• Publications of The Korean Astronomical Society
• /
• v.30 no.2
• /
• pp.433-437
• /
• 2015

We show the results of a time series analysis of the long-term light curves of four blazars. 3C 279, 3C 345, 3C 446, and BL Lacertae. We used densely sampled light curves spanning 32 years at three frequency bands (4.8, 8, 14.5 GHz), provided by the University of Michigan Radio Astronomy Observatory monitoring program. The spectral indices of our sources are mostly flat or inverted (-0.5 < ${\alpha}$ < 0), which is consistent with optically thick emission. Strong variability was seen in all light curves on various time scales. From the analyses of time lags between the light curves from different frequency bands and the evolution of the spectral indices with time, we find that we can distinguish high-peaking flares and low-peaking flares according to the Valtaoja et al. classification. The periodograms (temporal power spectra) of the light curves are in good agreement with random-walk power-law noise without any indication of (quasi-)periodic variability. We note that random-walk noise light curves can originate from multiple shocks in jets. The fact that all our sources are in agreement with being random-walk noise emitters at radio wavelengths suggests that such behavior is a general property of blazars. We are going to generalize our approach by applying our methodology to a much larger blazar sample in the near future.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.16 no.5
• /
• pp.899-905
• /
• 2012

Level Gauge using FMCW Radar is widely used and researched in many areas because of contactless, long range and flexibility. However FMCW level gauge requires wideband RF bandwidth for archiving high resolution of cm grade. In this paper we propose a new tx sawtooth waveform and processing algorithm with narrowband RF for wideband performance. The proposed method is based on STFT(Short-time fourier transform) and single sinusoidal carrier estimation method. From some experiments, we show that the resolution is improved upto 8 times with 300MHz FMCW radar.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.22 no.1
• /
• pp.252-264
• /
• 2023

This paper proposes a design of a dual-band band-pass filter that integrates a λg/2 open SIR structure, a transmission line, and a fork-type structure with symmetric and asymmetric open stubs. To obtain the dual-band effect, the proposed filter uses the SIR structure and adjusts the impedance ratio of the SIR structure. Therefore, the position of the harmonics of the filter is shifted through the adjustment of the impedance ratio, and this can obtain a double-band effect. In order to obtain the dual-band characteristics, the dual-band effect is obtained by inserting a open stub between the SIR structures with the SIR structure divided in half. In addition, the second frequency response is obtained by adjusting the length of the open symmetrical stub in the fork-shaped structure. The asymmetrical open stub in the fork form achieves optimum bandwidth by adjusting the length. Therefore, the first center frequency of the proposed band-pass filter is 5.896 GHz and the bandwidth is 13.6 %. At this time, the measurement results are 0.13 dB and 33.6 dB. The second center frequency is 5.906 GHz and the bandwidth is 13.6 %. At this time, the measurement results are 0.15 dB and 19.8 dB. The reason is that when the impedance ratio (Δ) is higher than 1, the position of the harmonic is shifted to a lower frequency band. However, if the impedance ratio (Δ) is lowered by one step, the position of harmonics will move to a higher frequency band. The function of the filter designed using these characteristics can be obtained from the measurement result. The proposed band-pass filter has no coupling loss and no via energy concentration loss because there is no coupling structure of input/output and no via hole. Therefore, system integration is possible due to its excellent performance, and it is expected that dedicated short-range communication (DSRC) system applications used in traffic communication systems will be possible.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.13 no.6
• /
• pp.485-492
• /
• 2000

The sintering characteristics and the effects of density on dielectric properties in 0.2Ba(Mg$_{1}$3(Nb$_{2}$3/)O$_3$-0.8Ba(Mg$_{1}$3//Ta$_{2}$3/)O$_3$ceramics were investigated. The samples were made by the powder mixing techniques with the two step calcining conditions. When the 1st and the 2nd calcining temperatures were 120$0^{\circ}C$ and the sintering temperature was 155$0^{\circ}C$the density of samples showed the highest value (7.45 g/cm$^3$, 98.5% of theoretical density) among them. The dielectric constant of samples was nearly independent of density but the tan $\delta$ and the temperature coefficient of dielectric constant decreased linearly with increasing of the density. The quality factor(Q$\times$f), the temperature coefficient of resonance frequency and the dielectric constant of Ba[Mg$_{1}$3(Nb$_{0.2}$/Ta$_{0.8}$)sub 2/3/]O$_3$ceramic were 79,548 GHz, +1.5 ppm/$^{\circ}C$ and 26 in the microwave range, respectively.ely.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.65 no.6
• /
• pp.1083-1088
• /
• 2016

25.8kV GIS part generated by sensors to measure contact an inflow of noise depending on the extent of the measured discharge occurs often not easy. Partial discharge signal measurement sensor suitable for developing a more useful measurements at the scene to this, partial discharge waveform analysis developed a sensor, and to utilize forSensor on the development of the most important is VSWR decided to (voltage standing wave ratio) voltage standing-wave ratio less than 1.5 and decided less than at the full spectrum bands that are measured, this time Return loss, as measured value by absolute criteria 14.0 dB produced the sensor, designed to or more. UHF 1.5~0.5 GHz bandwidth spectrum to be measured in GIS. UHF bands were designed to be able to measure the best signal. Recently, 25.8kV GIS production company has been increasing variety of GIS were made open spacer in partial discharge in accordance with the not very easy to detect the signal. The sensor is designed height of four cm external spacer is attachment GIS in an influx of outside noise measurement, and be so manufactured as to facilitate the least we've done. Also, since partial discharge which occur can measure the frequency of the 170kV GIS external partial-discharge signals that occur at the scene of insulation applied to the spacer. Features, and also derived good results using global positioning. Also measured discharge point about sensors that are stable and the reliability of the development and local substation equipment failure occurring signal analysis through the discharge for the prevention of widely. There should be to believe that used.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.25 no.5
• /
• pp.559-575
• /
• 2014

In this paper, we propose a horizontal/vertical calibration kit for calibrating a vector network analyzer(VNA) to measure the vertical connector pin. If the conventional calibration kit is used, we should change the arm for a probe or need an assistant device and it takes a long time. In addition there is a risk of precision degradation caused by the position change of the probe tip sensitive to the surroundings. We suggest a 4-port vertical calibration kit to make up for the aforementioned shortcomings. The calibration kit was manufactured for the SOLT calibration method. 'Short', 'Open', and 'Load' are available in the horizontal plane, 'Thru' is available not only in the horizontal plane on the two planes of a PCB, but in the vertical plane between the two planes according to the positions of the probes. We complemented the conventional calibration kit to make a vertical calibration kit to be used for the vertical measurement method. We compared and analysed their reflection/transfer characteristics of the SOLT calibration standards of the proposed calibration kit and conventional one, we get a ${\pm}0.1$ dB differences of transfer characteristics in the range from 300 kHz to 8.5 GHz. In order to demonstrate usefulness, and we performed a case study for horizontal and vertical cases, and compared the results of the proposed calibration kit and conventional one.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.22 no.10
• /
• pp.934-940
• /
• 2011

A novel reconfigurable beam steering antenna using double loops is proposed. The double loop antenna has a superposed beam which is produced by combining the in-phase beam in the inner loop with the out-of-phase beam in the outer loop. Also, the doble loop antenna uses two artificial switches to connect between inner loop and outer loop, and has the beam directions of three separate cases(Case 1, Case 2, Case 3) by changing ON/OFF states of switches. The operation frequency of the antenna is 14.5 GHz, and three maximum beam directions of the antenna are ${\phi}_{max}=0^{\circ}$, ${\theta}_{max}=0^{\circ}$(Case 1), ${\phi}_{max}=230^{\circ}$, ${\theta}_{max}=40^{\circ}$(Case 2) and ${\phi}_{max}=130^{\circ}$, ${\theta}_{max}=40^{\circ}$ (Case 3). The peak gains of each case are 6.5 dBi(Case 1), 7.6 dBi(Case 2) and 7.8 dBi(Case 3). The half power beam width(HPBW) of each case is $86{\sim}104^{\circ}$, and the overall HPBW is $160^{\circ}$.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.12 no.5
• /
• pp.2241-2248
• /
• 2011

This paper describes the design of a palette-type 60watt high power amplifier module using gallium nitride(GaN) devices with high power and efficiency performances for WiMAX and LTE systems. The line-up for the high gain amplifier module consists of the pre-amplifier stage with low power and high gain, 8watt GaN driving amplifier stage, and 60watt GaN high power amplifier stage of Doherty structure with two 30watt GaN devices. The obtained gain is 61.4dB with an excellent gain flatness of ${\pm}$0.075dB over 2.5~2.68GHz. GaN devices and the Doherty structure are adopted for the improvement of high efficiency and output power. The measurement for the fabricated high power amplifier module of palette type is performed using the widely known WiMAX signal all over the world. In the example of RRH(remote radio head) application of the fabricated amplifier module, the measured efficiency is 37~38% with the 10watts of modulated output power. It is shown that when the fabricated amplifier module is activated with a digital predistorter(DPD), the measured ACLR is better than 46dBc under the 10watts of modulated output power.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.32 no.5A
• /
• pp.490-496
• /
• 2007

This paper describes the design and implementation of an integrated LTCC front-end module for the IEEE802.11a WLAN applications by performing the behavioral-level simulation using measurement-based behavioral model. To meet the IEEE802.11a WLAN standard, a system transmitting 1024 symbols through 64-QAM process at the rate of 54Mbps should be implemented and nonlinear properties are confirmed by simulations of ACPR and EVM in this circumstance. The right offsets of ACPR which are 30MHz, 20MHz, and 11MHz distant from the center frequency of 5.8GHz are 49.36dBc, 36.90dBc, and 24.58dBc, respectively. The left offsets are 50.14dBc, 30.04dBc, and 28.85dBc, respectively and EVM is 2.94%. The size of the module implemented with LTCC five-layer substrates is $13.4mm{\times}14.2mm$. The measured characteristics of the transmitter show P1dB of 16.2dBm and power gain of 16.73dB. Those of the receiver exhibit the small signal gain of 16.24dB and noise figure of 7.83dB.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.44 no.7 s.361
• /
• pp.41-46
• /
• 2007

A novel post-linearization technique is proposed for CMOS cascode low noise amplifier (LNA). The technique uses dual common gate FETs one of which delivers the linear currents to a load and the other one sinks the $3^{rd}$ order intermodulation currents of output currents from the common source FET. Selective current branching can be implemented in $0.18{\mu}m$ CMOS process by using a thick oxide FET as an IM3 sinker with a normal FET as a linear current buffer. A differential LNA adopting this technique is designed at 2.14GHz. The measurement results show 11dBm IIP3, 15.5dB power gain and 2.85dB noise figure consuming 12.4mA from 1.8V power supply. Compared with the LNA with turning off the IM3 sinker, the proposed technique improves the IIP3 by 7.5 dB.