• Proceedings of the KIEE Conference
• /
• 2007.10c
• /
• pp.65-67
• /
• 2007

In this paper describes the design and characteristic analysis of a novel 2-DOF(Degree of Freedom) motor. For multi DOF actuating, several numbers of motors have been used. But the using of normal motors they connected each other in single joint, have necessary to a several type of complex power transmission devices. The 2-DOF motor can drive pan, tilt motion in only one unit and it is not necessary to use additional gears and links parts. Therefore by the using of 2-DOF spherical motor ran eliminate; combined effects of inertia, backlash, non-linear friction, and elastic deformation of gears. The validity of the analysis is confirmed by 3D finite element method.

• Proceedings of the KIEE Conference
• /
• 2005.10b
• /
• pp.255-257
• /
• 2005

This paper deals with the design and the realization of a small humanoid robot, which is called SERO_VI. The design concept and the mechanical structure including kinematics for the robot are presented. The humanoid robot consisted of 25 DOF with legs 12 DOF, arms 8 DOF, waists 3 DOF and heads 2 DOF for the purpose of vision system. The controller structure was also suggested such as modular joint actuators, DSP interface and their communication method. Simple experiment was done and its validness was investigated in order to verify the kinematic result.

• Journal of Power System Engineering
• /
• v.11 no.3
• /
• pp.59-65
• /
• 2007

In this study, 6-DOF simulator using pneumatic cylinder driving apparatus was manufactured because a pneumatic cylinder driving apparatus is superior to electric driving motor and hydraulic actuator, which used in traditional 6-DOF simulator, in competitive price and acceleration performance, and, 6-DOF motion can be realized at a low price in case that relatively low load is imposed on the simulator. The possible range of pose control of the simulator was investigated by inverse kinematics, and, it was controlled by a linear controller derived from linear model of the simulator. The Experimental results show that the simulator follows given coordinate well.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.4 no.5
• /
• pp.455-461
• /
• 1999

In this paper, we present the 3DOF force-rei1ecting interface which allows to acquire force of objc'Ct within a a virtual environment. This system is comlxlsed of device, virtual environment model, and force-rei1ecting r rendering algorithm. We design a J DOF force reflecting device using the pc$\alpha$allel linkage, torque shared by W wire, and the controller of system applied by impedance control algorithm. The force reflecting behaviour i implemented as a function position is equivalent to controlling the mechanical impedance felt by the user. E Especially how force should be supplied to user, we know using a God-Object algorithm As we experiment a system implement$\varepsilon$d by the interface of 3D virtual object and 3DOF force reJll'Cting i interface, we can feel a contact, non contact of :)D virtual object surface and sensin앙 of push button model.utton model.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.20 no.12
• /
• pp.3883-3891
• /
• 1996

Performance and productivity of robot manipulator can be improved by increasing its working speed and extending its link length. But heavy weght of the commercial robot links, considered as "rigid body", limits its mazimum working speed and the weght of the links can be reduced for high speed operation. But this light-weight link or long link for special use cannot be consideredas "rigid" structure and vibration of the link due to its flexibility causes errors in end-effector position and orientation. Thus the elastic behaviro of the flexible link should be taken care of for increasing work speed and getting smaller error of end-effector position. In this paper, the fuzzy control theory is selected to design the controller which controlos the joint positions of the robot manipulator and suppress the vibration of flexible link. In the forst place, for the 1 DOF flexible link system, the fuzzy control theory is implemented. The contdroller for the 1 DOF flexible link system is designed. Experimental research is carried out to examine the controllability and the validity of the fuzzy control theory based controller. Next, using the extended desing schemes for the case of the 1 DOF flexible link system and usign the experimental phenomena of the 3 DOF flexible link system, the fuzzy controller for the 3 DOF flexible link system is desinged and experimented.ed and experimented.

• Journal of the Korean Society for Precision Engineering
• /
• v.34 no.2
• /
• pp.107-114
• /
• 2017

In this investigation, we describe a metrological technique for surface and thickness profiles of a silicon (Si) wafer by using a 6 degree of freedom (DOF) stitching method. Low coherence scanning interferometry employing near infrared light, partially transparent to a Si wafer, is adopted to simultaneously measure the surface and thickness profiles of the wafer. For the large field of view, a stitching method of the sub-aperture measurement is added to the measurement system; also, 6 DOF parameters, including the lateral positioning errors and the rotational error, are considered. In the experiment, surface profiles of a double-sided polished wafer with a 100 mm diameter were measured with the sub-aperture of an 18 mm diameter at $10\times10$ locations and the surface profiles of both sides were stitched with the sub-aperture maps. As a result, the nominal thickness of the wafer was $483.2{\mu}m$ and the calculated PV values of both surfaces were $16.57{\mu}m$ and $17.12{\mu}m$, respectively.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.26 no.3
• /
• pp.117-125
• /
• 2022

In this study, centrifuge model tests were performed to evaluate the seismic response of multi-DOF structures with shallow foundations. Also, elastic time history analysis on the fixed-base model was performed and compared with the experimental results. As a result of the centrifuge model test, earthquake amplification at the fundamental vibration frequency of the soil (= 2.44 Hz) affected the third vibration mode frequency (= 2.50 Hz) of the long-period structure and the first vibration mode (= 2.27 Hz) of the short-period structure. The shallow foundation lengthened the periods of the structures by 14-20% compared to the fixed base condition. The response spectrum of acceleration measured at the shallow foundation was smaller than that of free-field motion due to the foundation damping effect. The ultimate moment capacity of the soil-foundation system limited the dynamic responses of the multi-DOF structures. Therefore, the considerations on period lengthening, foundation damping, and ultimate moment capacity of the soil-foundation system might improve the seismic design of the multi-DOF building structures.

• Journal of Institute of Control, Robotics and Systems
• /
• v.5 no.8
• /
• pp.977-989
• /
• 1999

The purpose of this study is to analyze how the human body having more muscles than its degree-of-freedom modulates an effective stiffness using redundant actuation, and to apply this concept to the design and control of advanced machines which requires adaptable spring. To investigate the adaptable stiffness phenomenon due to redundant actuation in the human body, this paper derives a general stiffness model of the Human body. In particular, for a planar 1 DOF human arm model, a planar 2 DOF human arm model, a spherical 3 DOF shoulder model, a 4 DOF human arm model, and a 7 DOF human arm model, the required nonlinear geometry ad the number of required actuator for successful modulation of the effective stiffness are analyzed along with a load distribution method for modulation of the required stiffness of such systems. Secondly, the concept of motion frequency modulation is introduced to show the usefulness of adaptive stiffness modulation. The motion frequency modulation represents a control of stiffness and / or inertia properties of systems. To show the effectiveness of the proposed algorithm, simulations are performed for 2 DOF anthropomorphic robot.

• Journal of the Korean Society for Precision Engineering
• /
• v.34 no.1
• /
• pp.53-58
• /
• 2017

A fine stage is developed for the 3-DOF error compensation of a linear axis in order to improve the positioning accuracy. This stage is designed as a planar parallel mechanism, and the joints are based on a flexure hinge to achieve ultra-precise positioning. Also, the effect of Abbe's offsets between the measuring and driving coordinate systems is minimized to ensure an exact error compensation. The mode shapes of the designed stage are analyzed to verify the desired 3-DOF motions, and the workspace and displacement of a piezoelectric actuator (PZT) for compensation are analyzed using forward and inverse kinematics. The 3-DOF error of a linear axis is measured and compensated by using the developed fine stage. A marked improvement is observed compared to the results obtained without error compensation. The peak-to-valley (PV) values of the positional and rotational errors are reduced by 92.6% and 91.3%, respectively.

• Journal of Electrical Engineering and Technology
• /
• v.8 no.1
• /
• pp.90-96
• /
• 2013

As the need of electric motor is increased rapidly throughout our society, the various application fields are created and the service market called robot gets expanded as well as the existing industrial market. Out of those, the joint systems such as humanoid that is servo actuator for position control or all fields which require multi-degree of freedom (multi-DOF) require the development of innovative actuator. It is multi-DOF spherical motor that can replace the existing system in multi-DOF operating system. But, multi-DOF spherical motor that has been researched up to date is at the stage which is insufficient in performance or mechanical practicality yet. Thus, first of all the research results and limitation of the previously-researched guide frame-type spherical motors were analyzed and then the feature of double air-gap spherical motor which was devised to complement that was studied. The double air-gap multi-DOF spherical motor is very suitable spherical motor for system applying which requires the multi-DOF operation due to its simple structure that does not require other guide frame as well as performance improvement due to its special shape which has two air-gaps. So, the validity of the study was verified by designing and producing it with 3D-FEM through the exclusive jig for multi-DOF spherical motor.