• Journal of Drive and Control
• /
• v.9 no.4
• /
• pp.52-57
• /
• 2012

In this study, in order to understand contents and ranges of design for the EGR Valve test system for improving quality and performance of EGR Valve, engine performance and exhaust gas characteristic of 3L-class diesel engine was analyzed. Experimental operation of engine performance test was performed with 50% engine load and 20% and 100% opening ratio of EGR Valve. From test of performance and exhaust gas characteristic of engine, torque output of engine and temperature and pressure of inlet and outlet of EGR Valve were measured. As a result, for design of EGR Valve test system, input fluid flow of EGR Valve must be set the same amount with exhaust gas flow that was below of engine speed of 2,500 rpm, and temperature of inlet of EGR Valve must be set under about $510^{\circ}C$. And the difference of temperature between inlet and outlet of EGR Valve must be over than about $200^{\circ}C$. Exhaust gas of inlet and outlet of EGR Valve were under 1 bar that was not considerable, and the difference of pressure between inlet and outlet of EGR Valve were under 1 bar that could not effect on mechanical operation of EGR Valve.

• The Journal of Korean Academy of Prosthodontics
• /
• v.38 no.4
• /
• pp.510-525
• /
• 2000

The effects of pretreatment of Co-Cr alloy, including two adhesive primers that contain either MDP or MAC-10, and silicoating on the bond The result sobtained as follows; o Strength of 4-META/MMA-TBB resin were investigated using FT-IR, SEM, and EDAX. o In the SEM observation of surface morphologies, the sandblasted specimen exibited a very rough surface, whereas the surfaces of the two groups primed with either MDP or MAC-10 were covered with a layer of primer, and the surface morphology of the silicoated specimen remained almost the same after sandblasting. o Before the thermocycling tests, the group treated with MDP demonstrated the highest mean tensile bond strength and the sandblasted group showed the lowest bond strength. o After 20,000 thermocyling, the mean tensile bond strength of the sandblasted group exhibited a 50% reduction in bond strength, while the others showed a $20\sim30%$ reduction. o Observation of the metal-resin interface revealed that in all groups the resin permeated the rough surface formed by sandblasting thereby producing a mechanical bond between the metal and the resin. It was also found that thermocycling resulted in a gap formation at the metal-resin interface of the specimens, and the sandblasted group exhibited a larger gap width than the other groups. o In fracture mode, all specimens indicated a cohesive fracture within the resin before thermocycling. However, thermocyling produced adhesive failure at the edge of the resin-metal interface in most specimens. The sandblasted group, which exhibited the lowest bond strength after thormocycling, also demonstrated the largest area of adhesive failure.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.13 no.6
• /
• pp.1127-1132
• /
• 2010

Borosilicate glass was prepared in the composition of 81% $SiO_2$, 4% $Na_2O$, 2% $Al_2O_3$, 13% $B_2O_3$. The albite phase($NaAlSi_3O_8$) increased with the $ZrO_2$(0~10wt.%) addition. For measurement of glass transition temperature($T_g$), crystallization temperature($T_{c,max}$) measured by differential thermal analysis. The $T_g$ and $T_{c,max}$ were $510{\sim}530^{\circ}C$ $650{\sim}670^{\circ}C$, respectively. The crystallized glass was heated at various conditions(temperature, time). After nucleation at $550^{\circ}C$ for 2hours prior to crystal growth at $650^{\circ}C$ for 4hours, the resulting Vickers hardness, fracture toughness and bending strength were about $736H_v$, $1.0779MPa{\cdot}m^{1/2}$, and 493MPa, which were 17%, 45% and 149% higher than parent borosilicate glass, respectively. Crystal size and transmittance of crystallized borosilicate glass were analyzed by FE-SEM, EDX and UV-VIS-NIR spectrophotometer. Transmittance of crystallized borosilicate glass was decreased with increasing $ZrO_2$(wt%) at visible-range. The results prove that light-weight bulletproof can be fabricated by the crystallization of borosilicate glass.

• Journal of the Microelectronics and Packaging Society
• /
• v.26 no.4
• /
• pp.113-118
• /
• 2019

In this study, we investigated the growth of single-crystallinity α-Ga₂O₃ thin films on c-plane sapphire substrates using halide vapor pressure epitaxy. We also found the optimal growth conditions to suppress the phase transition of α-Ga₂O₃. Our results confirmed that the growth temperature and partial pressure of the reactive gas greatly influenced the crystallinity. The optimal growth temperature range was about 460~510℃, and the α-Ga₂O₃ thin films with the highest crystallinity were obtained at a III/VI ratio of 4. The thickness and surface morphology of the thin films was observed by scanning electron microscopy. The film thickness was 6.938 ㎛, and the full width at half maximum of the ω-2θ scan rocking curve was as small as 178 arcsec. The optical band gap energy obtained was 5.21 eV, and the films were almost completely transparent in the near-ultraviolet and visible regions. The etch pit density was found to be as low as about 6.0 × 10⁴ cm^-2.

• Journal of Periodontal and Implant Science
• /
• v.35 no.2
• /
• pp.491-510
• /
• 2005

This study was performed to evaluate the effect of inorganic polyphosphate on bone formation in the calvaria of rabbit in the procedure of guided bone regeneration with bovine cancellous bone graft and titanium reinforced expanded polytetrafluoroethylene(TR-ePTFE) membrane. The rabbits were divided into four groups. Control group I used only TR-ePTFE membrane, control group II used TR-ePTFE membrane and deproteinized bovine bone mineral soaked in saline, experimental group III and IV used TR-ePTFE membrane and deproteinized bovine bone mineral soaked in 1% or 2% inorganic polyphosphate respectively. After decortication in the calvaria, GBR procedure was performed on 12 rabbits with titanium reinforced ePTFE membrane filled with deproteinized bovine bone mineral soaked in saline or inorganic polyphosphate. The animals were sacrificed at 2 weeks, 4 weeks, and 8 weeks after the surgery. Decalcified and non-decalcified specimens were processed for histologic and immunohistochemistric analysis. 1. Titanium reinforced ePTFE(TR-ePTFE) membrane showed good spacemaking and cell occlusiveness capability, but it showed poor wound stabilization. 2. The deproteinized bovine bone mineral did not promote bone regeneration, but it acted as a space filler. 3. There was no complete resorption of the deproteinized bovine bone mineral within 8 weeks. 4. 1% inorganic polyphosphate did not promote bone formation, but 2% inorganic polyphosphate promoted bone formation. Within the above results, 2% inorganic polyphosphate could be used effectively for bone regeneration.

• Biotechnology and Bioprocess Engineering:BBE
• /
• v.11 no.6
• /
• pp.510-515
• /
• 2006

The putative EPA synthesis gene cluster was mined from the entire genome sequence of Shewanella oneidensis MR-1. The gene cluster encodes a PKS-like pathway that consists of six open reading frames (ORFs): ORFSO1602 (multi-domain beta-ketoacyl synthase, KS-MAT-4ACPs-KR), ORFSO1600 (acyl transferase, AT), ORFSO1599 (multi-domain beta-ketoacyl synthase, KS-CLF-DH-DH), ORFSO1597 (enoyl reductase, ER), ORFSO1604 (phosphopentetheine transferase, PPT), and ORFSO1603 (transcriptional regulator). In order to prove involvement of the PKS-like machinery in EPA synthesis, a 20.195-kb DNA fragment containing the genes was amplified from S. oneidensis MR-1 by the long-PCR method. Its identity was confirmed by the methods of restriction enzyme site mapping and nested PCR of internal genes orfSO1597 and orfSO1604. The DNA fragment was cloned into Escherichia coli using cosmid vector SuperCos1 to form pCosEPA. Synthesis of EPA was observed in four E. coli clones harboring pCosEPA, of which the maximum yield was 0.689% of the total fatty acids in a clone designated 9704-23. The production yield of EPA in the E. coli clone was affected by cultivation temperature, showing maximum yield at $20^{\circ}C$ and no production at $30^{\circ}C$ or higher. In addition, production yield was inversely proportional to glucose concentration of the cultivation medium. From the above results, it was concluded that the PKS-like modules catalyze the synthesis of EPA. The synthetic process appears to be subject to regulatory mechanisms triggered by various environmental factors. This most likely occurs via the control of gene expression, protein stability, or enzyme activity.

• Journal of Communications and Networks
• /
• v.13 no.5
• /
• pp.499-510
• /
• 2011

Any server offering a routing service in the Internet would naturally be in competition for clients, and clients may need to utilize service from a specific server in order to achieve a desired result. We study the various properties of this competition, such as the fraction of route requests handled by a routing service provider and the fraction of total revenue obtained. As the routing service providers (i.e., servers or routers in this context) compete, they may alter behavior in order to optimize one of the above properties. For example, a service provider may lower the price charged for its service, in order to increase the number of clients served. Our models are based on servers offering a routing service to clients within representative network topologies based on actual Internet sub-graphs. These models provide, a framework for evaluating competition in the Internet. We monitor key aspects of the service, as several variables are introduced into the models. The first variable is the fraction of client requests that will pay more for a better quality route. The remaining requests are normal client requests that are satisfied by the most economical route. The second variable is the fraction of servers who choose to lower service prices in order to maximize the number of client requests served. As this fraction increases, it is more likely that a server will lower the price. Finally, there are some resource constraints applied to the model, to increase the difficulty in providing a routing solution, i.e., to simulate a realistic scenario. We seek to understand the effect on the overall network, as service providers compete. In simple cases, we show that this competition could have a negative impact on the overall efficiency of a service. We show that the routing variety present in the larger models is unable to mask this tendency and the routing service performance is decreased due to competition.

• Textile Coloration and Finishing
• /
• v.8 no.5
• /
• pp.7-16
• /
• 1996

The air-flow dyeing machine is a new type of dyeing machine. Which is an energy saving type to be able to dye the fabrics with the lowest liquor ratio and in shorter time. This machine is operated with an aerodynamic system rather than a hyd raulic system for traditional jet or overflow dyeing. An air-flow dyeing machine(Green-flow) by the use of aerodynamic technology was developed and compared with the Luft-roto machine made by Thies Company, Germany, in this study. Three samples were dyed with both machines under the same dyeing conditions and color fastness, dyeing levelness, drapability, and mechanical properties of these samples were compared. The results were as follows; Both machines have almost the same dyeability. The dyeability was good at liquor ratio of 1: 3.5 and the speed of 450yds/min. The order for drapability was Crepe de Chine > Cool Peach > Charmeuse. Except for the color fastness of sublimation being below class 4, most color fastness of samples dyed with Green-flow m/c were above class 4. The maximum speed was 510yds/min. for Crepe de Chine and the standard deviation of K/S value was lower for Charmeuse and Cool Peach when employed on the "Green-flow" machine and lower for Crepe de Chine when employed on the Luft-roto machine. Comparing with dyeing of the Green-flow machine and that of the Luft-roto machine, the RT of the Charmeuse was found to be higher with the Green-flow machine and thus the sample had an improved wrinkle recovery. LT and WT of Cool Peach were higher, and shear properties(G, 2HG, 2HGS) of Crepe de Chine were higher, both turning out as suitable for clothing. clothing.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2006.05a
• /
• pp.510-513
• /
• 2006

Mobile Ad-hoc networks have recently attracted a lot of attention in the research community as well as in industry. Although the previous research mainly focused on various of Ad-hoc in routing we consider, in this paper, how to efficiently support applications such as variable Geocasting basd on Ad-hoc networks. The goal of a geocasting protocol is deliver data packets to a group of nodes that are located within a specified geocasting region. Previous research that support geocast service in mobilie computing based on Ad-hoc have the non-optimization problem of data delivery path, overhead by frequent reconstruction of the geocast tree, and service disruption problem. In this paper, we propose the mobility pattern based geocast technique using variable service range according to the mobility of destination node and resource reservation to solve this problem. The experimental results show that our proposed mechanism has improved performance than previous research.

• Proceedings of the KSRS Conference
• /
• 2002.10a
• /
• pp.208-208
• /
• 2002

Relationship between chlorophyll a in the East China Sea and spectral bands (412, 443,490, (510), 555, (676,765) in) of OSMI (Ocean Scanning Multi-Spectral Imager) including the profile multi-spectral radiometer (PRR-800) was studied. The values of remote sensing reflectance (Rrs) at the bands corresponding to the field chlorophyll a in α in the East China Sea were much higher than those in clear waters off California, USA. In case of the particle absorptions related to the chlorophyll a concentration at the spectral bands (440, 670 nm) were much higher in the East China Sea than the ones in the clean waters off California. The normalized water leaving radiances (nLw) at 412, 443, 490, 555 m of OSMI and field chlorophyll a in the East China Sea were correlated each other. According to the results, the relationship between field chlorophyll a and nLw 410 m in OSMI bands was the lowest, whereas that between the field chlorophyll a and nLw 555 nm in the bands was the highest. Reciprocal action between the field chlorophyll a and the band ratio of the OSMI bands (nLw410/nLw555, nLw443/nLw555, nLw490/nLw555) was also studied. Correlation between the chlorophyll a and the band ratio (nLw490/nLw555) was highest in the OSMI bands. Relationship between the chlorophyll a and the ratio (nLw443/nLw555) was higher than one in the nLw410/nLw555. The difference in the estimated chlorophyll α (mg/m3) between OSMI and SeaWiFS (Sea Viewing Wide Field-of-View Sensor) at the special observing stations in the northern eastern sea of Jeju Island in february 25, 2002 was about less than 0.3 mg/m3 within 3 hours. It is suggested that OC2 (ocean color chlorophyll 2 algorithm) be used to get much better estimation of chlorophyll α from OSMI than the ones from the updated algorithms as OC4.