• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.54 no.10
• /
• pp.438-442
• /
• 2005

Si nanocrystal (Si NC) memory device has several advantages such as better retention, lower operating voltage, reduced punch-through and consequently a smaller cell area, suppressed leakage current. However, the physical and electrical reasons for this behavior are not completely understood but could be related to interface states of Si NCs. In order to find out this effect, we characterized electrical properties of Si NCs embedded in a SiO$_{2}$ layer by scanning probe microscopy (SPM). The Si NCs were generated by the laser ablation method with compressed Si powder and followed by a sharpening oxidation. In this step Si NCs are capped with a thin oxide layer with the thickness of 1$\~$2 nm for isolation and the size control. The size of 51 NCs is in the range of 10$\~$50 m and the density around 10$^{11}$/cm$^{2}$ It also affects the interface states of Si NCs, resulting in the change of electrical properties. Using a conducting tip, the charge was injected directly into each Si NC, and the image contrast change and dC/dV curve shift due to the trapped charges were monitored. The results were compared with C-V characteristics of the conventional MOS capacitor structure.

• Proceedings of the SAREK Conference
• /
• 2008.06a
• /
• pp.1025-1030
• /
• 2008

We develop heat exchanger modules for a multi-burner boiler. The heat exchanger module is kind of a heat recovery steam generator (HRSG). This heat recovery system has 4 heat exchanger modules. The 1st module consists of 27 bare tubes due to high temperature exhaust gas and the others consist of 27 finned tubes. The maximum steam pressure of each module is 10 bar and tested steam pressure is 4 bar. In order to test these heat exchanger modules, we make a 0.5t/h flue tube boiler (LNG, $40\;Nm^3/h$). The test results of 100% boiler load show that heat transfer rate of 1st module is 49.7 Mcal/h which is 34% of total heat transfer rate and that of 2nd module is 82.6 Mcal/h which is 57% of total heat transfer rate. The reason of higher the heat transfer rate of 2nd module than that of 1st module is that the 2nd heat exchanger module has finned tubes instead of bare tube. The boiler load 50% results show that only 2 heat exchanger modules are needed to extract the heat from the flue gas to water. From this result, it is very important of optimum design of the first finned tube among all water tubes.

• Korean Journal of Medicinal Crop Science
• /
• v.16 no.6
• /
• pp.402-408
• /
• 2008

This study was performed to investigate improving immune activities of natural water-soluble sulforaphane extracted from Brassica oleracea var. italica by nano encapsulation process. The nanoparticles of the sulforaphane extracted with ultrasonification process at $60^{\circ}C$ promoted human B and T cell growth, about $7{\sim}35%$ compared to the control. The secretion of IL-6 and TNF-${\alpha}$ from T cells were also enhanced as $2.6{\times}10^{-4}pg/cell$ and $2.1{\times}10^{-4} pg/cell$, respectively, by the adding nano samples. NK cell activation was improved about 8%, compare to the control in adding cultured medium of T cell added nano samples. It was also found that sulforaphane extracted from B. oleracea var. italica had highly inhibitory activity on hyaluronidase as $IC_{50}$ about $200\;{\mu}g/m{\ell}$. It can be concluded that natural water-soluble sulforaphane samples by nano-encapsulation, each size is 200 nm, extracted from B. oleracea var. italica has high immune activities through higher efficiency of bio-activation than conventional extracts.

• Korean Journal of Materials Research
• /
• v.19 no.5
• /
• pp.240-244
• /
• 2009

Simple and high efficiency green phosphorescent devices using an intermixed double host of 4, 4', 4"-tris(N-carbazolyl) triphenylamine [TCTA], 1, 3, 5-tris (N-phenylbenzimiazole-2-yl) benzene [TPBI], phosphorescent dye of tris(2-phenylpyridine)iridium(III) [$Ir(ppy)_3$], and selective doping in the TPBI region were fabricated, and their electro luminescent characteristics were evaluated. In the device fabrication, layers of $70{\AA}$-TCTA/$90{\AA}$-$TCTA_[0.5}TPBI_{0.5}$/$90{\AA}$-TPBI doped with $Ir(ppy)_3$ of 8% and an undoped layer of $50{\AA}$-TPBI were successively deposited to form an emission region, and SFC137 [proprietary electron transporting material] with three different thicknesses of $300{\AA}$, $500{\AA}$, and $700{\AA}$ were used as an electron transport layer. The device with $500{\AA}$-SFC137 showed the luminance of $48,300\;cd/m^2$ at an applied voltage of 10 V, and a maximum current efficiency of 57 cd/A under a luminance of $230\;cd/m^2$. The peak wavelength in the electroluminescent spectral and color coordinates on the Commission Internationale de I'Eclairage [CIE] chart were 512 nm and (0.31, 0.62), respectively.

• Proceedings of the Korea Crystallographic Association Conference
• /
• 2003.05a
• /
• pp.11-11
• /
• 2003

전자현미경내에서 일부 무기 및 금속 시료들은 전자빔 조사에 의해 시료구조가 손상되거나 비정질화 또는 상전이 등과 같은 구조전이 현상들을 겪게 된다. 즉, 전자빔 조사에 의해 시료는 원자간 결합이 끊어져 나타나는 Knock-on damage, 시료 원자 주위의 전자들과의 상호 작용에 의해 나타나는 Ionization damage, 빔 에너지의 시료온도 상승 기여에 의한 Radiolysis damage 등의 현상들을 경험하게 된다. 이러한 현상은 전자현미경의 가속전압, 전자밀도, 시료 조건 등에 따라 그 지배기구가 다르며 동일한 시편이라도 시료의 두께와 시편온도를 결정하는 전자빔 조사선량에 따라 그 양상과 전이 속도가 달라진다. 본 연구에서는 전자빔 조사에 의해 구조 전이를 겪게 되는 대표적 무기수화물의 하나인 Cibbsite에 대해 전자빔 조사효과에 대한 정량적 고찰을 에너지 여과 투과전자현미경 (EF-TEM)을 이용하여 시도하였다. 전자빔 조사는 120분까지 실시하였고 각 시간별로 에너지 필터와 Imaging plate를 이용하여 Gibbsite의 회절패턴과 미세조직 변화를 기록하였다 빔조사 시엔 illumination angle을 1.25mrad(Dose rate : 334 × 10³ e/sup -//sec·n㎡)으로 하였으며 사진기록 시엔 최소 illumination angle인 0.04mrad(Dose rate : 413 e/sup -//sec·n㎡)을 사용하였다. 시료의 관찰방향은 [001]방향이고 관찰시료두께는 약 50nm로 평가되었으며 시료의 화학변화는 EDS를 이용하여 분석하였다. 회절자료의 Intensity는 ELD/CRISP 프로그램을 이용하였으며 빔조사선량은 평행조사빔이 시료와 상호 작용하는 면적과 상호작용하지 않을 때의 빔을 회절모드에서 faraday cup으로 측정한 빔전류로 부터 계산하였다. Gibbsite에 대한 전자빔 조사 시 1분 이내에 급격한 Hydroxyl Ion(OH-)의 이탈로 인해 Cibbsite의 구조는 거시적 비정질화가 되며 시간증가에 따라 χ-alumina → ν-alumina → σ-alumina or δ-alumina의 순으로 상전이를 겪는다. 전자빔 조사 시 관찰된 회절자료의 가시적 변화를 통해 illumination angle 1.25mrad(Dose rate : 334 × 10³ e/sup -//sec·n㎡)일 경우 약 3초 이내에 비정질화가 시작됨을 알 수 있었고 이는 약 1 × 10/sup 6/ e/sup -//sec·n㎡ 의 전자선량에 해당되며 이를 기준으로 각각의 illumination angle에 대한 임계전자선량을 평가할 수 있었다. 실질적으로 Cibbsite와 같은 무기수화물의 직접가열실험 시 전자빔 조사에 의해 야기되는 상전이 영향을 배제하고 실험을 수행하려면 illumination angle 0.2mrad (Dose rate : 8000 e/sup -//sec·n㎡)이하로 관찰하고 기록되어야 함을 본 자료로부터 알 수 있었다.

• Korean Journal of Materials Research
• /
• v.18 no.5
• /
• pp.283-288
• /
• 2008

The effect of sintering aids and glass-frit on the densification and resistivity of silver paste was investigated in an effort to enhance the sintered density and electrical conductivity of the silver electrode. To prepare Pb-free silver paste for use at low sintering temperatures, two commercial silver powders ($0.8\;{\mu}m$ and $1.6\;{\mu}m$ in size) and 5wt.% lab-synthesized nanoparticles (30-50 nm in size) as a sintering aids were mixed with 3 wt.% or 6 wt.% of glass frit ($Bi_2O_3$-based) using a solvent and three roll mills. Thick films from the silver paste were prepared by means of screen printing on an alumina substrate followed by sintering at $450^{\circ}C$ to $550^{\circ}C$ for 15 min. Silver thick films from the paste with bimodal particles showed a high packing density, high densification during sintering and low resistivity compared to films created using monomodal particles. Silver nanoparticles as a sintering aid enhanced the densification of commercial silver powder at a low sintering temperature and induced low resistivity in the silver thick film. The glass frit also enhanced the densification of the films through liquid phase sintering; however, the optimum content of glass frit is necessary to ensure that a dense microstructure and low resistivity are obtained, as excessive glass-frit can provoke low conductivity due to the interconnection of the glass phase with the high resistivity between the silver particles.

• 한국태양에너지학회:학술대회논문집
• /
• 2011.11a
• /
• pp.245-248
• /
• 2011

Many researches have been carried out to improve light absorption in the crystalline silicon solar cell fabrication. The rear reflection is applied to increase the path length of light, resulting in the light absorption enhancement and thus the efficiency improvement mainly due to increase in short circuit current. In this paper, we manufactured the silicon solar cell using the mono crystalline silicon wafers with $156{\times}156mm^2$, 0.5~3.0 ${\Omega}{\cdot}cm$ of resistivity and p-type. After saw damage removal, the dielectric film ($SiN_x$)on the back surface was deposited, followed by surface texturing in the KOH solution. It resulted in single-side texturing wafer. Then the dielectric film was removed in the HF solution. The silicon wafers were doped with phosphorus by $POCl_3$ with the sheet resistance 50 ${\Omega}/{\Box}$ and then the silicon nitride was deposited on the front surface by the PECVD with 80nm thickness. The electrodes were formed by screen-printing with Ag and Al paste for front and back surface, respectively. The reflectance and transmittance for the single-sided and double-sided textured wafers were compared. The double-sided textured wafer showed higher reflectance and lower transmittance at the long wavelength region, compared to single-sided. The completed crystalline silicon solar cells with different back surface texture showed the conversion efficiency of 17.4% for the single sided and 17.3% for the double sided. The efficiency improvement with single-sided textured solar cell resulted from reflectance increase on back surface and light absorption enhancement.

• Journal of the Society of Naval Architects of Korea
• /
• v.57 no.4
• /
• pp.241-253
• /
• 2020

The Small-Unit Riverine Craft (SURC) is a small high-speed vessel used by navies and marine corps in relatively shallow waterway environments, such as riverine areas or littoral coasts. In the past, SURCs have primarily been rigid-hulled inflatable boats constructed using composite materials such as glass fiber reinforced plastics. More recently, single-hull SURCs have been manufactured using aluminum for weight reduction. In this study, a Carbon Fiber Reinforced Polymer (CFRP) material was applied instead to examine its feasibility in the basic design of an SURC with a hull length of 10 m. The CFRP structural design was obtained using the properties of a marine CFRP laminate, determined in a previous study. Next, the designed CFRP SURC was modeled to confirm its functionality, then compared with existing aluminum SURCs, indicating that the CFRP SURC was 41.49 % lighter, reduced fuel consumption by 30 %, and could sail 50 NM further for every hour of engine operation. A method for reducing the high cost of carbon fiber was also proposed based on the adjustment of the carbon fiber content to provide the optimum strength where required. The data developed in this study can be used as a basis for further design of CFRP craft.

• Journal of Welding and Joining
• /
• v.26 no.4
• /
• pp.50-54
• /
• 2008

In this research, anode for SOFC has been manufactured from two different kinds of feedstock materials through thermal spraying process and the properties of the coatings were characterized and compared. One kind of feedstock was manufactured from spray drying method which includes nano-components of NiO, YSZ (300 nm) and graphite. And the other is manufactured by blending the micron size NiO coated graphite, YSZ and graphite powders as feedstock materials. Microstructure, mechanical properties and electrical conductivity of the coatings as-sprayed, after oxidation and after hydrogen reduction containing nano composite which is prepared from spray-dried powders were evaluated and compared with the same properties of the coatings prepared from blended powder feedstock. The coatings prepared from the spray dried powders has better properties as they provide larger triple phase boundaries for hydrogen oxidation reaction and is expected to have lower polarization loss for SOFC anode applications than that of the coatings prepared from blended feedstock. A maximum electrical conductivity of 651 S/cm at $800^{\circ}C$ was achieved for the coatings from spray dried powders which much more than that of the average value.

• Korean Journal of Veterinary Research
• /
• v.40 no.2
• /
• pp.325-332
• /
• 2000

The growth characteristics and the cellular protein patterns of the Lactobacillus plantarum isolated and identified from oat silage were examined in order to confirm whether it will be used practically as probiotics or not. L plantarum was identified by morphological and biochemical tests including of final conforming by API 50CHL kit. The cultivation in MRS broth of the strain under the condition of different temperature, proved that they grew into $2.0{\times}10^{9}$ in $25^{\circ}C$, into $1.4{\times}10^{9}$ in $35^{\circ}C$ but they decreased into $4.5{\times}10^{5}$ growth in $45^{\circ}C$. The comparison of the growth by measurement of O.D600nm value after 24 hour cultivation between L plantarum and commercial probiotics, showed that the strain had a higher growth than commercial as 1.841 : 1.623. The measurement of it under bile acid's existence, indicated that this isolation was not influenced by bile acid and the tolerance was $3.2{\times}10^{9}$, $3.9{\times}10^{9}$ and $3.2{\times}10^{9}$, respectively, when each of 0%, 1%, and 2% oxigall existed. The examination of their antibiotics susceptibility by disk diffusion test, proved that L plantarum showed resistance against danofloxacin(5mcg), gentamycin(10mcg), kanamycin(30mcg), neomycin(30mcg) and streptomycin(10mcg). Based upon the test of the bacteriocin formation of this L plantarum, it was found out that the inhibition zone was not formed. In growth of L plantarum and E coli in nutrient broth, all E coli died out within 6 hours after cultures.