• The Journal of the Convergence on Culture Technology
• /
• v.9 no.1
• /
• pp.525-530
• /
• 2023

Although double-stage hanger is used in many homes for its space utilization and ease of installation, it is inconvenient for users to take off clothes hung on the upper bar due to its high height. Therefore, this paper proposes a new type of double-stage hanger that allows users to easily hang or take out clothes hung on the upper bar while maintaining the function of the existing double-stage hanger. 4-bar link mechanism is applied so that the upper bar can come down to a convenient height with one operation. In addition, an appropriate link shape, length, and joint type are selected so that the height is adjusted three-dimensionally to prevent overlapping of clothes hanging on upper/lower bars. FEA analysis is performed to ensure that the presented hanger shape can support the load of clothes during height adjustment and the feasibility of the three-dimensional height adjustment hanger is verified through fabrication.

• Aerospace Engineering and Technology
• /
• v.4 no.1
• /
• pp.25-30
• /
• 2005

The 4-bar linkage is the simplest model for the simulation of a retractable landing gear. In general, a designer uses a commercial software to design a linkage, which requires tedious iterations to obtain a good solution. By applying synthesis methodology the iteration process can be reduced remarkably. However, most of solutions obtained using synthesis process may not be an optimized solution. In this study, the characteristics of the optimization solution domain has been analyzed so that an optimization process can be adapted easily to a synthesis process.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.16 no.5
• /
• pp.910-923
• /
• 1992

Experimental verification of numerical results is conducted by measuring the dynamic strains of mid-points of the coupler and the lever for the 4-bar linkage mechanism with rigid bearing and flexible bearing, respectively. For the axial strain of lever mid-point, the numerical results including geometric stiffness almost agree with the experimental ones, however, the numerical results excluding geometric stiffness almost agree with the experimental ones for the axial strain of coupler mid-point. It is supposed that these phenomena should be caused by the fact that the motion of the coupler is more complicated than of the lever. The signals of dynamic strains of coupler and lever mid-points, measured by strain gages, are transformed into frequency domain by fast fourier transformer. From this experiment, the lst resonance frequencies of the coupler and the lever are obtained. It is made clear that the former almost agrees with the fundamental and the latter the 2nd mode natural frequency of the mechanism system calculated by numerical analysis.

• The Journal of the Convergence on Culture Technology
• /
• v.10 no.1
• /
• pp.459-464
• /
• 2024

The purpose of this study is to design a toilet lifting seat to prevent falls accidents in the elderly while using the toilet. Prior to design, laws and national standards related to restroom use were investigated and the available space for the assistive devices to be installed was determined. In additions, considering the body size and operating range of the elderly, the optimal final position of the toilet seat is set so that users can use it more safely and conveniently without external help. Moreover, in order to provide an effective standing assistance function, a complex 4-bar link structure was applied to enable simultaneous seat elevation and angle adjustment when operating the device, and the appropriate link shape and dimensions were determined using a linkage program and UG NX. FEA analysis using ANSYS Workbench is performed to ensure the robustness of the stretched linkage and the feasibility of the lifting seat is verified through fabrication.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.21 no.2
• /
• pp.159-164
• /
• 2011

In this study, a crab robot is implemented in H/W based on four-bar linkage mechanism and Jansen mechanism, and its kinematics is analysed. A vision camera is attached to the mechanism, which makes the proposed robot a kind of biologically inspired robot for image acquisition. Three ultrasonic sensors are adopted for obstacle avoidance. In addition, the biologically inspired robot can achieve the mission appointed by a programmer outside, based on RF and Blue-tooth communication module. For the design and implementation of a crab robot, it is need to get joint variable, a foot point, and their relation. Thus, the proposed kinematic analysis is very important process for the design and implementation of legged robots.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2012.10a
• /
• pp.209-210
• /
• 2012

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2010.05a
• /
• pp.541-542
• /
• 2010

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• v.10 no.2
• /
• pp.21-25
• /
• 2005

• Journal of the Korean Society for Precision Engineering
• /
• v.30 no.9
• /
• pp.961-968
• /
• 2013

In this paper, we propose an optimal design for starfish capturing manipulator module with four-bar linkage mechanism. A tool link with compliance is attached on the four-bar linkage, and the tool repeats detaching starfish from the ground and putting it into the storage box. Since the tool is not rigid and the manipulator is operating underwater, the trajectory of the tool tip is determined by its dynamics as well as kinematics. We analyzed the trajectory of the manipulator tool tip by quasi-static analysis considering both kinematics and dynamics. In optimization, the lengths of each link and the tool stiffness are considered as control variables. To maximize the capturing ability, capturing stroke of the four-bar manipulator trajectory is maximized. Reaction force and reaction moment, and other kinematic constraints were considered as inequality constraints.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2002.05a
• /
• pp.524-527
• /
• 2002

This paper is on the development of an educational 6-axis articulated manipulator using 4-bar linkage system. Especially, the 2$^{nd}$ and the 3$^{rd}$ axes need large torque to control the movement of an end-effect. However, small motors (RC-servo, DC-gear, stepping meters) are used for the 4-bar linkage. In addition the manipulator can be operated by a switch and also motion can be realized automatically, based on C-language coded users programs..