• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.48 no.2
• /
• pp.119-125
• /
• 2020

A high Reynolds number transonic wind tunnel has been built in 2018 at Agency for Defense Development(ADD). The tunnel has a closed circuit with a 1.5m×1.5m test section and is injection driven from a 140bar air supply system. The Mach number range is 0.3-1.2 with a conventional contracting nozzle and 1.4 with a convergent-divergent contraction. The stagnation pressure range is 100-550kPa at the lowest Mach number. An AGARD-B standard model is tested in the transonic wind tunnel to obtain 6-DOF aerodynamic coefficients. The results are compared with those obtained from ADD trisonic wind tunnel and others. We verify that the transonic wind tunnel become available to develop an aircraft from the testing results.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.48 no.3
• /
• pp.175-185
• /
• 2020

The six-DOF aerodynamic coefficients of a missile entail inherent physical gradient constraints originated from the geometric characteristics of a cylindrical fuselage. To effectively adopt the freely available gradient information in aerodynamic coefficients modeling, this research employed gradient-enhanced (GE) Gaussian process. To investigate the accuracy of aerodynamic coefficients predicted with gradients information, we compared two Gaussian-process-based models: ordinary and GE Gaussian process models with and without gradient information, respectively. As a result, we found that GE Gaussian process models were able to comply with imposed gradient information and more accurate than ordinary Gaussian process models. However, we also found that GE Gaussian process modeling cannot handle gradient information continuously and ends up with more samples due to additional gradient information.

• Journal of the Korean Society for Precision Engineering
• /
• v.34 no.1
• /
• pp.41-46
• /
• 2017

Magnetically levitated (Maglev) vehicles maintain a constant air gap between guideway and car bogie, and thereby achieves non-contact riding. Since the straightness and the flatness of the guideway directly affect the stability of levitation as well as the ride comfort, it is necessary to monitor the status of the guideway and to alert the train operators to any abnormal conditions. In order to develop a signal processing algorithm that extracts guideway irregularities from sensor data, virtual testing using a simulation model would be convenient for analyzing the exact effects of any input as long as the model describes the actual system accurately. Simulation model can also be used as an estimation model. In this paper, we develop a state-space dynamic model of a maglev vehicle system, running on the guideway that contains jumps. This model contains not only the dynamics of the vehicle, but also the descriptions of the power amplifier, the anti-aliasing filter and the sampling delay. A test rig is built for the validation of the model. The test rig consists of a small-scale maglev vehicle, tracks with artificial jumps, and various sensors measuring displacements, accelerations, and coil currents. The experimental data matches well with those from the simulation model, indicating the validity of the model.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.9 no.6
• /
• pp.1395-1401
• /
• 2005

Mobile manipulator is a robot that has mobility and manipulability with the combination of the task robot and mobile robot. One of the most important feature of the Mobile Manipulator is redundant freedom. Using the redundant freedom, Mobile Manipulator can move various mode, perform dexterous motion. It can have the wider workspace and better performance in avoidance of singularity and obstacle than the fixed base structured robot. Cooperation control using the Mobile Manipulator improves the performance of the robot with redundant freedom in workspace. In this paper, configuration control of the Mobile Manipulator has been studied using Task Segment and TOMM(Task-Oriented Manipulability Measure). For verifying the proposed algorithm, we implemented a mobile manipulator, PURL-II, which is composed of a mobile robot with 3DOF and a task robot with SDOF.

• Journal of the Korea Convergence Society
• /
• v.3 no.4
• /
• pp.35-44
• /
• 2012

In this study, a simulation program is developed in order to investigate non steady-state cornering performance of 6WD/6WS special-purpose vehicles. 6WD vehicles are believed to have good performance on off-the-road maneuvering and to have fail-safe capabilities. But the cornering performances of 6WS vehicles are not well understood in the related literature. In this paper, 6WD/6WS vehicles are modeled as a 18 DOF system which includes non-linear vehicle dynamics, tire models, and kinematic effects. Then the vehicle model is constructed into a simulation program using the MATLAB/SIMULINK so that input/output and vehicle parameters can be changed easily with the modulated approach. Cornering performance of the 6WS vehicle is analyzed for brake steering and pivoting, respectively. Simulation results show that cornering performance depends on the middle-wheel steering as well as front/rear wheel steering. In addition, a new 6WS control law is proposed in order to minimize the sideslip angle. Lane change simulation results demonstrate the advantage of 6WS vehicles with the proposed control law.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2005.10a
• /
• pp.55-61
• /
• 2005

A rudder roll control system is developed and analyzed to control yawing and rolling motion of ship in irregular waves. The 4-DOF maneuvering equations of motion are derived to carry out the simulation of the motion of a ship and the wave forces are considered as the external forces of a ship in the simulation. The wave forces in the time domain analysis are generated from the frequency transfer function calculated by 3-D source distribution method. The rudder roll control system is developed by linear combination of PD rudder controllers of yawing and rolling motion Rudder rate speed and Schilling rudder are considered to increase roll reduction efficiency.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.37 no.3
• /
• pp.232-239
• /
• 2009

The prediction of the separation trajectories of external stores carried by military aircraft is an important task in the area of aircraft design having the objective to define the operational, release envelopes. This paper presents the results obtained for safe store separation from a fighter aircraft by experimental methods in the subsonic wind tunnel. The problems associated with separation of external stores can be studied by the use of several wind-tunnel test techniques. Attention is given the two most useful techniques: 1) dynamically scaled drop-model testing, 2) grid testing. A description of each method is given and data obtained are shown to validate the similarity within acceptable limits.

• Journal of the Korean Society for Precision Engineering
• /
• v.22 no.5 s.170
• /
• pp.103-112
• /
• 2005

This paper presents one-axis high precision scanning system and illustrates the design of modified $X-Y-{\theta}$ stage as a tracker using VCM and commercialized air bearings for it. The scanning system for 100nm resolution is composed of the 3-axis stage and one axis long stroke linear motor stage as a follower. In this study a previous proposed and presented structure of VCM for the fine stage is modified. The tracker has 3 DOF($X-Y-{\theta}$ motions by four VCM actuators which are located on the same plane. So 4 actuating forces are suggested and designed to create least pitch and roll motions. This article will show about the design especially about optimal design. The design focus of this fine stage is to have high acceleration to accomplish high throughput. The optimal design of maximizing acceleration is performed in restrained size. The most sensitive constraint of this optimal design is heat dissipation of coil. There are 5 design variables. Because the relationship between design variables and system parameters are quite complicated, it is very difficult to set design variables manually. Due to it, computer based optimal design procedure using MATLAB is used. Then, this paper also describes the procedures of selecting design variables for the optimal design and a mathematical formulation of the optimization problem. Based on the solution of the optimization problem, the final design of the stage is also presented. The results can be verified by MAXWELL. The designed stage has the acceleration of about 5 $m/s^{2}$ with 40kg total mass including wafer chuck and interferometer mirror. And the temperature of coil is increased $50^{\circ}C$. In addition, the tracker is controlled by high precision controller system with HP interferometer for it and linear scaler for the follower. At that time, the scanning system has high precision resolution about 5nm and scanning resolution about 40nm in 25mm/s constant speed

• Journal of the Korean Society of Propulsion Engineers
• /
• v.22 no.4
• /
• pp.1-11
• /
• 2018

A system design and integrated design process for a space launch vehicle were established based on system engineering. With the mission design results for a given payload weight and trajectory, it is possible to perform optimal design by integrating each unit such as propulsion, weight estimation, and aerodynamic force after analysis, during in the system design process. The program is finally configured to verify that the designed vehicle can perform its mission through 3-DOF trajectory optimization simulation. Genetic algorithms are used as the optimization method, and the optimal design results of the variables and parameters to be considered during design are presented.

• Journal of agriculture & life science
• /
• v.52 no.6
• /
• pp.127-138
• /
• 2018

In this study, the operational characteristics of a domestic vegetable transplanter were investigated. The main functional components and power path of the tranplanter were analyzed. The link structure of transplanting device waskinematically analyzed, and 3D modeling and dynamic simulation were performed. Based on this analysis, the trajectory of the bottom end of the transplanting hopper was analyzed. Also, the plant spacing according to the engine speed and the shifting stage of transplanting transmission was analyzed and verified by field test. As main results of this study, the transplanting device is one degree of freedom(DOF) 4-bar link type mechanism which comprises 10 links and 13 rotating joints. The transplanting hopper plants seedlings in a vertical direction while maintaining a constant posture by the links of transplanting device. The power is transmitted to both the driving part and transplanting part from the engine, and the maximum and minimum plant spacing of the transplanting device were 428.97 mm and 261.20 mm.