• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.29 no.3A
• /
• pp.303-310
• /
• 2004

In this paper, L-shaped slot antenna for 5.15㎓-5.35㎓ is designed, fabricated. and measured. The prototype consist of four L-shaped slot. To obtain suitable bandwidth, the form layer is inserted between ground plane and substrate. Important parameters in the design are four L-slot length. width, position, air-gap height. and feed Point position. From these parameters optimized, a four L-shaped slot antenna is fabricated and measured. The measured results of the antenna are obtained as follows results. The resonant frequency of the fabrication four L-shaped slot antenna is 5.25㎓, bandwidth for approximately 5％(VSWR＜1.5) and the gain is 8-9㏈i. The experimental far-field patterns are stable across the pass band. The 3dB bandwidth in H-Plane and I-Plane are 69$^{\circ}$and 62$^{\circ}$, respectively.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.25 no.5B
• /
• pp.985-991
• /
• 2000

In this paper, the optimum structure of 2GHz magnetic thin film planar inductor were designed and fabricated to reduce the inductor area and to maximize the inductance L and quality factor Q of the inductor. The optimum design was performed utilizing Co90Fe10 layer multilayered with SiO2 layers to avoid the eddy-current skin effect and considering new lumped element model. New magnetic thin film inductors operating at 2GHz were fabricated on a Si substrate utilizing photo-lithography and lift-off techniques. The frequency characteristics of L, Q, and impedance in more than fifty identical inductors were measured using an RF Impedance Analyzer(HP4291B with HP16193A test fixture). The self-resonant frequencies(SRF) of the inductors were measured by a Vector Network Analyzer(HP8510). The developed inductors have SRF of 1.8 to 2.3GHz, L of 47 to 68nH, and Q of 70 to 80 near 1GHz. Finally, high frequency, high performance, planar micro-inductor(area=30.8 x 30.8il$^2$) with maximized L and Q were fabricated succefully.

• Composites Research
• /
• v.27 no.6
• /
• pp.225-230
• /
• 2014

In this study, a novel microwave absorber which consists of a structural part, a resistive sheet, and a low dielectric layer is proposed. Unlike the conventional Salisbury screen, a newly proposed absorber is capable of a range of absorbing performance, from narrowband to broadband. In the case of the narrowband absorber, the fabricated absorber with optimized design parameters has a strong resonance at 9.25 GHz and reflection loss of -44 dB with satisfying the -10 dB absorption in whole X-band (8.2 GHz~12.4 GHz). For the broadband absorber design, the reflectivity was minimized in the considered frequency ranges. The designed absorber showed two weak resonances near 6.5 GHz and 16.5 GHz and satisfied the -10 dB absorption from C-band to Ku-band (4 GHz~18 GHz). The measured reflection loss of fabricated absorber was well matched with simulation results, though the measurement was only performed on X-band. For the Salisbury screen to be capable of broadband absorption, it should be stacked multiply in a structure known as the Jaumann absorber. However, for the microwave absorber presented here, broadband as well as narrowband capabilities can be implemented without a change of the structure.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.19 no.1
• /
• pp.19-25
• /
• 2015

In this paper, a design method for a CPW-fed slot antenna for harmonic suppression is studied. The structure of the proposed slot antenna is a rectangular slot antenna appended with stepped impedance resonators (SIRs) at both ends of the slot symmetrically. Optimal design parameters are obtained by analyzing the effects of the length and width of the SIRs on the input reflection coefficient. The optimized harmonic-suppressed slot antenna operating at 2.45 GHz WLAN band is fabricated on an FR4 substrate with a dimension of 42 mm by 30 mm. The slot length of the proposed harmonic-suppressed slot antenna is reduced to 33.3% compared to that of a conventional rectangular slot antenna owing to the appended SIRs. Experiment results show that the antenna has a desired impedance characteristic with a frequency band of 2.39-2.49 GHz for a VSWR < 2, and a measured gain of 2.5 dBi at 2.45 GHz.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.25 no.5
• /
• pp.526-531
• /
• 2014

Vehicular communications have been receiving much attention in intelligent transport systems(ITS) by combining communication technology with automobile industries. In general, vehicular communication can be used for vehicle-to-vehicle(V2V) and vehicle-to-infrastructure( V2I) communication by adopting IEEE802.11p/1609 standard which is commonly known as wireless access in vehicular environment(WAVE). WAVE system transmits signal in 5.835~5.925 GHz frequency band with orthogonal frequency division multiplexing(OFDM) signaling. In this paper, after 32 bit processed the channel monitoring in MAC(Media Access Control) layer of WAVE system implemented according to IEEE 802.11p standard, data were received and we evaluated the performance, we built the test bed consisting of OBU(On Board Unit) in the real expressway. We transmitted WSM(WAVE Short Message) and received WSM between OBU wirelessly. And then, we calculated channel occupancy time per one frame and throughput, and evaluated the performance.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.2 no.2
• /
• pp.125-131
• /
• 2002

This paper presents MMIC drive and power amplifiers covering 6-18 ㎓. For simple wideband impedance matching and less sensitivity to fabrication variation, modified distributed topologies are employed in the both amplifiers. Cascade amplifiers with a self-biasing circuit through feedback resistors are used as unit gain blocks in the drive amplifier, resulting in high gain, high stability, and compact chip size. Self impedance matching and high-pass, low-pass impedance matching networks are used in the power amplifier. In measured results, the drive amplifier showed good return losses ($S_11,{\;}S_{22}{\;}<{\;}-10.5{\;}dB$), gain flatness ($S_{21}={\;}16{\;}{\pm}0.6{\;}dB$), and $P_{1dB}{\;}>{\;}22{\;}dBm$ over 6-18 GHz. The power amplifier showed $P_{1dB}{\;}>{\;}28.8{\;}dBm$ and $P_{sat}{\;}{\approx}{\;}30.0{\;}dBm$ with good small signal characteristics ($S_{11}<-10{\;}dB,{\;}S_{22}{\;}<{\;}-6{\;}dB,{\;}and{\;}S_{21}={\;}18.5{\;}{\pm}{\;}1.25{\;}dB$) over 6-18 GHz.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.25 no.9
• /
• pp.886-894
• /
• 2014

A wideband bow-tie antenna fed by wideband microstrip-coplanar stripline(CPS) balun and band notch structures that can be applied to bow-tie antenna are proposed in this paper. In order to increase bandwidth, bow-tie radiators are reshaped so that the surface current flows continuously, and wideband impedance matching is achieved by adjusting strip width and spacing of CPS feeding line. The VSWR is measured as 2:1 over the wide frequency range of 2.3~12 GHz. The fabricated antenna size is $60mm{\times}60mm$. In order to achieve the band-notch function at WLAN(5.8 GHz), ${\lambda}/4$ folded-slits located ${\lambda}/4$ away from feeding point are utilized. To minimize the slit size, folded-slit type is adopted. The measured VSWR is 7:1 and gain attenuation is 14 dB at 5.8 GHz.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.18 no.8
• /
• pp.930-936
• /
• 2007

In this paper, the high gain and broadband antenna operating for SDMB(Satellite Digital Multimedia Broadcasting) system is realized, The proposed antenna consists of the SAP(Shorted Annular Patch) structure, which inhibits surface-wave and the parasitic SAP element with spacing of $0.25 {\lambda}_0$ in order to improve gain, bandwidth and directivity. The RHCP(Right Hand Circular Polarization) is generated by two slits, which are made along the periphery of the circular patch at the diametrically opposite points, The simulated maximum gain of the proposed antenna is 12.6 dBi, which is better 5.22 dBi than maximum gain of the conventional microstrip patch antenna. The measured maximum gain is 10.5dBi at operating frequency 2.63GHz. Also, the measured impedance bandwidth$(VSWR{\leq}2)$ of the proposed antenna is $360MHz(2.488{\sim}2.848 GHz)$, which is better 300 MHz than the bandwidth of the conventional microstrip patch antenna. The measured HPBW(Half Power Beam Width) of the proposed antenna is $45.8^{\circ}$, and the measured FBR(Front to Back Ratio) is 15.49 dBi, The 3dB axial ratio bandwidth is 220 MHz$(2.54{\sim}2.76 GHz)$.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.25 no.4A
• /
• pp.586-591
• /
• 2000

In this paper, a PLHRO(Phase Locked Hair-pin Resonator Oscillator) for K-band is designed with the feedback property of PLL(Phase Locked Loop) using a new tuning mechanism. The proposed PLHRO generates the output power of -0.6 dBm at 24.42 GHz, and has the phase noise of -86.6 dBc/Hz at 100 KHz and -76.5 dBc/Hz at 10KHz offset from carrier frequency, and has suppression characteristics of -23 dBc and spurious noise of -65 dBc. Buffered 24.42 GHz PLHRO generates the output power of 5.6 dBm at 24.42 GHz and has the of a phase noise of -77.34 dBc/Hz at 100 KHz and -72 dBc/Hz at 100 KHz offset from carrier frequency.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.30 no.10A
• /
• pp.965-970
• /
• 2005

In this paper, SPDT Tx/Rx MMIC switch applicable to IEEE 802.11a WLAN systems is designed and fabricated using a specific designed epitaxial layered pHEMT wafer and ETRI's $0.5{\mu}m$ pHEMT switch process. The SPDT switch exhibits a low insertion loss of 0.68dB, high isolation of 35.64dB, return loss of 13.4dB, power transfer capability of 25dBm, and 3rd order intercept point of 42dBm at frequency of 5.8GHz and control voltage of 0/-3V. The comparison of the measured performances with commercial products based on the GaAs pHEMT technology for low voltage operating at ${\pm}$ 3V/0V shows that the return loss is somewhat inferior to the commercial products and insertion loss is compatible with each other however, isolation characteristics are much better than in conventional chips. Based on these performances, we can conclude that the developed SPDT switch MMIC has an enough potential for IEEE802.11a standard 5 GHz-band wireless LAN applications.