• Journal of the Korean Society for Heat Treatment
• /
• v.3 no.3
• /
• pp.13-20
• /
• 1990

SCM 21 and D.P steel were carburized in vacuum using prophane at a temperature ranging from 1228k to 1308k under a gas pressure ranging from 21.3kpa to 61.8kpa, and the following results were obrained. 1) D.P. steel has considerable efficiency in depressing the grain growth during the high temperature carburizing and it has fine structure even at 1268k for 14.4ks when carburizied. Therefore this steel is expected to be suitable for vacuum carburizing at a high temperature. 2) Case depth was increased as the carburizing temperature increases and it was 3.2mm at max, temperature of 1308k, for max, time of 14.4ks and under max, pressure of 61.8kpa. Thus vacuum-carburizing was considered effective for the materials which need case depth, which is necessary for machine structure use. 3) The rate of case depth of SCM 21 was faster than D.P. steel under same carburizing conditions and the increasing rate of the case depth was constant. 4) Case depth was increased as the gas pressure becomes high under same carburizing temperature. 5) Case carbon concentration, $C_s$, of SCM 21 obeys to a formula, $$C_s=kt^{1/2}+C_0$$ Where k is $2.15{\times}10^{-2}$($wt%.S^{-1/2}$) and this value is a little bit lower than that of SNCM 815.

• Nuclear Engineering and Technology
• /
• v.29 no.3
• /
• pp.260-268
• /
• 1997

The effects of three mechanisms, calcium depletion, sulphate and carbonate penetration, on the concrete degradation have been studied. The shrinking core model (SCM) and the HYDROGEOC. HEM (HGC) model have been applied to evaluate how fast the mechanisms proceed. The SCM is an analytical approximation model and the HGC is a numerical mass transport model coupled with chemical reaction. The SCM leads to more conservative results than the HGC, and turns out to be very useful in the viewpoint of simplicity and conservatism. During 300 years, calcium has been depleted within 10 cm from the concrete outer surface, and sulphate has penetrated less than 13.5 cm into the concrete. Carbonate has not penetrated own 7 cm into the concrete in contact with the bentonite, and, furthermore, its penetration into the concrete with the groundwater is negligible. Conclusively, the concrete is expected to maintain its integrity for at least 300 years that are regarded as institutional control period of intermediate and low-level radioactive waste repository.

• Journal of the Korean Electrochemical Society
• /
• v.13 no.3
• /
• pp.198-202
• /
• 2010

Lithium co-polyelectrolyte-ionic liquid systems, using poly (lithium 2-acrylamido-2-methyl propanesulfonate; PAMPSLi) and polyvinyl formamid (PVF) were prepared and their electrochemical and physical properties were measured. The conductivity of co-polymer systems, PAMPSLi/PVF/N, N-dimethyl-N-propyl-N-butylammonium tricyanomethanide (PAMPSLi/PVF/$N_{1134}$TCM) and PAMPSLi/PVF/N, N-dimethyl-N-propyl-N-butylammonium dicyanamide (PAMPSLi/PVF/$N_{1134}$DCA) exhibited low viscosity ($N_{1134}$TCM:$N_{1134}$DCA 28.6cP, 28.7cP) and higher conductivity ($2.48{\times}10^{-3}Scm^{-1}$, $2.2{\times}10^{-3}Scm^{-1}$) than homopolymer system. The ionic conductivity PAMPSLi/PVF/1-ethyl-3-methyl imidazolium dicyanamide (PAMPSLi/PVF/emImDCA) exhibited $1.54{\times}10^{-3}Scm^{-1}$ and low viscosity (emImDCA: 28.09cP). High flexibility of imidazolium cation and dissociation of lithium cation from the co-polymer chains were affected by high conductivity and low viscosity.

• Journal of Information Technology Services
• /
• v.3 no.1
• /
• pp.89-99
• /
• 2004

Mobile service, which is related to all stages of supply chain, can enhance the efficiency of perception and response of the participants. The advantage of mobile service is ubiquity, speed, traceability, positioning, personalization and safety. The purpose of this paper is to propose an overall framework utilizing mobile service in SCM. In the areas of inventory management, remote diagnostics, communications with field workers, and order fulfillment, customer-centric mobile supply web is proposed and implemented for the wireless warehousing and replenishment system.

• Transactions of Materials Processing
• /
• v.28 no.6
• /
• pp.321-327
• /
• 2019

In this study, a hot and cold forging process was investigated to produce a complex-shaped hub of dual clutch transmission with low material loss and high productivity. The process was designed by the commercial finite element (FE) analysis program, DEFORM-2D (hot forging) and 3D (cold forging). And, the material flow and ductile fracture characteristics were studied to check the surface crack initiation of the specimen. The simulation results indicated that the proposed process could manufacture the complex-shaped hub with no surface crack and high-efficiency compared to the conventional machining process. For verification the numerical results, the hub of the SCM440 was fabricated by the proposed process and the mechanical properties and microstructure evolution were studied. It was demonstrated that the suggested hot and cold forging process might be useful in producing the key components of the automobile industry as a high-efficiency and environmentally friendly process.

• Journal of the Korean Applied Science and Technology
• /
• v.32 no.1
• /
• pp.56-61
• /
• 2015

In this study, the current-voltage curves for the SCM440 steel by the addition of an organic corrosion inhibitor triethanolamine(TEA) was measured using the conventional three electrodes of cyclic voltammetry. As a result, the C-V characteristics of SCM440 steel were to be for an irreversible process due to the oxidation current from the cyclic voltammetry. Diffusion coefficient according to the twice increasing the concentration of TEA in the corrosion inhibitor from $2.5{\times}10^{-4}M$ to $5.0{\times}10^{-4}M$, the diffusion coefficient was found to be a good corrosion-inhibiting effect is reduced by 1.5 times, so for each $2.561{\times}10^{-6}cm^2s^{-1}$ to $1.707{\times}10^{-6}cm^2s^{-1}$. When according to the electrolyte concentration and the effect is to increase the electrolyte concentration to 1.0 N at 0.5 N, the diffusion coefficient is $2.56{\times}10^{-6}cm^2s^{-1}$ to $5.12{\times}10^{-6}cm^2s^{-1}$, each 2 times decrease in the use of the electrolyte of 1.0 N, because this was more appropriate.

• The Journal of the Acoustical Society of Korea
• /
• v.39 no.2
• /
• pp.120-130
• /
• 2020

This paper solves the problem in underdetermined convolutive mixture by improving the disadvantages of the multichannel nonnegative matrix factorization technique widely used in blind source separation. In conventional researches based on Spatial Covariance Matrix (SCM), each element composed of values such as power gain of single channel and correlation tends to degrade the quality of the separated sources due to high variance. In this paper, level and frequency normalization is performed to effectively cluster the estimated sources. Therefore, we propose a novel SCM and an effective distance function for cluster pairs. In this paper, the proposed SCM is used for the initialization of the spatial model and used for hierarchical agglomerative clustering in the bottom-up approach. The proposed algorithm was experimented using the 'Signal Separation Evaluation Campaign 2008 development dataset'. As a result, the improvement in most of the performance indicators was confirmed by utilizing the 'Blind Source Separation Eval toolbox', an objective source separation quality verification tool, and especially the performance superiority of the typical SDR of 1 dB to 3.5 dB was verified.

• Journal of the Korean Society of Industry Convergence
• /
• v.25 no.4_2
• /
• pp.699-706
• /
• 2022

In this study, Directed energy deposition (DED) among additive manufacturing is applied to repair damaged spindle key parts of planner miller. The material of the spindle key is SCM415, and the P21 Powder is used. In order to find the optimal deposition conditions for DED equipment, a single-line deposition experiment is conducted to analysis five parameters. The laser power affects the width, and the height is a parameter affected by coaxial gas and powder gas. In addition, laser power, powder feed rate, coaxial gas, and powder gas are parameters that affect dilution. Otimal deposition is that 400 W of laser power, 4.0 g/min of powder feed rate, 6.5 L/min of coaxial gas, 3.0 L/min of powder gas and 4.5 L/min of shield gas. By setting the optimum conditions, a uniform deposition cross section in the form of an ellipse can be obtained. Damage recovery process of spindle key consists of 3D shape design of the base and deposition parts, deposition path creation and deposition process, and post-processing. The hardness of deposited area with P21 powder on the SCM415 spindle key is 336 HV for the surface of the deposition, 260 HV for the boundary area, and 165 HV for the base material.

• Journal of Sasang Constitutional Medicine
• /
• v.19 no.2
• /
• pp.30-39
• /
• 2007

1. Objectives The Face is an important standard for the classification of Sasang Constitution. We are developing 3D Automatic Face Recognition Apparatus(3D-AFRA) to analyse the facial characteristics. This apparatus show us 3D image and data of man's face and measure facial figure data. So we should examine the figure restoration error of 3D Automatic Fare Recognition Apparatus(3D-AFRA) in hardware Error Analysis. 2. Methods We scanned Face status by using 3D Automatic Face Recognition Apparatus(3D-AFRA). And also we scanned Face status by using laser scanner(vivid 9i). We compared facial shape data be restored by 3D Automatic Face Recognition Apparatus(3D-AFRA) with facial shape data that be restorated by 3D laser scanner. And we analysed the average error and the maximum error of two data. 3. Results and Conclusions In frontal face, the average error was 0.48mm. and the maximum error was 4.60mm. In whole face, the average error of was 0.99mm. And the maximum error was 6.64mm. In conclusion, We assessed that accuracy of 3D Automatic Face Recognition Apparatus(3D-AFRA) is considerably good.

• Journal of Sasang Constitutional Medicine
• /
• v.20 no.1
• /
• pp.34-41
• /
• 2008

1. Objectives We had been developing a 3D Automatic Face Recognition Apparatus (3D-AFRA) in order to evaluate the external appearances with more objectivity. This apparatus provides a 3D image and numerical data on facial configuration, and this study aims to evaluate the accuracy of 3D-AFRA recognition. 2. Methods Each scanned pictures were pointed with the 3D Automatic Face Recognition Apparatus(3D-AFRA). And the results were compared with data pointed pictures with manual. And we analysed the difference between Automatic and manual by paired -test. 3. Results and conclusions In frontal face, the P-value was more than 0.05. In conclusion, We assessed that accuracy of recognition of 3D Automatic Face Recognition Apparatus(3D-AFRA) is considerably good. But we should develop methods of measurement for lateral face and indistinct points of frontal face.