• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2001.04a
• /
• pp.351-358
• /
• 2001

In this study, for the investigation of effects of several parameters, such as fluid mesh boundary size, cylinder or block shape, dimensions of depth, breadth and length at free suface, and fluid mesh element size to the depth direction on a reliable shock response of finite element model under underwater explosion with consideration of the bulk cavitation analysis of a simplified surface ship was carried out using the LS-DYNA3D/USA code. The shock responses were not much affected by the fluid mesh parameters. The computational time was greatly dependent on the number of DAA boundary segments. It is desirable to reduce the DAA boundary segments in the fluid mesh model, and it is not necessary to cover the fluid mesh boundary to or beyond the bulk cavitation zone just for the concerns about an initial shock wave response. It is also the better way to prefer cylinder type of the fluid mesh model to the block one.

• Ocean Systems Engineering
• /
• v.1 no.1
• /
• pp.73-93
• /
• 2011

Large deck openings of ultra large container ships reduce their torsional stiffness considerably and hydroelastic analysis for reliable structural design becomes an imperative. In the early design stage the beam model coupled with 3D hydrodynamic model is a rational choice. The modal superposition method is ordinary used for solving this complex problem. The advanced thin-walled girder theory, with shear influence on both bending and torsion, is applied for calculation of dry natural modes. It is shown that relatively short engine room structure of large container ships behaves as the open hold structure with increased torsional stiffness due to deck effect. Warping discontinuity at the joint of the closed and open segments is compensated by induced distortion. The effective torsional stiffness parameters based on an energy balance approach are determined. Estimation of distortion of transverse bulkheads, as a result of torsion and warping, is given. The procedure is illustrated in the case of a ship-like pontoon and checked by 3D FEM analysis. The obtained results encourage incorporation of the modified beam model of the short engine room structure in general beam model of ship hull for the need of hydroelastic analysis, where only the first few natural modes are of interest.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.10 no.2
• /
• pp.180-187
• /
• 2018

Corrugated bulkhead has been adopted for cargo tank bulkheads of commercial vessels such as bulk carriers, product oil carriers and chemical tankers. It is considered that corrugated bulkhead is a preferred structural solution, compared to the flat stiffened bulkhead, due to several advantages such as lower mass, easier maintenance and smaller corrosion problems. Many researches to find the optimum shape of corrugated bulkhead have been mostly carried out for bulk carriers. Compared to corrugated bulkheads of bulk carriers, ones of chemical tankers are more complicated since they are composed of transverse and longitudinal bulkheads, and they are made of higher priced materials. The purpose of this study is the development of minimum weight design method for corrugated bulkhead of chemical tankers. Evolution strategy is applied as an optimization technique. It has been verified from many researches that evolution strategy searches global optimum point prominently by using multi-individual searching technique. Multi-individual searching methods need excessive time if they connect to 3-D finite element model for repetitive structural analyses. In order to resolve this issue, 2-D beam element connected to deck and lower stool is substituted for a corrugated structure in this study. To verify the reliability of the structural responses by idealized 2-D beam model, they have been compared with ones by 3-D finite element model. In this study, optimum design for corrugated bulkhead of 30 K chemical tanker has been carried out, and the results by developed optimum design program have been compared with design data of existing ship. It is found out that optimum design is about 9% lighter than one of existing ship.

• Computational Structural Engineering
• /
• v.5 no.2
• /
• pp.79-85
• /
• 1992

For the structural analysis of optimum form decision of 3-D free form structure such as ship, plane, automobile, definition of versatile forms and comparision between them satisfying the design criterion, is essential. In this paper, 3-D free form structure and it's variation are defined and attempts were made to obtain geometric form information for structural analysis. The validity of the method has been tested for a particular free model selected.

• Journal of the Society of Naval Architects of Korea
• /
• v.54 no.6
• /
• pp.515-521
• /
• 2017

Large Cavitation Tunnel (LCT) of KRISO enables us to conduct cavitation tests of the propeller attached to a ship model. As the ship model tests are done at rather high Reynolds number of 107~108, flow measurement system such as pitot tube cannot be employed because of structural safety problems in its system and difficulties in installing it within the test section. Thus, KRISO has developed new 3-D LDV system used in large test section of LCT. There are several difficulties in using 3-D LDV, which did not allow efficient operation of it. The first trouble was the calibration using the conventional pin hole. To make the focus with same laser-beam waists at the wanted position, the high spatial resolution CCD is utilized in the calibration procedure for 3-D LDV. The off-axis configuration provides two velocity components in the horizontal plane and on-axis configuration gives third velocity component in the vertical plane. The horizontal velocity components are also obtained in the coincidence mode, which prevents any misleading results in the off-axis configuration. The nominal wake of Aframax tanker model is measured by the developed 3-D LDV system. The measured hull wake showed good agreement with that obtained by CFD calculation.

• Bulletin of the Society of Naval Architects of Korea
• /
• v.26 no.4
• /
• pp.57-66
• /
• 1989

In this paper, a theory for the static analysis of large plastic deformations of 3-dimensional frames, aiming at application to the collapse analysis of ship structures, is presented. In the frame analysis formulation, effects of shear deformations are included. A plastic hinge is inserted into the field of a beam end, and post. failure deformation of the plastic hinge is characterized by finite rotations and extensions. In order to model deep web frames of ship's structures into a framed structures, collapse of thin-walled plate girders is investigated. The proposed analysis method is applied to several ship structural models in the references.

• Journal of Ocean Engineering and Technology
• /
• v.33 no.1
• /
• pp.33-41
• /
• 2019

Estimating fatigue damage is a very important issue in the design of ships. The springing and whipping response, which is the hydro-elastic response of the ship, can increase the fatigue damage of the ship. So, these phenomena should be considered in the design stage. However, the current studies on the the application of springing and whipping responses at the design stage are not sufficient. So, in this study, a prediction method was developed using fluid-structural interaction analysis to assess of the fatigue damage induced by springing and whipping. The stress transfer function (Stress RAO) was obtained by using the 3D FE model in the frequency domain, and the fatigue damage, including linear springing, was estimated by using the wide band damage model. We also used the 1D beam model to develop a method to estimate the fatigue damage, including nonlinear springing and whipping by the vertical bending moment in the short-term sea state. This method can be applied to structural members where fatigue strength is weak to vertical bending moments, such as longitudinal stiffeners. The methodology we developed was applied to 325K VLOC, and we analyzed the effect of the springing and whipping phenomena on the existing design.

• Journal of the Society of Naval Architects of Korea
• /
• v.45 no.6
• /
• pp.710-718
• /
• 2008

This paper presents a simple and fast approach to plan the arrangement of supports and to do a ship docking analysis. The unpredicted structural damages often happen from a docking works as the size of ships are getting larger and larger. In docking a ship, excessive reaction forces from supports are primary causes of the structural damage. The grillage analysis method is employed to simply calculate only the reaction forces at supports. The grillage modeling strategies are proposed to improve the accuracy. In this paper, the results obtained by the proposed approach are compared with those of the current whole-ship FEA for typical types of ships. Comparison shows that the results from the present grillage approaches are reasonably in a good agreement with the 3-D full F.E one. Finally, an integrated program developed for the ship docking analysis is described.

• Journal of the Society of Naval Architects of Korea
• /
• v.42 no.3
• /
• pp.284-289
• /
• 2005

A structural design system is developed for the optimum design of double hull tankers based on the multi-objective function method. As a multi-objective function method, Pareto optimal based random search method is adopted to find the minimum structural weight and fabrication cost. The fabrication cost model is developed by considering the welding technique, welding poses and assembly stages to manage the fabrication man-hour and process. In this study, a new structural design is investigated due to the rapidly increased material cost. Several optimum structural designs on the basis of high material cost are carried out based on the Pareto optimal set obtained by the random search method. The design results are compared with existing ship, which is designed under low material cost.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 1991.04a
• /
• pp.43-47
• /
• 1991

For the structural analysis of optimum form decision of 3-D free fort structure such as ship, plane, automobile, definition of versatile forms and comparision between them satisfying the design criterion, is essential. In this paper, three dimensional free-form structure and it's variation are defined and attempts were made to obtain geometric form information for structural analysis. The validity of the method ks been tested for a particular free-form model selected.