• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.40 no.11
• /
• pp.93-98
• /
• 2003

In this paper, we designed a printed square loop antenna for operating of PCS and IMT2000 band. The proposed antenna has omni-directional radiation patterns with broad bandwidth, similar to the conventional antenna, to easy feed on composing single planar. We obtain an ideal impedance matching and increase bandwidth. An antenna bandwidth is about 150MHz(1.74∼l.89〔GHz〕) at 1$^{st}$ resonance frequency and 290MHz(1.95∼2.24GHz) at 2$^{nd}$ resonance frequency on VSWR(equation omitted)1.5, and then we can obtain not only 1.73∼l.87 〔GHz〕 PCS band but also 1.92∼2.17 (GHz) IMT2000 band. band.

• Proceedings of the IEEK Conference
• /
• summer
• /
• pp.181-184
• /
• 2004

In this paper, we propose the dual band(2.4GHz and 5GHz) antenna for access point of WLAN(Wireless Local Area Network) which has similar radiation patterns for each band. Simulation results by using HFSS(High Frequency Structure Simulator) for the proposed antenna are presented. The electrical characteristics of the proposed antenna are measured with HP 8510C network analyzer and included. And radiation patterns are measured with rectangular anechoic far field antenna chamber. Measured results show that $S_{11}$ is less than - 14dB and VSWR(Voltage Standing Wave Ratio) is less than 1.5 for all frequency bands of interest. The measured maximum gain for elevation pattern at 2.40GHz is about 2.46dBi at $theta=-78^{\circ}$ and maximum gain for 5.825GHz is about 2.70dBi at $theta=-80^{\circ}.$ And the implemented antenna has good radiation pattern characteristic, therefore, we expect that the implemented dual band antenna is applicable for access point of WLAN.

• Journal of Advanced Navigation Technology
• /
• v.25 no.6
• /
• pp.536-542
• /
• 2021

In this paper, we proposed a triple band printed monopole antenna with a bent branch strips for WiFi / 5G. An antenna structure in which bent strips for generating multiple resonance are attached in the form of branches was newly proposed based on a typical monopole strip vertically erected as a triple band antenna structure. The proposed antenna is designed on a FR-4 substrate with dielectric constant 4.3, thickness of 1.6 mm, and size of 28×40 mm². The measured impedance bandwidth is 430 MHz (2.22~2.65 GHz) in the 2.4 GHz WLAN, 450 MHz (3.38~3.83 GHz) in the 3.5 GHz and 2390 MHz (4.95~7.34 GHz), In particular, it has been observed that antenna has a stable omnidirectional radiation patterns as well as gain of 1.537 dBi, 1.878 dBi and 2.337 dBi in the entire frequency band of interest.

• Korean Journal of Optics and Photonics
• /
• v.14 no.6
• /
• pp.600-605
• /
• 2003

We have experimentally demonstrated a Direct Optical Switching (DOS) CDMA for future wide-band mobile communication systems at the 40 ㎓ band by using orthogonal (crosscorrelation $\leq$2) unipolar type codes with code length of 16 and chip rate of 2.5 Gcps for radio-over-fiber (RoF) systems. Pulse-amplitude-equalized 40 ㎓ laser pulses were provided by rational-harmonically mode-locking a 10 ㎓ fiber ring laser.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.41 no.1
• /
• pp.69-72
• /
• 2004

A bandpass filter has been designed by employing the PBG structure and the aperture on the ground together in this paper. The harmonics of band pass filter have been suppressed by employing the PBG structure and the bandwidth of it has been broadened by using the aperture on the ground. The three kinds of PBG structures has been combined to suppress the harmonics of the filter The center frequency of filter is 2.2 GHz and the bandwidth has been increased from $40\%$ by the aperture and all harmonics were suppressed about 35dBc by the PBG. The insertion loss has been reduced 3.0dB to 2.6dB.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.45 no.4
• /
• pp.131-136
• /
• 2008

Two Ka-band 3-stage power amplifiers were designed and fabricated using $0.18-{\mu}m$ CMOS technology. For low loss matching networks for the amplifiers, two substrate-shielded transmission line structures, having good modeling accuracy up to 40 GHz were used. The measured insertion loss of substrate-shielded microstrip-line (MSL) was 0.5 dB/mm at 27 GHz. A 3-stage CMOS amplifier using substrate-shielded MSL achieved a 14.7-dB small-signal gain and a 14.5-dBm output power at 27 GHz in a compact chip area of 0.83$mm^2$. The measured insertion loss of substrate-shielded coplanar waveguide (CPW) was 1.0 dB/mm at 27 GHz. A 3-stage amplifier using substrate-shielded CPW achieved a 12-dB small-signal gai and a 12.5-dBm output power at 26.5 GHz. This results shows a potential of CMOS technology for low cost short-range wireless communication components and system.

• The Journal of Korean Institute of Information Technology
• /
• v.16 no.11
• /
• pp.77-84
• /
• 2018

In this paper, the circular polarization microstrip patch antenna using the T-junction power divider is proposed. The operating frequency of the proposed antenna is ISM band of 2.4GHz and the circular polarization is induced by feeding a phase difference of $90^{\circ}$ in two edges. The structure of the antenna consists of a general patch and a T-junction power divider. Furthermore, to optimize the proposed antenna, it is analyzed the reflection coefficient, the axial ration and the radiation pattern. The impedance bandwidth of the antenna is observed to be 40MHz within a range of 2.39 to 2.43GHz, similarly, the axial ratio bandwidth is observed having the bandwidth of about 12MHz in 2.398 to 2.410GHz range. The radiation pattern of the antenna is seen to be right circular polarization. Furthermore, the gain of the antenna is observed to be 2.04 and 3.4dBic at XZ and YZ-plane, respectively.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.40 no.11
• /
• pp.34-41
• /
• 2003

In this paper, 60GHz band transmitter and receiver for wireless LAN are designed and implemented using the broband amplifier and mixer fabricated by standard 0.1${\mu}{\textrm}{m}$ MIMIC process of MINT. Output power and gain of the RF transmitter are 0 ㏈m and 1.7㏈, respectively. Noise figure and gain of the receiver are 4.2㏈ and l5.7dB, respectively. Considering the sensitivity and LOS test, this system can communicate with BER of below than 10$^{-6}$ at a distance more than 35m. DSSS, which is strong for concealment and disturbance, is adopted.

• Journal of IKEEE
• /
• v.22 no.4
• /
• pp.1050-1055
• /
• 2018

In this paper, we analyzed the sensitivity of matching elements for the dual-band operation of a power amplifier with composite right/left-handed (CRLH) transmission lines. Metamaterial theory enables CRLH transmission to support arbitrary impedance matching at dual frequencies. In general, at sub-GHz range, the CRLH matching networks are commonly implemented with lumped elements, which are prone to manufacturing distribution. In order to reduce the effect from the distribution of element values in design, we suggest a method to analyze the sensitivity of matching elements from the performance aspect of power amplifiers. Based on the analysis, a 40dBm dual-band power amplifier operating at 0.7GHz and 1.5GHz is designed.

• Journal of Satellite, Information and Communications
• /
• v.2 no.2
• /
• pp.64-68
• /
• 2007

This paper describes the development of RF front.end equipment of a wide band high precision satellite navigation receiver to be able to receive the currently available GPS navigation signal and the GALILEO navigation signal to be developed in Europe in the near future. The wide band satellite navigation receiver with high precision performance is composed of L - band antenna, RF/IF converters for multi - band navigation signals, and high performance baseband processor. The L - band satellite navigation antenna is able to be received the signals in the range from 1.1 GHz to 1.6 GHz and from the navigation satellite positioned near the horizon. The navigation signal of GALILEO navigation satellite consists of L1, E5, and E6 band with signal bandwidth more than 20 MHz which is wider than GPS signal. Due to the wide band navigation signal, the IF frequency and signal processing speed should be increased. The RF/IF converter has been designed with the single stage downconversion structure, and the IF frequency of 140 MHz has been derived from considering the maximum signal bandwidth and the sampling frequency of 112 MHz to be used in ADC circuit. The final output of RF/IF converter is a digital IF signal which is generated from signal processing of the AD converter from the IF signal. The developed RF front - end has the C/N0 performance over 40dB - Hz for the - 130dBm input signal power and includes the automatic gain control circuits to provide the dynamic range over 40dB.