• 한국분말재료학회지
• /
• 제25권5호
• /
• pp.390-394
• /
• 2018

Metallic tantalum powder is manufactured by reducing tantalum oxide ($Ta_2O_5$) with magnesium gas at 1,073-1,223 K in a reactor under argon gas. The high thermodynamic stability of magnesium oxide makes the reduction reaction from tantalum oxide into tantalum powder possible. The microstructure after the reduction reaction has the form of a mixture of tantalum and magnesium oxide, and the latter could be entirely eliminated by dissolving in weak hydrochloric acid. The powder size in SEM microstructure for the tantalum powder increases after acid leaching in the range of 50-300 nm, and its internal crystallite sizes are observed to be 11.5 to 24.7 nm with increasing reduction temperatures. Moreover, the optimized reduction temperature is found to be 1,173 K as the minimum oxygen concentration is approximately 1.3 wt.%.

• 한국연소학회지
• /
• 제11권1호
• /
• pp.11-18
• /
• 2006

In this work, $TiO_2$ nanoparticles were synthesized using $N_2-diluted$ and Oxygen-enriched coflow hydrogen diffusion flames. The effect of flame temperature on the characteristics of the formed $TiO_2$ nanoparticles was investigated. The measured maximum centerline temperature of the flame ranged from 2,103 K for oxygen-enriched flame to 1,339 K for $N_2-diluted$ flame. The visible flame length and the height of the main reaction zone were characterized by direct photographs. The characteristics of synthesized $TiO_2$ nanoparticles were analyzed by SEM and TEM images. From these images, it was evident that the formed nanoparticles were divided into two sorts. In the higher temperature region, over the 1,700 K, $TiO_2$ nanoparticles having spherical shapes with diameters about 60 nm were synthesized. In the lower temperature region, below the 1,600 K, the diameters of formed nanoparticles having unclear boundaries were ranged from 35 - 50 nm.

• JSTS:Journal of Semiconductor Technology and Science
• /
• 제9권1호
• /
• pp.37-50
• /
• 2009

Evaluation results about area scaling capabilities of various SRAM margin-assist techniques for random $V_T$ variability issues are described. Various efforts to address these issues by not only the cell topology changes from 6T to 8T and 10T but also incorporating multiple voltage-supply for the cell terminal biasing and timing sequence controls of read and write are comprehensively compared in light of an impact on the required area overhead for each design solution given by ever increasing $V_T$ variation (${\sigma}_{VT}$). Two different scenarios which hinge upon the EOT (Effective Oxide Thickness) scaling trend of being pessimistic and optimistic, are assumed to compare the area scaling trends among various SRAM solutions for 32 nm process node and beyond. As a result, it has been shown that 6T SRAM will be allowed long reign even in 15 nm node if ${\sigma}_{VT}$ can be suppressed to < 70 mV thanks to EOT scaling for LSTP (Low Standby Power) process.

• Bulletin of the Korean Chemical Society
• /
• 제27권12호
• /
• pp.1997-2001
• /
• 2006

The photodissociation dynamics of formic acid (HCOOH) at 206 nm have been investigated from rotationally resolved laser induced fluorescence spectra of OH ($^2\Pi$) fragments produced exclusively in the ground state. From the spectra, the rotational energy of the fragments was measured to be $820\;{\pm}\;50\;cm^{-1}$. The translational energy released in the products, which is 87% of the total available energy of the system, was also measured from analyses of the Doppler profiles. Joining these data with quantum chemical molecular orbital calculations, we have concluded that the dissociation should take place along the S1 surface with an exit channel barrier and also that the energy partitioning is determined at the exit channel.

• Journal of information and communication convergence engineering
• /
• 제13권1호
• /
• pp.50-55
• /
• 2015

We report design and simulation of a two-dimensional (2D) silicon-based nanophotonic crystal as an optical insulator to enhance the light emission efficiency of light-emitting diodes (LEDs). The device was designed in a manner that a triangular array silicon photonic crystal light insulator has a square trench in the middle where LED can be placed. By varying the normalized radius in the range of 0.3-0.5 using plane wave expansion method (PWEM), we found that the normalized radius of 0.45 creates a large band gap for transverse electric (TE) polarization. Subsequently a series of light propagation simulation were carried out using 2D and three-dimensional (3D) finite-difference time-domain (FDTD). The designed silicon-based light insulator device shows optical characteristics of a region in which light propagation was forbidden in the horizontal plane for TE light with most of the visible light spectrum in the wavelength range of 450 nm to 600 nm.

• 한국공작기계학회논문집
• /
• 제18권1호
• /
• pp.22-28
• /
• 2009

In order to optimize the polishing process, Run to Run control scheme has been applied to the micro mold polishing in this study. Also, to fully understand the effect of parameters on the surface roughness a design of experiment is performed. By linear approximation of main factors such as gap and rotational speed of micro quill, EWMA (Exponential Weighted Moving Average) gradual mode controller is adopted as a optimizing tool. Consequently, the process converged quickly at a target value of surface roughness Ra 10nm and Rmax 50nm, and was hardly affected by unwanted process noises like initial surface quality and wear of magnetic abrasives.

• 대한기계학회논문집B
• /
• 제32권8호
• /
• pp.589-596
• /
• 2008

An orifice type of aerodynamic lens is generally used to focus nanoparticles. However, it is impossible to focus particles smaller than 10nm in air due to flow instability of fluid in a lens. In this study, we propose a new converging-diverging type of the aerodynamic lens capable of focusing particles of 5-50nm in air. Designing factors of the lens configurations is also extracted and explained in detail through a numerical simulation. It was demonstrated that the aerosols are delivered from the entrance to the downstream of the lens system with 90% transmission efficiency. The final beam diameters are shown to be more or less 1mm in the range of particle size.

• 한국반도체및디스플레이장비학회:학술대회논문집
• /
• 한국반도체및디스플레이장비학회 2003년도 추계학술대회 발표 논문집
• /
• pp.109-116
• /
• 2003

Amorphous GaN Quantum dots(a-GaN QDs) with particle diameters less than bohr radius(~11nm) were successfully fabricated at room temperature by a laser ablation of high densified GaN target. Transmission electron microscopy, SAED diffraction pattern and X-ray photoelectron spectroscopy confirmed the presence of a-GaN QDs with particle size of 7.9, 6.9, 4.4nm under the Ar gas pressures of 50, 100 and 200 Pa, respectively. The room temperature PL and absorbance spectra showed a strong band emission centered at 3.9 eV in a-GaN QDs made under the gas pressures of 100 and 200 Pa, which is nearly 0.5eV blueshifted with respect to the bulk crystal band gap.

• Bulletin of the Korean Chemical Society
• /
• 제30권11호
• /
• pp.2669-2674
• /
• 2009

Controlled reduction of silver alkylcarbamate complexes with hydrogen gas was investigated as a facile synthetic method for high concentrations of silver nanocolloids in organic solvent. Polyvinylpyrrolidone (PVP) was used to stabilize the silver colloids obtained from the chemical reduction. To determine optimum conditions for preparation of the stable and controlled silver colloids with the narrowest particle size and distribution, a large number of experiments were carried out involving variations in the concentrations of the silver 2-ethylhexylcarbamate (Ag-EHCB) complex, PVP, and 2-propanol. The initial colloid had a mean particle diameter between 5$\sim$50 nm, as measured by transmission electron microscopy, and exhibited a sharp absorption band in the UV region with a maximum size near 420 nm. After treatment with a reducing agent, the colloids were characterized by ultraviolet-visible spectroscopy, X-ray diffraction, and high-resolution transmission electron microscopy.

• 한국광학회지
• /
• 제2권2호
• /
• pp.108-113
• /
• 1991

This paper describes the necessity and utility of Langmuir-Blodgett (L-B) methods in developing molecular electronic devices. It also covers the application area and limitations of the methods. With L-B methods, the membrane thickness can be controlled in a range of 50 nm and 1000 nm depending on nature of the materials and layering methods. The molecular arrangement within the membrane can be altered by altering the surface pressure and nature of the layering materials. Such a variation can be altered by altering the surface pressure and nature of the layering materials. Such a variation can offer a new application of the methods to the future electronic devices. More over 2nd and 3rd nonlinearity generated in the nonsymmetric thin membrane will be used in the development of the optoelectronic devices.