face geometry, and the blank sheet size. The strip layout of a trimming die was defined, in addition, in terms of the trimming line and the locations of scrap cutters. Necessary relations for each design step are formulated and rules for bottom-up type 3-D die design were set up for the automatic design of drawing and trimming dies of a bonnet. With the input geometric data of punch profile, die face, and blank sheet, this 3-D design supporting system could complete the basic design process, in case of the bonnet drawing die, in a time 78% shorter than that required by a typical 2-D CAD system. The new design system showed remarkable design efficiency also when it was applied to the case of redesign and modification of the previous standard output for a different car type.

배추의 생육초기에 복숭아혹진딧물의 경제적 피해수준 설정 (Economic Injury Level of Myzus persicae (Homoptera: Aphididae) at Chinese Cabbage)

  • 전흥용;강택준;김형환;양창열;김동순
    • 한국응용곤충학회지
    • /
    • 제47권4호
    • /
    • pp.407-411
    • /
    • 2008
  • 봄 배추 생육초기에 복숭아혹진딧물의 접종밀도에 따른 진딧물의 밀도 증가가 배추의 수량에 미치는 영향을 조사하여 경제적 피해수준과 요방제 수준을 설정하고자 하였다. 복숭아혹진딧물을 배추정식 후 10일에 포기당 2, 5, 10, 15 및 20마리 접종한 경우 접종 후 18일의 복숭아혹진딧물의 밀도는 각각 92.3, 177.4, 406.9, 440.4, 471.3마리로 증가하였으며, 배추의 생체중은 복숭아혹진딧물의 무처리, 2, 5, 10, 15 및 20마리 접종구에서 각각 602.0, 264.2, 262.0, 109.3, 151.0, 67.3 g으로 접종밀도가 높을수록 배추의 생체중은 현저하게 감소하였다. 복숭아혹진딧물의 발생밀도와 배추의 생체중과의 관계를 구명하기 위하여 진딧물의 누적발생일수(cumulative aphid days)와 배추 생체중과의 관계식을 구한 결과 비선형의 대수모형에 잘 적용되었다. 이 관계식에서 경험적인 수익한계(gain threshold) 5%와 봄 배추 상품율(92%)을 감안하여 복숭아혹진딧물 5마리가 5일 동안 흡즙하여 13%의 수량감소를 유발시킨 경제적 피해수준을 추정한 결과 CAD 값이 25가 되었다. 또한 요방제밀도는 경제적 피해수준의 80%가 되는 CAD 값이 20으로 추정되었다. 따라서 본 결과는 봄 배추 생육초기에 복숭아혹진딧물의 요방제 밀도 설정에 유용하게 활용될 수 있을 것으로 여겨진다.

RF-SWITCH의 설계 및 제조에 관한 연구 (Study of Design and Fabrication on the RF-Switch)

  • 이재영
    • 마이크로전자및패키징학회지
    • /
    • 제5권2호
    • /
    • pp.49-52
    • /
    • 1998
  • 이동통신용 핵심 부품인 W-LAN용 RF-Switch를 설계 및 제작하였다. 본 연구에서 는 CAD를 이용한 전송선로 설계기술, 소형화, 다층화 설계기술, 이동통신용 MCM 부품의 패턴설계를 개발하였으며 RF-Switch 설계하는기법 소형화 및 다층화를 위한 MCM공법을 얻을수 있었다. Ant-Rx On시 삽입손실은 0.48dB로 나타났다.

Integrating 3D facial scanning in a digital workflow to CAD/CAM design and fabricate complete dentures for immediate total mouth rehabilitation

  • Hassan, Bassam;Greven, Marcus;Wismeijer, Daniel
    • The Journal of Advanced Prosthodontics
    • /
    • 제9권5호
    • /
    • pp.381-386
    • /
    • 2017
  • PURPOSE. To integrate extra-oral facial scanning information with CAD/CAM complete dentures to immediately rehabilitate terminal dentition. MATERIALS AND METHODS. Ten patients with terminal dentition scheduled for total extraction and immediate denture placement were recruited for this study. The patients were submitted to a facial scanning procedure using the in-office PritiMirror scanner with bite registration records in-situ. Definitive stone cast models and bite records were subsequently submitted to a lab scanning procedure using the lab scanner (iSeries DWOS; Dental Wings). The scanned models were used to create a virtual teeth setup of a complete denture. Using the intra-oral bite records as a reference, the virtual setup was incorporated in the facial scan thereby facilitating a virtual clinical evaluation (teeth try-in) phase. After applying necessary adjustments, the virtual setup was submitted to a CAM procedure where a 5-axis industrial milling machine (M7 CNC; Darton AG General) was used to fabricate a full-milled PMMA immediate provisional prosthesis. RESULTS. Total extractions were performed, the dentures were immediately inserted, and subjective clinical fit was evaluated. The immediate provisional prostheses were inserted and clinical fit, occlusion/articulation, and esthetics were subjectively assessed; the results were deemed satisfactory. All provisional prostheses remained three months in function with no notable technical complications. CONCLUSION. Ten patients with terminal dentition were treated using a complete digital approach to fabricate complete dentures using CAD/CAM technology. The proposed technique has the potential to accelerate the rehabilitation procedure starting from immediate denture to final implant-supported prosthesis leading to more predictable functional and aesthetics outcomes.

그림자 계산을 이용한 운전자의 시계성 해석 (Analysis of Driver's Field of View using a Shadow Algorithm)

  • 김재정;하용수;김용철
    • 한국자동차공학회논문집
    • /
    • 제5권5호
    • /
    • pp.123-131
    • /
    • 1997
  • To ensure drive's field of view, obstruction area generated by a steering wheel, hub and spoke must be considered at the early stage of automobile design. The current approach to computing obstruction area proposed by SAE is based on 2D drafting procedures so that it is not precise and errorprone. In the paper we discuss the novel approach which models the obstruction area as the shadows of the steering wheel, hub and spoke by assuming the human eye as light sources. The approach is based on ray tracing and space transformations for that it can be applied when free form curves are hired to represent the steering wheel, hub and spoke in CAD environment. As a result, it gives more predise and reliable results than SAE approach.

  • PDF